Skil 0730 AS User manual

Category
Grass trimmers
Type
User manual
LINE TRIMMER
0730 (F0150730..)
SKIL Europe BV - Konijnenberg 60 07/12 2610Z02454
4825 BD Breda - The Netherlands
www.skil.com

ORIGINAL INSTRUCTIONS
6
NOTICE ORIGINALE
9
ORIGINALBETRIEBSANLEITUNG
12

ORIGINELE GEBRUIKSAANWIJZING
15
BRUKSANVISNING I ORIGINAL
18

ORIGINAL BRUGSANVISNING
21
ORIGINAL BRUKSANVISNING
25

ALKUPERÄISET OHJEET
27
MANUAL ORIGINAL
30
MANUAL ORIGINAL
34
ISTRUZIONI ORIGINALI
37
EREDETI HASZNÁLATI UTASÍTÁS
40

PŮVODNÍM NÁVODEM K POUŽÍVÁNÍ
44

ORİJİNAL İŞLETME TALİMATI
47

INSTRUKCJA ORYGINALNA
50

ПОДЛИННИК РУКОВОДСТВА
ПО ЭКСПЛУАТАЦИИ
53

ОРИГІНАЛЬНА ІНСТРУКЦІЯ
З ЕКСПЛУАТАЦІЇ
57

ΠΡΩΤΟΤΥΠΟ Ο∆ΗΓΙΩΝ ΧΡΗΣΗΣ
61

INSTRUCŢIUNI DE FOLOSIRE
ORIGINALE
64

ОРИГИНАЛНО РЪКОВОДСТВО
ЗА ЕКСПЛОАТАЦИЯ
68

PÔVODNÝ NÁVOD NA POUŽITIE
71

ORIGINALNE UPUTE ZA RAD
74

ORIGINALNO UPUTSTVO ZA RAD
77

IZVIRNA NAVODILA
80

ALGUPÄRANE KASUTUSJUHEND
83

ORIĢINĀLĀ LIETOŠANAS PAMĀCĪBA
86

ORIGINALI INSTRUKCIJA
90

99

97
ME77
6

Line trimmer 0730
INTRODUCTION
This tool is intended for the cutting of grass and weeds
under bushes as well as on slopes and edges that can
not be reached with a lawn mower
This tool is not intended for professional use
Check whether the packaging contains all parts as
illustrated in drawing 2
When parts are missing or damaged, please contact your
dealer
• Readthisinstructionmanualcarefullybeforeuse
andsaveitforfuturereference3
• Payspecialattentiontothesafetyinstructionsand
warnings;failuretofollowthesemayresultin
seriousinjury
TECHNICALSPECIFICATIONS1
TOOL ELEMENTS 2
A Cutting guard
B Guide handle
C Cord restraint
D Locking sleeve
E Telescopic tube
F Trigger switch
G Cutting blade cover
H Button for line feeding
J Line cutting blade
K Spool cap
L Ventilation slots
M Storage rail (screwsnotsupplied)
N Storage hook
SAFETY
SPECIFICSAFETYINSTRUCTIONSFORLINE
TRIMMERS
GENERAL
Be familiar with the controls and the proper use of the tool
The user is responsible for accidents or hazards
occurring to other people or their property
Only use the tool when the ambient temperature is
between 0°C and 40°C
Never mount metal cutting elements onto this tool
PERSONALSAFETY
• Thistoolisnotintendedforusebypersons
(includingchildren)withreducedphysical,sensory
ormentalcapabilities,orlackofexperienceand
knowledge,unlesstheyhavebeengiven
supervisionorinstructionconcerninguseofthe
toolbyapersonresponsiblefortheirsafety
• Ensurethatchildrendonotplaywiththetool
Never allow children or people who are not familiar with
the operating instructions to use the tool
• Keepyourfingersawayfromthelinecuttingblade
integratedinthecuttingguard
Keep hands and feet away from the cutting lines while
trimming, especially when switching on the tool
Always wear eye protection, long trousers and sturdy
shoes when operating the tool
Never operate the tool in the direct vicinity of persons;
stop using the tool while persons (especially children) or
pets are nearby
Never operate the tool when you are tired, sick or under
the inuence of alcohol or other drugs
ELECTRICALSAFETY
Always check that the supply voltage is the same as the
voltage indicated on the nameplate of the charger
(chargers with a rating of 230V or 240V can also be
connected to a 220V supply)
Inspect the cord periodically and have it replaced by a
qualied person, if damaged
Inspect the extension cord periodically and replace it, if
damaged (inadequateextensioncordscanbe
dangerous)
Only use an extension cord which is intended for outdoor
use and equipped with a watertight plug and coupling-
socket
Use completely unrolled and safe extension cords with a
capacity of 16 Amps (U.K. 13 Amps)
When operating the tool use a residual current device
(RCD) with a triggering current of 30 mA maximum
Do not run over, crush or pull the (extension) cord
Protect the (extension) cord from heat, oil and sharp
edges
• Keepthe(extension)cordawayfromtherotating
cuttinglines
Always switch o tool and disconnect plug from power
