DeWalt DW328K User manual

Brand: DeWalt

Model: DW328K

Category: Circular saws

Type: User manual

This manual is also suitable for

DW328

INSTRUCTION MANUAL

GUIDE D’UTILISATION

MANUAL DE INSTRUCCIONES

DW328

Variable Speed Portable Band Saw

Scies à ruban portatives de vitesse variable

Sierras de banda portátiles de la velocidad variable

INSTRUCTIVO DE OPERACIÓN, CENTROS DE SERVICIO Y PÓLIZA

DE GARANTÍA. ADVERTENCIA: LÉASE ESTE INSTRUCTIVO ANTES

DE USAR EL PRODUCTO.

DEWALT Industrial Tool Co., 701 East Joppa Road, Baltimore, MD 21286

The following are trademarks for one or more DEWALT power tools: the yellow and black color scheme;

the “D” shaped air intake grill; the array of pyramids on the handgrip; the kit box configuration; and the

array of lozenge-shaped humps on the surface of the tool.

IF YOU HAVE ANY QUESTIONS OR COMMENTS ABOUT THIS OR ANY DEWALT TOOL,

CALL US TOLL FREE AT: 1-800-4-DEWALT (1-800-433-9258)

General Safety Instructions

WARNING! Read and understand all instructions. Failure to follow all

instructions listed below may result in electric shock, fire and/or serious

personal injury.

SAVE THESE INSTRUCTIONS

WORK AREA

• Keep your work area clean and well lit. Cluttered benches and dark areas invite

accidents.

• Do not operate power tools in explosive atmospheres, such as in the presence of

flammable liquids, gases, or dust. Power tools create sparks which may ignite the dust

or fumes.

• Keep bystanders, children, and visitors away while operating a power tool.

Distractions can cause you to lose control.

ELECTRICAL SAFETY

• Grounded tools must be plugged into an outlet properly installed and grounded in

accordance with all codes and ordinances. Never remove the grounding prong or

modify the plug in any way. Do not use any adaptor plugs. Check with a qualified

electrician if you are in doubt as to whether the outlet is properly grounded. If the

tools should electrically malfunction or break down, grounding provides a low resistance

path to carry electricity away from the user.

• Avoid body contact with grounded surfaces such as pipes, radiators, ranges and

refrigerators. There is an increased risk of electric shock if your body is grounded.

• Don’t expose power tools to rain or wet conditions. Water entering a power tool will

increase the risk of electric shock.

• Do not abuse the cord. Never use the cord to carry the tools or pull the plug from

an outlet. Keep cord away from heat, oil, sharp edges or moving parts. Replace

damaged cords immediately. Damaged cords increase the risk of electric shock.

• When operating a power tool outside, use an outdoor extension cord marked

“W-A” or “W.” These cords are rated for outdoor use and reduce the risk of electric

shock. When using an extension cord, be sure to use one heavy enough to carry the

current your product will draw. An undersized cord will cause a drop in line voltage

resulting in loss of power and overheating. The following table shows the correct size to

use depending on cord length and nameplate ampere rating. If in doubt, use the next

heavier gage. The smaller the gage number, the heavier the cord.

Minimum Gage for Cord Sets

Volts Total Length of Cord in Feet

120V 0-25 26-50 51-100 101-150

240V 0-50 51-100 101-200 201-300

Ampere Rating

More Not more AWG

Than Than

0-6 18 16 16 14

6 - 10 18 16 14 12

PERSONAL SAFETY

• Stay alert, watch what you are doing and use common sense when operating a

power tool. Do not use tool while tired or under the influence of drugs, alcohol, or

medication. A moment of inattention while operating power tools may result in serious

personal injury.

• Dress properly. Do not wear loose clothing or jewelry. Contain long hair. Keep

your hair, clothing, and gloves away from moving parts. Loose clothing, jewelry, or

long hair can be caught in moving parts. Air vents often cover moving parts and should

also be avoided.

• Avoid accidental starting. Be sure switch is off before plugging in. Carrying tools

with your finger on the switch or plugging in tools that have the switch on invites

accidents.

• Remove adjusting keys or wrenches before turning the tool on. A wrench or a key

that is left attached to a rotating part of the tool may result in personal injury.

