Page is loading ...
IMPORTANT SAFEGUARDS
When using electrical equipment, basic safety precautions should always be followed including the following:
1. READ AND FOLLOW ALL SAFETY INSTRUCTIONS
2. Disconnect power before performing work on electrical equipment.
3. Do not let power cords touch hot surfaces and do not mount near gas or electric heaters.
4. Use caution when servicing batteries. Battery acid can cause burns to skin and eyes. If acid is spilled on skin or
eyes, flush with fresh water and contact a physician immediately.
5. Equipment should be mounted in locations and at heights where unauthorized personnel will not readily subject it to
tampering.
6. The use of accessory equipment not recommended by Beghelli may cause an unsafe condition, and will void the unit’s
warranty.
7. Do not use this equipment for other than its intended purpose.
8. Servicing of this equipment should be performed by qualified service personnel.
9. SAVE THESE INSTRUCTIONS!
INSTRUCTIONS
INSTALLATION
SURFACE MOUNTING
1. Extend unswitched 24 hour AC supply of rated voltage installed in accordance with all applicable codes and
standards. Leave at least 8 inches of slack wire. This circuit should NOT be energized/live at this time.
2. Open the unit by unscrewing the two (2) lens screws and (2) cover screws. (Figure 1)
3. Remove cover plate assembly.
4. Knock out 7⁄8" power entry hole.
5. Mount the unit securely into place. Install two (2) screws. Fasten each mounting foot with an appropriately sized
screw or mounting bolt (not supplied). (Figure 2)
6. Install liquid tight bushing, not supplied.
7. Make proper wiring connections between the AC supply and the unit’s transformer per diagram provided (Figure 4).
Insulate unused wire seperately! Connect ground to supplied green ground wire in accordance with local codes.
Reassemble all wire connections and connectors. CAUTION! - Failure to insulate unused wire may result in a
shock hazard or unsafe condition as well as equipment failure. All wires must be dressed and routed to ensure
they will not come in contact with the circuit board.
8. Connect the wire lead(s) from the positive circuit board terminal (+) to the positive terminal connector on the battery.
(Figure 5).
9. Re-install the cover plate assembly.
10. Position lamps to provide best lighting distribution. Manually rotate or twist lamp to desired position. (Figure 3)
11. Close lens and secure with (2) screws.
12. Turn on AC line voltage supply.
JUNCTION BOX MOUNTING
1. See 1 and 3 above.
2. Knock out appropriate mounting hole in back of base (Figure 2).
3. Install gasket over mounting holes (Figure 1).
4. Mount back box to junction box ensuring gasket seal
5. See 7 –12 above.
Bolla WP Unit (BOL-WP)
OPERATION
1. To Test, depress the TEST Switch. Charge indicator will go out and the DC lamps will come on.
2. Release the TEST Switch. DC lamps will be extinguished, and the charge indicator will come on.
3. A bright charge indicator indicates a high charge rate. After the battery has reached full charge, the indicator light will
go out. Under normal operation the high charge indicator will turn off and on intermittently while the unit is in standby
mode (regular/mains AC present) since the charge rate will vary in order to maintain an optimal battery charge.
926000441 10/17/2019
Beghelli U.S.A., 3810 Executive Way, Miramar, Florida, Tel: (800) 726-4316 Tel: (954) 442-6600 Fax: (954) 442-6677
ITEM
LENS
1
LENS S2
BACK3
MOUN4
MR165
MR166
CHAR7
BATTE8
COVE9
2
2
3
3
4
4
A
B
C
D
This document is the property of and contains information proprietary to Beghelli Canad
purpose for which it was furnished and returned upon request. This document and such
otherwise in whole or in part without prior authorization of Beghelli Canda, Inc. The rece
agreement to the foregoing.
UNLESS OTHERWISE SPECIFIED
ALL DIMENSIONS = INCHES
ANGLES + 1/2
TOLERANCES:
.X = .020
.XX = .010
.XXX = .005
.XXXX = .003
3900 14Th. Avenue
Markham Ontario, L3R 4R3
Tel. # 905 948-9500 Fax # 905 948 867
email: sales@beghellicanada.com
Web: http://www.beghelli.com
DRAWN BY DATE
SIZE SCALE
DO NOT SCALE
3/4/201
PART #
L D
34
A
B
C
Parts List
DESCRIPTIONITEM
LENS
1
LENS SCREW2
BACK BOX3
MOUNTING GASKET4
MR16 LAMP5
MR16 LAMP HOLDER6
CHARGER BOARD7
BATTERY8
COVER9
1234
A A
B B
C C
D D
This document is the property of and contains information proprietary to Beghelli Canada, Inc. It is submitted in confidence and is to be used solely for the
purpose for which it was furnished and returned upon request. This document and such information is not to be reproduced, transmitted, disclosed, or used
otherwise in whole or in part without prior authorization of Beghelli Canda, Inc. The recepient's acceptance of this document shall be considered an
agreement to the foregoing.
