2. Wald
  3. BICYCLE BASKET

Wald BICYCLE BASKET Assembly Instructions

  • Hello! I've reviewed the user manual for the Wald Bicycle Basket 3133GB. This document details how to assemble the basket, including mounting it to the bicycle and attaching the basket to the mount. It also provides key safety warnings about overloading the basket. I'm ready to answer any questions you may have about its assembly or use.
  • How to remove the basket from holder?
    What is the warning about?
    What is the correct handle position to lock the basket?
LONG SCREW
2
MOUNTING
HOLDER
5
LOCK END
7
HOLDER SLOT
MOUNTING HOLDER
BOTTOM HOOKS
6
1
BRACE
HOLDER
TOP BRACKET
3
4
HANDLEBAR
CLAMP
SHORT SCREW
LONG SCREW
2
MOUNTING
HOLDER
5
LOCK END
7
HOLDER SLOT
MOUNTING HOLDER
BOTTOM HOOKS
6
1
BRACE
HOLDER
TOP BRACKET
3
4
HANDLEBAR
CLAMP
SHORT SCREW
LONG SCREW
2
MOUNTING
HOLDER
5
LOCK END
7
HOLDER SLOT
MOUNTING HOLDER
BOTTOM HOOKS
6
1
BRACE
HOLDER
TOP BRACKET
3
4
HANDLEBAR
CLAMP
SHORT SCREW
BICYCLE BASKET
with handle & mounting holder
- Basket easily removed for carrying
- Sized for grocery bag & many other uses
- Rust resistant durable finish
- Extended Mounting Holder allows clearance for shifters, brake
levers & cables
ASSEMBLY INSTRUCTIONS
- Loosely assemble
1
brace onto two vertical side wires of
2
holder with short screws. In most cases brace will be angled
upward toward Stem as shown.
- Center holder and hang
3
holder top brackets over handlebar.
(If clamping onto 7/8" portion of handlebar, insert rubber spacer
strips between holder and handlebar). Loosely assemble two
4
handlebar clamps with long screws.
- Attach basket to holder
- Hold basket so
5
lock end of handle is toward holder.
- Center basket with holder and insert lower basket frame wire over
bottom hooks of holder as shown.
- Raise handle upright and insert
5
lock end of handle through
7
slot at top of holder.
- Lay handle flat to lock.
- Adjust holder
1
brace vertically on holder side wires until basket
is in proper position.
- Remove basket from holder
- Raise basket handle upright.
- Pull away from holder and lift basket from bottom hooks of holder.
- Tighten all holder fittings securely.
Mfgr.No.3133
GB (Black)
Made in U.S.A. by Wald
C
2009 Wald LLC
Rev.A 4/8/2009
WARNING
DO NOT
overload basket.
Overloading basket may cause difficulty
in steering and/or loss of bicycle control
which could result in injury.
!
Mfgr.No.3133GB (Black)
Made in U.S.A. by Wald
C
2009 Wald LLC
Rev.A 4/8/2009
WARNING
DO NOT
overload basket.
Overloading basket may cause difficulty
in steering and/or loss of bicycle control
which could result in injury.
!
- Loosely assemble
1
brace onto two vertical side wires of
2
holder with short screws. In most cases brace will be angled
upward toward Stem as shown.
- Center holder and hang
3
holder top brackets over handlebar.
(If clamping onto 7/8" portion of handlebar, insert rubber spacer
strips between holder and handlebar). Loosely assemble two
4
handlebar clamps with long screws.
- Attach basket to holder
- Hold basket so
5
lock end of handle is toward holder.
- Center basket with holder and insert lower basket frame wire over
bottom hooks of holder as shown.
- Raise handle upright and insert
5
lock end of handle through
7
slot at top of holder.
- Lay handle flat to lock.
- Adjust holder
1
brace vertically on holder side wires until basket
is in proper position.
- Remove basket from holder
- Raise basket handle upright.
- Pull away from holder and lift basket from bottom hooks of holder.
- Tighten all holder fittings securely.
ASSEMBLY INSTRUCTIONS
- Basket easily removed for carrying
- Sized for grocery bag & many other uses
- Rust resistant durable finish
- Extended Mounting Holder allows clearance for shifters, brake
levers & cables
BICYCLE BASKET
with handle & mounting holder
Mfgr.No.3133GB (Black)
Made in U.S.A. by Wald
C
2009 Wald LLC
Rev.A 4/8/2009
WARNING
DO NOT
overload basket.
Overloading basket may cause difficulty
in steering and/or loss of bicycle control
which could result in injury.
!
- Loosely assemble
1
brace onto two vertical side wires of
2
holder with short screws. In most cases brace will be angled
upward toward Stem as shown.
- Center holder and hang
3
holder top brackets over handlebar.
(If clamping onto 7/8" portion of handlebar, insert rubber spacer
strips between holder and handlebar). Loosely assemble two
4
handlebar clamps with long screws.
- Attach basket to holder
- Hold basket so
5
lock end of handle is toward holder.
- Center basket with holder and insert lower basket frame wire over
bottom hooks of holder as shown.
- Raise handle upright and insert
5
lock end of handle through
7
slot at top of holder.
- Lay handle flat to lock.
- Adjust holder
1
brace vertically on holder side wires until basket
is in proper position.
- Remove basket from holder
- Raise basket handle upright.
- Pull away from holder and lift basket from bottom hooks of holder.
- Tighten all holder fittings securely.
ASSEMBLY INSTRUCTIONS
- Basket easily removed for carrying
- Sized for grocery bag & many other uses
- Rust resistant durable finish
- Extended Mounting Holder allows clearance for shifters, brake
levers & cables
BICYCLE BASKET
with handle & mounting holder
A
WALD LLC MAYSVILLE, KY.
DRN
TITLE
APVD
SCALE
DATE
NO.
REVISIONS
ZONE
REV
DESCRIPTION
BY
DATE
CHAD
3133GB BASKET -
ASSEMBLY INSTRUCTIONS
1:1
9-15-03
C-68019
A
B
C
D
E
F
A
B
C
D
E
F
1
2
3
4
5
6
1
2
3
4
5
6
A
CHAD
4-8-09
REVISED WARNING NOTE - S.V.P.
/