• Do not overreach. Keep proper footing and balance at all times. Proper footing and

balance enables better control of the tool in unexpected situations.

• Use safety equipment. Always wear eye protection. Dust mask, non-skid safety shoes,

hard hat, or hearing protection must be used for appropriate conditions.

TOOL USE AND CARE

• Use clamps or other practical way to secure and support the workpiece to a stable

platform. Holding the work by hand or against your body is unstable and may lead to loss

of control.

• Do not force tool. Use the correct tool for your application. The correct tool will do the

job better and safer at the rate for which it is designed.

• Do not use tool if switch does not turn it on or off. Any tool that cannot be controlled

with the switch is dangerous and must be repaired.

• Disconnect the plug from the power source before making any adjustments,

changing accessories, or storing the tool. Such preventative safety measures reduce

the risk of starting the tool accidentally.

• Store idle tools out of reach of children and other untrained persons. Tools are

dangerous in the hands of untrained users.

• Maintain tools with care. Keep cutting tools sharp and clean. Properly maintained

tools, with sharp cutting edges are less likely to bind and are easier to control.

• Check for misalignment or binding of moving parts, breakage of parts, and any

other condition that may affect the tool’s operation. If damaged, have the tool

serviced before using. Many accidents are caused by poorly maintained tools.

• Use only accessories that are recommended by the manufacturer for your model.

Accessories that may be suitable for one tool, may become hazardous when used on

another tool.

SERVICE

• Tool service must be performed only by qualified repair personnel. Service or main-

tenance performed by unqualified personnel could result in a risk of injury.

• When servicing a tool, use only identical replacement parts. Follow instructions in

the Maintenance section of this manual. Use of unauthorized parts or failure to follow

maintenance instructions may create a risk of electric shock or injury.

Additional Safety Rules for Portable Band Saws

• Hold tool by insulated gripping surfaces when performing an operation where the

cutting tool may contact hidden wiring. Contact with a “live” wire will make exposed

metal parts of the tool “live” and shock the operator.

• Keep hands away from cutting area and blade. Keep one hand on the main handle

and the other hand on the front handle to prevent loss of control which could result in

personal injury.

• Always make sure the portable band saw is clean before using.

• Always cease operation at once if you notice any abnormality whatsoever.

• Always be sure all components are mounted properly and securely before using tool.

• Always handle the band saw blade with care when mounting or removing it.

• Always keep your hands out of the line of the band saw blade.

• Always wait until the motor has reached full speed before starting a cut.

• Always keep handles dry, clean, and free of oil and grease. Hold the tool firmly when in

use.

• Always be alert at all times, especially during repetitive, monotonous operations. Always

be sure of position of your hands relative to the blade.

• Never remove material guide/work stop.

• Stay clear of end pieces that may fall after cutting off. They may be hot, sharp and/or

heavy. Serious personal injury may result.

WARNING: DO NOT modify and/or use this tool for any application other than for which

it was designed.

WARNING: Shock Hazard. Exercise extreme caution when cutting blind into conduit and

pipe. Be sure the object being cut does not contain electrical wires, gases, or water, etc.,

which could create hazardous conditions causing personal injury and property damage.

WARNING: Some dust created by power sanding, sawing, grinding, drilling, and other

construction activities contains chemicals known to cause cancer, birth defects or other

reproductive harm. Some examples of these chemicals are:

• lead from lead-based paints,

• crystalline silica from bricks and cement and other masonry products, and

• arsenic and chromium from chemically-treated lumber (CCA).

Your risk from these exposures varies, depending on how often you do this type of work. To

reduce your exposure to these chemicals: work in a well ventilated area, and work with

approved safety equipment, such as those dust masks that are specially designed to filter out

microscopic particles.

• Avoid prolonged contact with dust from power sanding, sawing, grinding, drilling,

and other construction activities. Wear protective clothing and wash exposed areas

with soap and water. Allowing dust to get into your mouth, eyes, or lay on the skin may

promote absorption of harmful chemicals.

WARNING: Use of this tool can generate and/or disburse dust, which may cause serious

and permanent respiratory or other injury. Always use NIOSH/OSHA approved respiratory

protection appropriate for the dust exposure. Direct particles away from face and body.