UNLESS OTHERWISE SPECIFIED
ALL DIMENSIONS = INCHES
ANGLES + 1/2
TOLERANCES:
.X = .020
.XX = .010
.XXX = .005
.XXXX = .003
3900 14Th. Avenue
Markham Ontario, L3R 4R3
Tel. # 905 948-9500 Fax # 905 948 8673
email: sales@beghellicanada.com
Web: http://www.beghelli.com
MATERIAL
FINISH
DRAWN BY DATE
SIZE SCALE
REV
SHEET
PART NAME
DWG NO
REF NO
DO NOT SCALE
BOLLA UNIT INSTRUCTION SHEET
DRAWING
3/4/2015
PART #
L D
TROUBLESHOOTING
IMPORTANT NOTE: If the Time Delay optional feature is installed, emergency lamps will remain lit for up to
10 minutes following the resumption of regular/mains AC power to the unit.
EMERGENCY LAMPS DO NOT COME ON AT ALL, “AC ON” LED indicator is out before test...
Pilot Light is out before test...
1. Check AC supply - be sure unit has 24 hour AC supply (unswitched).
2. AC supply is OK, and indicator light is out, replace PC Board Assembly.
Pilot Light is on before test
1. Either the output is shorted or overloaded, or the battery is not connected.
2. Battery is severely discharged. Allow 48 hours for recharge and then retest. NOTE: This could be the result of a
switched AC supply to the unit (which has been turned off at some point), a battery with a shorted cell, an old
battery or a battery which has been discharged due to a long power outage and is not yet fully recharged.
EMERGENCY LAMPS COME ON DIM WHEN TEST SWITCH IS ACTIVATED
1 . Battery discharged - permit unit to charge for 48 hours and then retest. If lamps are still dim, check charger for
proper function. If charger functions correctly, replace battery.
EMERGENCY LAMPS COME ON WHEN BATTERY IS FIRST CONNECTED
1 . Battery may be connected in reverse polarity. Check connections. Connect Positive lead to Positive battery terminal
and Negative lead to Negative battery terminal. The lamps should then turn off and the charge indicator should light
when AC power is applied.
EMERGENCY LAMPS COME ON DIM WHEN AC POWER IS ON -
1 . Check supply voltage and AC connections. This emergency light is provided with brownout protection. The AC
supply must be at least 80% of nominal (96V on a 120V line) for equipment to function normally. At lower voltages the
emergency lamps will begin to glow dimly until the source voltage drops below the full “turn-on” point. NOTE: This
condition may also be caused by incorrectly connecting a 120 Volt supply line to the wrong voltage transformer lead.
SAVE THESE INSTRUCTIONS
MAINTENANCE
1. Beghelli strongly recommended compliance with all Code requirements.
2. Clean lenses on a regular basis.
NOTE: The servicing of any parts should be performed by qualified service personnel only. The use of replacement
parts not furnished by Beghelli may cause equipment failure and will void the warranty.
Figure 1 Figure 3
Figure 6
Figure 2
Figure 4
TEST
CHARGE
AC ON
WHITE - Neutral / Common
GREEN - Ground
BATTERY
NEG
-
POS
+
BATTERY+
BATTERY -
LAMP +
LAMP -
CHARGER PC BOARD
ASSEMBLY
LAMPS
STANDARD TRIPLE INPUT VERSION
RED - 347V Line / Hot
FUSE
CHARGER BOARD
BLACK - 120V Line / Hot
ORANGE - 277V Line / Hot Figure 5
1 Battery Unit
(+)( )
Black Red
Position the lamps as
needed
Battery
Lens
Parts List
DESCRIPTIONITEM
LENS
1
LENS SCREW2
BACK BOX3
MOUNTING GASKET4
MR16 LAMP5
MR16 LAMP HOLDER6
CHARGER BOARD7
BATTERY8
COVER9
1234
A
B
C
D
This document is the property of and contains information proprietary to Beghelli Canada, Inc. It is submitted in confidence and is to be used solely for the
purpose for which it was furnished and returned upon request. This document and such information is not to be reproduced, transmitted, disclosed, or used
otherwise in whole or in part without prior authorization of Beghelli Canda, Inc. The recepient's acceptance of this document shall be considered an
agreement to the foregoing.
UNLESS OTHERWISE SPECIFIED
ALL DIMENSIONS = INCHES
ANGLES + 1/2
TOLERANCES:
.X = .020
.XX = .010
.XXX = .005
.XXXX = .003
3900 14Th. Avenue
Markham Ontario, L3R 4R3
Tel. # 905 948-9500 Fax # 905 948 8673
email: sales@beghellicanada.com
Web: http://www.beghelli.com
MATERIAL
FINISH
DRAWN BY DATE
SIZE SCALE
REV
SHEET
PART NAME
DWG NO
REF NO
DO NOT SCALE
BOLLA UNIT INSTRUCTION SHEET
DRAWING
3/4/2015
PART #
L D
Screw
Knockout
Back box
Gasket
Knockout
Mounting Feet
Charger Board
926000441 10/17/2019
Beghelli U.S.A., 3810 Executive Way, Miramar, Florida, Tel: (800) 726-4316 Tel: (954) 442-6600 Fax: (954) 442-6677
/