source if the power supply cord or the extension cord is
cut, damaged or entangled (donottouchthecord
beforedisconnectingtheplug)
BEFOREUSE
Only use the tool in daylight or with appropriate articial
lighting
Check the functioning of the tool before each use and after
any impact; in case of a defect, have it repaired immediately
by a qualied person (never open the tool yourself)
Before use, thoroughly inspect the cutting area and
remove any object that the tool may sling during cutting
(such as stones, loose pieces of wood, etc.)
DURING USE
Never use the tool when cord is damaged; have it
replaced by a qualied person
Never operate the tool with a damaged cutting guard or
without the cutting guard mounted
• Thecuttinglinescontinuetorotateforashorttime
afterthetoolisswitchedoff
Do not cut grass which is not on the ground (e.g. on walls
or rocks)
Do not cross roads or gravel paths with the tool still
running
Do not get distracted and always concentrate on what
you are doing
Always disconnect plug from power source
- whenever leaving the tool unattended
- before clearing jammed material
- before checking, cleaning or working on the tool
- after striking a foreign object
7
- whenever the tool starts vibrating abnormally
Always ensure that the ventilation openings are kept clear
of debris
AFTERUSE
• Alwaysswitchofftoolanddisconnectplugfrom
powersourcebeforemakingadjustments,changing
spools,cleaningorleavingthetoolunattendedfor
anyperiod
Store the tool indoors in a dry and locked-up place, out
of reach of children
EXPLANATIONOFSYMBOLSONTOOL
3Warning! Read the instruction manual
4 Do not expose tool to rain
5 Wear protective glasses
6 Payattentiontotheriskofinjurycausedbyflyingdebris
(keep bystanders a safe distance away from work area)
7 Immediately disconnect the plug if the (extension) cord is
damaged or cut through while working
8 Double insulation (no earth wire required)
WHEN CONNECTING NEW 3-PIN PLUG (U.K. ONLY):
If for any reason the old plug is cut o the cord of this tool,
it must be disposed of safely and not left unattended
Do not connect the blue (= neutral) or brown (= live) wire
in the cord of this tool to the earth terminal of the plug
USE
Cutting guard 0
- mount cutting guard A as illustrated with round head
screw supplied
! neverusethetoolwithoutcuttingguardA
Mounting/adjusting guide handle !
- mount guide handle B as illustrated with 4 screws
supplied
! firmlytightenall4screws
Cord restraint @
- hook the loop in the extension cord over restraint C as
illustrated
- pull tight to secure the extension cord
Height adjustment #
For adjusting the tool height so that your front arm is
straight when trimming
- loosen locking sleeve D 2 by turning it clockwise
- extend tube E 2 to the desired height
- tighten locking sleeve D 2 by turning it counter-clockwise
On/o $
- switch on tool by pressing trigger switch F
- switch o tool by releasing trigger switch F
! afterswitchingoffthetoolthecuttinglines
continuetorotateforafewseconds
- allow the cutting lines to stop rotating before switching
on again
! donotrapidlyswitchonandoff
Trimming
! ensurethattheredcoverG2isremovedfrom
thelinecuttingbladebeforeusingthetool
! ensurethatthecuttingareaisfreeofstones,
debrisandotherforeignobjects
! starttrimmingonlywhentoolrunsatfullspeed
- start trimming near the mains socket and move away
while working
- cut long grass in layers (always start from the top)
- only trim with the tip of the cutting line
- do not cut damp or wet grass
- prevent the cut grass from clogging the spool (do not
make heavy cuts)
- do not overload the tool
- carefully cut around trees and bushes, so that they do
not come into contact with the cutting lines
- keep the tool away from solid objects in order to
protect the cutting lines against excessive wear
- be aware of the kickback forces that occur when solid
objects are touched
Holding and guiding the tool %
- for cutting long grass slowly swing the tool from right to