• The label on your tool may include the following symbols. The symbols and their defini-

tions are as follows:

V ............volts A................amperes

Hz ..........hertz W ..............watts

min..........minutes ............alternating current

........direct current

o ..............no load speed

............Class I Construction ..............earthing terminal

................(grounded) ..............safety alert symbol

............Class II Construction …/min........revolutions or reciprocation

................(double insulated) ..................per minute

sfpm ........surface feet per minute

SAVE THESE INSTRUCTIONS

COMPONENTS (FIG. 1, 2)

A. Auxiliary handle I. Speed wheel

B. Lock button J. Blade

C. Trigger switch K. Rubber tires

D. Main handle L. Pulley

E. Material guide/Work stop M. Blade guard

F. Guide rollers

G. Blade tracking adjustment

H. Blade tension lever

ASSEMBLY

Blades

This portable band saw is setup for use with .020" (0.5 mm) thick, 1/2" (12.5 mm) wide

and 44-7/8" (1140 mm) long blades. To use .025 (.64 mm) thick blades, please contact an

authorized D

EWALT service center.

WARNING: The use of any other blade or accessory might be hazardous. DO NOT use

any other type of accessory with your band saw. Blades used on stationary band saws are

of different thickness. Do not attempt to use them on your portable unit.

Blade Selection

In general, first consider the size and shape of the work, and the type of material to be cut.

Remember, for the most efficient cutting, the coarsest tooth blade possible should be used in

a given application, because the coarser the tooth, the faster the cut. In selecting the appro-

priate number of teeth per inch of the band saw blade, at least two teeth should contact the

work surface when the blade is rested against the workpiece. As a rule of thumb, soft materi-

als usually require coarse tooth blades, while hard materials require fine tooth blades. Where

a smoother finish is important, select one of the finer tooth blades.

Select the appropriate band saw blade according to the material type, dimensions, and num-

ber of teeth. See Blade Description chart.

CAUTION: The following table is intended as a general guide only. Determine the type of

material and dimension of the workpiece and select the most appropriate band saw blade.

Incorrect blade application may result in loss of control causing personl injury.

If you have questions or comments, contact us.

Pour toute question ou tout commentaire, nous contacter.

Si tiene dudas o comentarios, contáctenos.

1-800-4-DEWALT • www.dewalt.com

FIG. 3

CAUTION: Never use the band saw to cut resin materials which are subject to melting.

Melting of resin material caused by high heat generated during cutting may cause the band

saw blade to become bound to the material, possibly resulting in overload and burn-out of the

motor.

Blade Speed

Your DW328 portable band saw is equipped with variable speed for greater versatility. Turn

the speed wheel (I) to select the desired speed (Fig. 1). Speed 1 is the slowest speed; Speed

6 is the fastest. Use speed settings 1–6 when connected to an AC power supply. When

connected to a DC power supply the setting MUST be Speed 6.

CAUTION: To avoid damage to the variable speed switch, always use Speed 6 (fastest)

when using a DC power source. Always turn the saw off, set the speed wheel (I) to Speed 6,

then turn the saw on.

When cutting copper, brass, bronze, aluminum, cast iron, angle iron, and mild steel, use a

higher speed.

When cutting plastic pipe, tougher steels, chrome steel, tungsten steel, stainless steel, and

other problem materials, use low speed.

NOTE: When cutting plastic pipe, higher speeds may melt plastic.

Removing and Installing Blades

WARNING: Turn off and unplug the tool before making any adjustments or

removing/installing attachments or accessories.

CAUTION: Cut Hazard. Blade tension lever is under spring pressure. Maintain control of

lever when releasing blade tension or blade may be released causing personal injury.

TO REMOVE BLADE (FIG. 1, 2)

1. Rotate the blade tension lever (H) clockwise until it stops to release tension in blade.

2. Turn the saw over and place it on a workbench or table with the cord to the left.

3. Begin removing the blade at the blade guard (M) and continue around the pulleys (L).

When removing the blade, tension may be released and the blade may spring free. SAW

BLADES ARE SHARP. USE CARE IN HANDLING THEM.

4. Inspect the guide rollers (F1, F2) and remove any large chips which may be lodged in

them. Lodged chips can prevent rotation of the guide rollers and cause flat spots on the

guide rollers.

5. Rubber tires (K) are mounted on the pulleys (L). The rubber tires should be inspected for

looseness or damage when changing the blade. Wipe any chips from the rubber tires on

the pulleys. This will extend tire life and keep the blade from slipping. If any looseness or

damage occurs, the tool should be brought to an authorized D

EWALT service center for

repair or replacement as soon as possible. Continued use of the tool with loose or

damaged rubber tires will cause unstable travel of the band saw blade.

TO INSTALL BLADE

1. Position the blade so that the teeth are on the bottom and angled toward the material

guide/work stop, as shown in Figures 1 and 3.

2. Slip the blade into the guide rollers (F), as shown in Figure 4.

3. Holding the blade in the guide rollers, place it around both pulleys (L) and through the

material guide/work stop (E), as shown in Figure 5.

4. Make sure that the blade is fully inserted into the guide rollers (F) and positioned square-

ly against the rubber tires (K).

5. Gently turn the saw over so that the pulleys rest on your work bench or table and rotate

the blade tension lever (H) counterclockwise until it stops. Make sure the teeth face away

from the bandsaw (Fig. 1, 3).

6. Turn the saw on and off a few times to ensure that the blade is seated properly.

Blade Tracking

WARNING: Turn off and unplug the tool before making any adjustments or

removing/installing attachments or accessories.

Your band saw is equipped with an adjustable blade tracking mechanism which assures

proper blade tracking at all times. The back edge of a properly aligned blade will run

lightly against one or both of the back up rollers in the blade guides. (The pressure between

the edge of the blade and the roller will be very slight and will not damage either the blade

or the roller.)

TO ADJUST THE BLADE TRACKING

1. Use a 9/16" (20mm) wrench to loosen the adjustment locking nut (G), shown in Figure 1

by turning it one or two turns counterclockwise.

2. Use a screwdriver to turn the tracking screw 1/4 turn. Turning the screw clockwise will

move the blade up toward the blade guide rollers. Turning the screw counterclockwise

will move the blade down away from the rollers.

3. Adjust so that the back edge of the blade lightly touches the rollers then securely tighten

the locking nut. (It will be necessary to plug the saw in and run it to observe the tracking.)

4. Observe blade tracking between runs and repeat Steps 1–4 as necessary to achieve

proper blade tracking.

BLADE DESCRIPTION

Type of band saw blade Bi-Metal

Number of teeth per inch 24 18 14 10 14/18 10/14

Workpiece thickness

1/8" and under • •

1/8"- 1/4" • •

1/4" - 13/32" • •

13/32" and over •

BLADE

DIRECTION

DIRECTION DE

LA LAME

DIRECCIÓN

DE LA HOJA

FIG 4

Item Model DW328

Motor Type Protected type, series commutator motor

Power source single-phase, AC 60Hz

Voltage 120 volts

Full-load current 6 amp

Band Saw Dimensions 1/2" x 44-7/8" x .020"

(12.5 mm x 1140 mm x .5 mm)

Blade Peripheral speed 100 - 265 ft/min (30 -80 m/min)

Max. Cutting Pipe outer dimensions 4-3/4" (120 mm)

Dimensions Stock 4-1/2" x 4-3/4" (114 mm x 120 mm)

Net Weight 14 lbs. (6.4 kg)

Cord 3 conductor type captive cable 8.0 ft. (2.4 m)

FIG. 1

FIG. 2

FIG. 5

BLADE DIRECTION / DIRECTION DE LA LAME / DIRECCIÓN DE LA HOJA

YES / OUI / SÍ

NO / NON / NO

FIG. 7

RECOMMENDED CUTTING POSITIONS / POSITIONS DE COUPE

RECOMMANDÉES / POSICIONES DE CORTE RECOMENDADAS

FIG. 6

POSITION OF TEETH ON LEFT SIDE OF MACHINE

POSITION DES DENTS DU CÔTÉ GAUCHE, SUR LE CÔTÉ DE LA MACHINE

POSICIÓN DE LOS DIENTES SOBRE LADO IZQUIERDO DEL COSTADO DE LA MÁQUINA

Article Modèle DW328

Moteur Type Type protégé, série moteur à collecteur

Circuit d’alimentation électrique monophasé, c.a., 60Hz

Tension 120 volts

Courant de pleine charge 6 A

Lame de scie Dimensions 12,5 mm x 1 140 mm x 0,5 mm

à ruban (1/2 po x 44-7/8 po x .020 po)

Vitesse périphérique 30 à 80 m/min (100 - 265 pi/min)

Dimensions Dimensions externes du tuyau 120 mm (4-3/4 po)

maximales Matériau à couper 114 mm x 120 mm

de la coupe (4-1/2 po x 4-3/4 po)

Poids net 6,4 kg (14 lb)

Cordon Fiche à 3 broches et à 3

conducteurs de 2,4 m (8,0 pi))

Artículo Modelo DW328

Motor Tipo Motor conmutador en serie, tipo protegido

Fuente de alimentación CA 60 Hz, monofásica

Voltaje 120 voltios

Corriente a plena carga 6 amperios

Hoja de la sierra Dimensiones 12,5 mm x 1 140 mm x 0,5 mm

de banda (1/2 pulg. x 44-7/8 pulg. x .020 pulg.)

Velocidad periférica 30 - 80 m/min (100 - 265 pies/min)

Dimensiones Dimensiones exteriores

máximas de de tubería 120 mm (4-3/4 pulg.)

corte Material a cortar 114 mm x 120 mm (4-1/2 x 4-3/4 pulg.)

Peso neto 6,4 kg (14 lb)

Cable Cable cautivo de 3 conductores, de 2,4 m

(8,0 pies) de largo

YES / OUI / SÍ

YES / OUI / SÍYES / OUI / SÍ

YES / OUI / SÍ

NO / NON / NO

OPERATION

Motor

Be sure your power supply agrees with the voltage marked on the nameplate. 120 Volts AC

60Hz means alternating current only. Voltage decrease of more than 10% will cause loss of

power and overheating. All D

EWALT tools are factory-tested. If this tool does not operate,

check the power supply line for blown fuses and the plug and receptacle for proper contact.

This band saw is designed to cut various types of material up to 4-3/4" (120 mm) diameter

or 4-1/2" (114 mm) x 4-3/4" (120 mm) rectangular shape at 90˚.

WARNING: Thoroughly remove any oil or grease from the workpiece before securing in a

vise or other clamping device. If the workpiece is not secure, it may come loose during the

cutting and/or cause breakage, which may result in serious personal injury.

WARNING: Never connect the tool to a power source unless the voltage of the source is

the same as the voltage specified on the nameplate of the tool. An overspeed blade and

overheating and may occur causing personal injury.

WARNING: Laceration Hazard. If the power cord is connected to the power source with

the trigger switch turned ON the power tool will start suddenly and could cause a serious

accident.

Trigger Switch (Fig. 1)

To start the tool, squeeze the trigger switch (C). To turn the tool off, release the switch.

A lock button (B) is provided to keep the saw running without holding the trigger switch “ON.”

To lock the switch trigger “ON,” squeeze the trigger as far as it will go, push in the lock

button and release the trigger. To disengage the lock button, squeeze and release the trigger

switch.

Cutting

WARNING: Refer to Figure 7 for recommended cutting positions for various materials.

Loss of control causing serious injury may occur.

NOTE: Select and use a band saw blade that is most appropriate for the material being cut.

For more information, refer to Blade Selection.

1. Mount the material to be cut solidly in a vise or other clamping device. Never attempt to

use this tool by resting it on a work surface and bringing the material to the tool. Always

securely clamp the workpiece and bring the tool to the workpiece, securely holding the

tool with two hands as shown in Figure 6.

2. Bring the material guide/work stop (E) into contact with the workpiece. Turn the saw ON.

3. When saw reaches desired rotation speed, slowly and gently tilt the main body of the tool

to bring the band saw blade into contact with the workpiece. Do not apply additional pres-

sure in excess of the weight of the main body of the tool. Carefully avoid bringing the band

saw blade suddenly and heavily into contact with the upper surface of the workpiece. This

will cause serious damage to the band saw blade. To obtain maximum service life of the

band saw blade, ensure there is no sudden impact at the beginning of the cutting opera-

tion.

CAUTION: During cutting, if the band saw becomes locked or jammed in the workpiece

material, release the switch immediately to avoid damage to the band saw blade and motor.

4. The tool’s own weight provides the most efficient downward cutting pressure. Added

operator pressure slows the blade and reduces blade life.

5. End pieces, which would be heavy enough to cause injury when they drop, after cut-off,

should be supported. Safety shoes are strongly recommended. End pieces may be hot.

6. Hold the saw firmly in both hands so that the saw does not fall against clamped or

supported material when the cut is completed. DO NOT MAKE ANY SPEED CHANGES

UNLESS TOOL HAS BEEN TURNED OFF.

Tips for Better Cutting

The following recommendations should be used as a guide. Results may vary with the oper-

ator and the particular material being cut.

• Never twist the band saw blade during cutting operation.

• Never use liquid coolants with portable band saws. Use of liquid coolants will cause build-

up on tires and reduce performance.

• If excessive vibration occurs during the cut, turn the bandsaw off and adjust the speed

slightly. Ensure that the material being cut is is securely clamped down. If vibration

continues, change the band saw blade.

MAINTENANCE

WARNING: To avoid accidental injury, turn off and unplug the tool before making

any adjustments, performing any maintenance or inspection of this tool.

Cleaning

CAUTION: Never use solvents or other harsh chemicals for cleaning the non-metallic

parts of the tool. These chemicals may weaken the plastic materials used in these parts. Use

a cloth dampened only with water and mild soap. Never let any liquid get inside the tool; never

immerse any part of the tool into a liquid.

Periodically remove chips and other waste material from the surface of the power tool by

using a damp cloth and mild soap. Many household cleaners contain chemicals which could

seriously damage plastic. Also, do not use gasoline, turpentine, lacquer or paint thinner, dry

cleaning fluids or similar products. To avoid malfunction of the motor, protect it from contact

with oil or water.

Repairs

To assure product SAFETY and RELIABILITY, repairs, maintenance and adjustments should

be performed by a D

EWALT factory service center, a DEWALT authorized service center or

other qualified service personnel. Always use identical replacement parts.

ACCESSORIES

Recommended accessories for use with your tool are available at extra cost from your local

dealer or authorized service center. If you need assistance in locating any accessory, please

contact D

EWALT Industrial Tool Co., 701 East Joppa Road, Baltimore, MD 21286, call 1-800-

4-D

EWALT (1-800-433-9258) or visit our website www.dewalt.com.

WARNING: The use of any other accessory not recommended for use with this tool could

be hazardous.

Three Year Limited Warranty

DEWALT will repair, without charge, any defects due to faulty materials or workmanship for

three years from the date of purchase. This warranty does not cover part failure due to nor-

mal wear or tool abuse. For further detail of warranty coverage and warranty repair informa-

tion, visit www.dewalt.com or call 1-800-4-D

EWALT (1-800-433-9258). This warranty does

not apply to accessories or damage caused where repairs have been made or attempted by

others. This warranty gives you specific legal rights and you may have other rights which vary

in certain states or provinces.

In addition to the warranty, D

EWALT tools are covered by our:

1 YEAR FREE SERVICE

EWALT will maintain the tool and replace worn parts caused by normal use, for free, any

time during the first year after purchase.

90 DAY MONEY BACK GUARANTEE

If you are not completely satisfied with the performance of your D

EWALT Power Tool, Laser,

or Nailer for any reason, you can return it within 90 days from the date of purchase with a

receipt for a full refund – no questions asked.

LATIN AMERICA: This warranty does not apply to products sold in Latin America. For prod-

ucts sold in Latin America, see country specific warranty information contained either in the

packaging, call the local company or see website for warranty information.

FREE WARNING LABEL REPLACEMENT: If your warning labels become illegible or are

missing, call 1-800-4-D

EWALT for a free replacement.

SI VOUS AVEZ DES QUESTIONS OU VOUS VOULEZ NOUS FAIRE PART DE VOS

COMMENTAIRES CONCERNANT CET OUTIL OU TOUT AUTRE OUTIL D

EWALT,

COMPOSEZ SANS FRAIS LE : 1 800 433-9258. (1-800-4-D

EWALT).

Consignes de sécurité - généralités

AVERTISSEMENT : Lire, comprendre et suivre toutes les directives

précisées ci-dessous afin d’éviter les risques de choc électrique, d’incendie

ou de blessure grave.