left and vice versa
- for cutting shorter grass tilt the tool as illustrated
- turn the tool 180° for trimming edges
- hold tool rmly with both hands, so you will have full
control of the tool at all times
- maintain a stable working position
- always hold the tool well away from your body
Line feeding ^
- tap button H lightly on the ground (preferably on a
solid surface) while the motor is running
- two cutting lines will be released and cut o to the
correct length by line cutting blade J
! ensurethattheredcoverG2isremovedfrom
thelinecuttingbladebeforeusingthetool
! takecareagainstinjuryfromlinecuttingbladeJ
- after line feeding always return the tool to its normal
operating position before switching on
- feed the lines regularly to maintain full cutting circle
- when the motor runs without load and no grass is cut,
the cutting lines are worn or broken; rewind the spool
or replace the spool system
Rewinding spool &
In case the cutting lines fail to protrude from spool cap K
! switchoffthetoolanddisconnecttheplug
- remove spool system from tool and take out spool from
spool cap K
- tightly rewind both cutting lines evenly in layers in
arrow direction
- insert both lines into spool slots X and ensure that they
are securely in place (leave sucient length of line)
- thread both lines through spool holes Y before placing
the rewound spool into spool cap K
! ensurethatthespoolislocatedsecurelyinplace,
thenreleasebothlinesfromslotsXbypulling
themfirmly
- mount spool system onto tool (turnspoolclockwise
untilitclicksintoplace) *
Replacing spool system *
! switchoffthetoolanddisconnecttheplug
- simply remove/mount old/new spool system as
illustrated
- only use SKIL spool system 2610Z01354 with this tool
(damageduetousingotherspoolsystemswillbe
excludedfromthewarranty)
- after replacing the spool system test-run the tool for at
least one minute without load to ensure that the tool is
operating properly
8
MAINTENANCE / SERVICE
This tool is not intended for professional use
• Alwaysdisconnectplugfrompowersourcebefore
cleaningand/ormaintenance
Always keep tool and cord clean (especially the
ventilation slots)
- clean the tool with a damp cloth (do not use cleaning
agents or solvents)
- clean line cutting blade J 2 and cutting guard A after
each use
- clean ventilation slots L 2 regularly with a brush or
compressed air
Regularly check the condition of the cutting head and the
tightness of nuts, bolts and screws
Regularly check for worn or damaged components and
have them repaired/replaced when necessary
Storage (
- store the tool indoors in a dry and locked-up place,
out of reach of children
- securely mount storage rail M on the wall with 4
screws (notsupplied) and horizontally leveled
If the tool should fail despite the care taken in
manufacturing and testing procedures, repair should be
carried out by an after-sales service centre for SKIL
power tools
- send the tool undismantled together with proof of
purchase to your dealer or the nearest SKIL service
station (addresses as well as the service diagram of
the tool are listed on www.skil.com)
TROUBLESHOOTING
The following listing shows problem symptoms, possible
causes and corrective actions (if these do not identify
and correct the problem, contact your dealer or service
station)
! switchoffthetoolanddisconnecttheplugbefore
investigatingtheproblem
Tool does not operate
- power supply socket faulty -> use another socket
- extension cord damaged -> replace extension cord
Tool operates intermittently
- internal wiring defective -> contact dealer/service
station
- on/o switch defective -> contact dealer/service
station
Tool vibrates abnormally
- grass too high -> cut in stages
Tool does not cut
- line too short/broken o -> feed the line manually
Line cannot be fed
- spool empty -> replace spool
- line entangled inside spool -> inspect spool; rewind if
necessary
Line is not cut o to correct length -> remove cover from