CONSERVER CES DIRECTIVES

AIRE DE TRAVAIL

• Garder l’aire de travail propre et bien éclairée; les établis encombrés et les endroits

sombres sont propices aux accidents.

• Ne pas utiliser les outils électriques dans une atmosphère explosive, comme à

proximité de liquides, de gaz ou de poussières inflammables; le moteur peut créer

des étincelles et enflammer les vapeurs ou les poussières environnantes.

• Tenir les enfants, les visiteurs ou toute autre personne à l’écart lorsqu’on utilise un

outil électrique; les distractions peuvent faire perdre la maîtrise de ce dernier.

MESURES DE SÉCURITÉ – ÉLECTRICITÉ

• Les outils mis à la terre doivent être branchés dans une prise correctement instal-

lée et mise à la terre tel que l’indiquent les codes et règlements en vigueur. Ne

jamais retirer la broche de mise à la terre ou modifier la prise en aucune façon. Ne

pas utiliser de fiche d’adaptation. Consulter un électricien qualifié s’il y a un doute

en ce qui concerne la mise à la terre de la prise. En cas de défaillance électrique ou

de bris de l’outil, la mise à la terre procure un chemin de faible résistance au courant afin

de réduire les risques de choc électrique.

• Éviter tout contact entre le corps et les éléments mis à la terre, comme les tuyaux,

les radiateurs, les cuisinières et les réfrigérateurs, afin de réduire les risques de choc

électrique.

• Ne pas utiliser l’outil électrique dans des endroits mouillés, ni l’exposer à la pluie;

l’infiltration d’eau à l’intérieur de l’outil augmente les risques de choc électrique.

• Ne pas utiliser le cordon de manière abusive; on ne doit pas transporter l’outil en

le tenant par le cordon, ou utiliser ce dernier pour le débrancher. On doit tenir le

cordon à l’écart des sources de chaleur, de l’huile, des bords tranchants ou des

pièces mobiles. Remplacer immédiatement les cordons endommagés, car ces

derniers augmentent les risques de choc électrique.

• Lorsqu’on utilise un outil électrique à l’extérieur, on ne doit utiliser que des

rallonges conçues pour cet usage, comme celles de type W-A ou W, afin de réduire

les risques de choc électrique. S’assurer que la rallonge est en mesure de porter le

courant nécessaire à l’outil. Une rallonge de calibre inférieur entraînera une chute de

tension se traduisant par une perte de puissance et une surchauffe. Le tableau ci-dessous

illustre les calibres que l’on doit utiliser selon la longueur de la rallonge et l’intensité

nominale indiquée sur la plaque signalétique. En cas de doute, utiliser le calibre suivant.

Plus le calibre est petit, plus la rallonge peut porter de courant.

Calibre minimal des cordons de rallonge

Tension Longueur totale de la rallonge en mètres

120 V De 0 à 7,6 De 7,6 à 15,2 De 15,2 à 30,4 De 30,4 à 45,7

240 V De 0 à 15,2 De 15,2 à 30,4 De 30,4 à 60,9 De 60,9 à 91,4

Intensité nominale (en amperes)

Plus dePas plus de Calibre AWG

0-6 18 16 16 14

6 - 10 18 16 14 12

SÉCURITÉ PERSONNELLE

• Rester vigilant en tout temps et faire preuve de jugement lorsqu’on utilise un outil

électrique. Ne pas utiliser l’outil lorsqu’on est fatigué ou sous l’influence de

drogues, d’alcool ou de médicaments, car un moment d’inattention pourrait entraîner

des blessures graves.

• Porter des vêtements appropriés. Ne pas porter des vêtements amples ou des

bijoux. Couvrir ou attacher les cheveux longs. Garder les cheveux, les vêtements,

les bijoux et les gants éloignés des pièces mobiles, car ceux-ci peuvent s’y coincer.

Se tenir éloigné des évents puisque ces derniers pourraient camoufler des pièces

mobiles.

• Éviter les démarrages accidentels; s’assurer que l’interrupteur est en position

d’arrêt avant de brancher l’outil. Ne pas transporter l’outil en laissant le doigt sur

l’interrupteur ni le brancher lorsque l’interrupteur est en position de marche, car cela

pourrait causer un accident.

• Retirer les clés de réglage avant de démarrer l’outil. Une clé laissée sur une pièce

rotative pourrait entraîner des blessures.

• Ne pas trop étendre les bras. Les pieds doivent rester ancrés fermement au sol afin

de maintenir son équilibre en tout temps et de mieux maîtriser l’outil dans des situa-

tions imprévues.

• Utiliser le matériel de sécurité approprié; toujours porter des lunettes de protection.

Porter un masque anti-poussières, des chaussures antidérapantes, un casque de

sécurité ou des protecteurs auditifs lorsque la situation le requiert.

UTILISATION ET ENTRETIEN DE L’OUTIL

• Fixer et soutenir la pièce sur une plate-forme stable au moyen d’une bride de

serrage ou de tout autre dispositif semblable. La pièce est instable lorsqu’on la retient

manuellement ou qu’on l’appuie contre le corps, ce qui pourrait faire perdre la maîtrise de

l’outil.

• Ne pas forcer l’outil ni l’utiliser pour des travaux autres que ceux pour lesquels il a

été conçu. Pour obtenir de meilleurs résultats et prévenir les risques de blessure, laisser

l’outil couper à la vitesse pour laquelle il a été conçu.

• Ne pas utiliser l’outil lorsque l’interrupteur marche-arrêt ne fonctionne pas. Tout

outil qui ne peut être commandé au moyen de l’interrupteur est dangereux et doit être

réparé

• Débrancher l’outil de la source d’alimentation électrique avant d’effectuer un

réglage, de changer les accessoires ou de ranger l’outil; ces mesures de sécurité

préventives réduisent les risques de démarrage accidentel.

• Lorsqu’on n’utilise pas l’outil, le ranger hors de la portée des enfants ou des

personnes non qualifiées. Les outils sont dangereux entre les mains de personnes

inexpérimentées.

• Bien entretenir l’outil; s’assurer qu’il est toujours bien propre et aiguisé. Les outils

bien entretenus et dont les bords sont bien tranchants sont moins susceptibles de rester

coincés et sont plus faciles à maîtriser.

• Vérifier les pièces mobiles afin de s’assurer qu’elles sont bien alignées et qu’elles

ne restent pas coincées. Vérifier également les pièces afin de s’assurer qu’il n’y a

aucun bris ni aucune autre condition susceptible de nuire au bon fonctionnement

de l’outil. Faire réparer l’outil si ce dernier est endommagé avant de s’en servir à

nouveau, car les accidents sont souvent causés par des outils mal entretenus.

• N’utiliser que les accessoires recommandés par le fabricant pour le modèle

concerné. Un accessoire destiné à un outil particulier peut devenir dangereux lorsqu’il est

utilisé avec un autre.

ENTRETIEN

• L’outil doit être entretenu par le personnel qualifié seulement; toute maintenance

effectuée par une personne non qualifiée pourrait entraîner des risques de blessure.

• Lors de l’entretien, n’utiliser que des pièces de rechange identiques et suivre les

directives précisées à la section « Entretien » du présent guide afin de prévenir les

risques de choc électrique ou de blessure.

Régles de sécurité additionnelles concernant les

scies à ruban portatives

• Tenir l’outil par les surfaces isolées prévues à cette fin lorsqu’il risque d’entrer en

contact avec des fils cachés, car de tels contacts peuvent mettre les pièces métalliques

de l’outil sous tension, engendrant des risques de choc électrique.

• Tenir les mains éloignées de l’aire de coupe et de la lame. Garder une main sur la

poignée principale et l’autre, sur la poignée avant afin d’éviter de perdre la maîtrise de

l’outil et de risquer des blessures.

• Toujours s’assurer que la scie à ruban portative est propre avant de l’utiliser.

• Toujours arrêter immédiatement le fonctionnement de la scie lorsqu’on remarque une

anomalie.

Page is loading ...

DeWalt DW328K User manual

Brand: DeWalt

Model: DW328K

Category: Circular saws

Type: User manual

This manual is also suitable for

DW328

Download PDF

report

in other languages

français: DeWalt DW328K Manuel utilisateur
español: DeWalt DW328K Manual de usuario

DeWalt DW328K User manual

This manual is also suitable for

DeWalt DW328K User manual

in other languages

Related papers

Other documents