cutting blade
Line keeps breaking
- line entangled inside spool -> inspect spool; rewind if
necessary
- trimmer incorrectly used -> only trim with the tip of the
line; avoid stones, walles and other hard objects; feed
the line regularly
ENVIRONMENT
Donotdisposeofelectrictools,accessoriesand
packagingtogetherwithhouseholdwastematerial
(only for EU countries)
- in observance of European Directive 2002/96/EC on
waste of electric and electronic equipment and its
implementation in accordance with national law,
electric tools that have reached the end of their life
must be collected separately and returned to an
environmentally compatible recycling facility
- symbol 9 will remind you of this when the need for
disposing occurs
DECLARATIONOFCONFORMITY
We declare under our sole responsibility that this product
is in conformity with the following standards or
standardized documents: EN 60335, EN 61000,
EN 55014 in accordance with the provisions of the
directives 2006/95/EC, 2004/108/EC, 2006/42/EC,
2000/14/EC, 2011/65/EU
Technicalfileat: SKIL Europe BV (PT-SEU/PJE),
4825 BD Breda, NL
¹ÊÁÂÆιÆ¼½ÊÇǾ¼½Æ
ȽʹÌÁÇÆËŵÆ¿Áƽ½ÊÁÆ¿
ÍÊÇȽƓˁ˅ʿ˂ʽ¼¹Ɠ
Ĺ¾ÁÂÿʹ¹¾
ÈÈÊÇιÄ¹Æ¹¿½Ê
25.07.2012
11
NOISE/VIBRATION
Measured in accordance with EN 60335 the sound
pressure level of this tool is 70 dB(A) and the sound
power level 90 dB(A) (standard deviation: 3 dB), and the
vibration <2.5 m/s² (hand-arm method; uncertainty
K = 1.5 m/s²)
Measured in accordance with 2000/14/EC (EN/ISO 3744)
the guaranteed sound power level LWA is lower than
93 dB(A) (conformity assessment procedure according to
Annex VI)
Notied body: KEMA, Arnhem, NL
Notied body identication number: 0344
The vibration emission level has been measured in
accordance with a standardised test given in EN 60335; it
may be used to compare one tool with another and as a
preliminary assessment of exposure to vibration when
using the tool for the applications mentioned
- using the tool for dierent applications, or with dierent
or poorly maintainted accessories, may signicantly
increase the exposure level
- the times when the tool is switched o or when it is
running but not actually doing the job, may signicantly
reduce the exposure level
! protectyourselfagainsttheeffectsofvibration
bymaintainingthetoolanditsaccessories,
keepingyourhandswarm,andorganizingyour
workpatterns
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8
  • Page 9 9
  • Page 10 10
  • Page 11 11
  • Page 12 12
  • Page 13 13
  • Page 14 14
  • Page 15 15
  • Page 16 16
  • Page 17 17
  • Page 18 18
  • Page 19 19
  • Page 20 20
  • Page 21 21
  • Page 22 22
  • Page 23 23
  • Page 24 24
  • Page 25 25
  • Page 26 26
  • Page 27 27
  • Page 28 28
  • Page 29 29
  • Page 30 30
  • Page 31 31
  • Page 32 32
  • Page 33 33
  • Page 34 34
  • Page 35 35
  • Page 36 36
  • Page 37 37
  • Page 38 38
  • Page 39 39
  • Page 40 40
  • Page 41 41
  • Page 42 42
  • Page 43 43
  • Page 44 44
  • Page 45 45
  • Page 46 46
  • Page 47 47
  • Page 48 48
  • Page 49 49
  • Page 50 50
  • Page 51 51
  • Page 52 52
  • Page 53 53
  • Page 54 54
  • Page 55 55
  • Page 56 56
  • Page 57 57
  • Page 58 58
  • Page 59 59
  • Page 60 60
  • Page 61 61
  • Page 62 62
  • Page 63 63
  • Page 64 64
  • Page 65 65
  • Page 66 66
  • Page 67 67
  • Page 68 68
  • Page 69 69
  • Page 70 70
  • Page 71 71
  • Page 72 72
  • Page 73 73
  • Page 74 74
  • Page 75 75
  • Page 76 76
  • Page 77 77
  • Page 78 78
  • Page 79 79
  • Page 80 80
  • Page 81 81
  • Page 82 82
  • Page 83 83
  • Page 84 84
  • Page 85 85
  • Page 86 86
  • Page 87 87
  • Page 88 88
  • Page 89 89
  • Page 90 90
  • Page 91 91
  • Page 92 92
  • Page 93 93
  • Page 94 94
  • Page 95 95
  • Page 96 96
  • Page 97 97
  • Page 98 98
  • Page 99 99
  • Page 100 100
  • Page 101 101
  • Page 102 102
  • Page 103 103
  • Page 104 104

Skil 0730 AS User manual

Category
Grass trimmers
Type
User manual

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI