2. ML Accessories
  3. OS0014

ML Accessories OS0014, OS0014B User manual

  • Hello! I've reviewed the Installation & Maintenance Manual for the Knightsbridge OS0014 and OS0014B motion sensors. This document covers safety, installation, wiring, setup, and maintenance of the devices, including specific details on time and lux adjustments. I'm ready to answer your questions about these motion sensors.
  • What is the recommended installation height?
    What is the IP rating of this sensor?
    What is the maximum detection range?
    What are the available adjustments for the sensor?
116
INSTALLATION & MAINTENANCE MANUAL
OS0014 & OS0014B
IP
44
230V
50Hz
1
These instructions should be read carefully and retained after installation by the end user for future
reference and maintenance.
These instructions should be used to aid installation of the following products:
OS0014, OS0014B
GENERAL INSTRUCTIONS
SAFETY
INSTALLATION
• Installation of this sensor should only be carried out by a qualified electrician or competent person
to the latest Building and current IEE Wiring Regulations (BS7671)
• Please isolate mains prior to installation/maintenance
• Check the total load on the circuit does not exceed the rating of the circuit cable, fuse or circuit
breaker
• Please note the IP (Ingress of Protection) rating of this sensor when deciding the location for
installation
• This product is Class II double insulated
• This product is IP44 rated
• Provide power to the required point of installation. Suitable IP rated junction boxes should be
used where required
• We recommend an installation height of between 1.8m and 2.5m
• Remove the back cover by removing screw (see Fig 1) to access the terminal block
• Using the back cover as a template, mark the location of the fixing holes and drill the holes
ensuring not to infringe with any joists, gas or water pipes or electrical cables
• Connect the sensor to the luminaire and mains supply (via terminal connector) ensuring the
correct polarity is observed. See Fig 2 for the wiring diagram (Live (brown), Neutral (blue) and
Switched Live (A)
Fig 1
Remove screw
2
SENSOR SETUP
DETECTION DIAGRAM
• Please see Fig 3 for sensor adjustments
• Replace back cover
• Switch on power supply and check for correct operation
Fig 2
Fig 3
OS0014series
Theseinstructionsshouldbereadcarefullyandretainedafterinstallationbytheenduserforfuturereferenceand
maintenance.
Theseinstructionsshouldbeusedtoaidinstallationofthefollowingproducts:
OS0014,OS0014B
SAFETY
• Installationofthissensorshouldonlybecarriedoutbyaqualifiedelectricianorcompetentpersontothe
latestBuildingandcurrentIEEWiringRegulations(BS7671)
• Pleaseisolatemainspriortoinstallation/maintenance
• Checkthetotalloadonthecircuit(includingwhenthisluminaireisfitted)doesnotexceedtheratingofthe
circuitcable,fuseorcircuitbreaker
• PleasenotetheIP(IngressofProtection)ratingofthisluminairewhendecidingthelocationforinstallation
• ThisproductisClassIIdoubleinsulated
• ThisproductisIP44rated
INSTALLATION
• Providepowertotherequiredpointofinstallation.SuitableIPratedjunctionboxesshouldbeusedwhere
required
• Werecommendaninstallationheightofbetween1.8mand2.5m
• Removethebackcoverbyremovingscrew,(seeFig1)toaccesstheterminalblock
Fig1
• Usingthesensorasatemplatemarkthelocationofthefixingholes,anddrilltheholesensuringnottoinfringe
withanyjoists,gasorwaterpipesorelectricalcables
• Connectthesensortotheluminaireandmainssupply(viaterminalconnector)ensuringthecorrectpolarityis
observed.SeeFig2forthewiringdiagram(Live(brown),Neutral(blue)andSwitchedLive(A))
Fig2
• PleaseseeFig3forsensoradjustments
• Replacebackcover
• Switchonpowersupplyandcheckforcorrectoperation
Removescrew
(N)Neutral(blue)
(L)Live(brown)
N
A
L
luminaire
(A)Red
Time
Lux
SENSORSETUP
Fig3
DETECTIONDIAGRAM
WARNING
Thisproductmustbedisconnectedfromthecircuitifsubjectedtoanyhighvoltageorinsulationresistancetesting.
Irreparabledamagewilloccurifthisinstructionisnotfollowed.
GENERAL
Theunitshouldberecycledinthecorrectmannerwhenitreachestheendofitslife.Checklocalauthoritiesforwhere
facilitiesexist.
Cleanwithasoftdryclothonly,donotuseaggressivecleaningproductsorsolventswhichmaydamagethesensor.
Warranty
Thisproducthasawarrantyof1yearfromdateofpurchase.Failuretoinstallthisproductinaccordancewiththecurrent
editionoftheIEEWiringRegulations,improperuse,orremovalofthebatchcodeswillinvalidatethewarranty.Ifthis
productshouldfailwithinitswarrantyperioditshouldbereturnedtotheplaceofpurchaseforafreeofcharge
replacement.MLAccessoriesdoesnotacceptresponsibilityforanyinstallationcostsassociatedwiththereplacement
product.Yourstatutoryrightsarenotaffected.MLAccessoriesreservetherighttoalterproductspecificationwithoutprior
notice.
Mountingheight
1.8m-2.5m
-
+
Min10sec
+3sec
Max15min
3min
3lx
2000lx
Lux
Time
up to 12m
Floor
Wall
3
SENSORSETUP
Fig3
DETECTIONDIAGRAM
WARNING
Thisproductmustbedisconnectedfromthecircuitifsubjectedtoanyhighvoltageorinsulationresistancetesting.
Irreparabledamagewilloccurifthisinstructionisnotfollowed.
GENERAL
Theunitshouldberecycledinthecorrectmannerwhenitreachestheendofitslife.Checklocalauthoritiesforwhere
facilitiesexist.
Cleanwithasoftdryclothonly,donotuseaggressivecleaningproductsorsolventswhichmaydamagethesensor.
Warranty
Thisproducthasawarrantyof1yearfromdateofpurchase.Failuretoinstallthisproductinaccordancewiththecurrent
editionoftheIEEWiringRegulations,improperuse,orremovalofthebatchcodeswillinvalidatethewarranty.Ifthis
productshouldfailwithinitswarrantyperioditshouldbereturnedtotheplaceofpurchaseforafreeofcharge
replacement.MLAccessoriesdoesnotacceptresponsibilityforanyinstallationcostsassociatedwiththereplacement
product.Yourstatutoryrightsarenotaffected.MLAccessoriesreservetherighttoalterproductspecificationwithoutprior
notice.
Mountingheight
1.8m-2.5m
-
+
Min10sec
+3sec
Max15min
3min
3lx
2000lx
Lux
Time
up to 12m
Floor
Wall
±
This product must be disconnected from the circuit if subjected to any high voltage or insulation
resistance testing. Irreparable damage will occur if this instruction is not followed.
The unit should be recycled in the correct manner when it reaches the end of its life. Check local
authorities for where facilities exist.
Clean with a soft dry cloth only, do not use aggressive cleaning products or solvents which may
damage the sensor.
This product has a warranty of 1 year from date of purchase. Failure to install this product in
accordance with the current edition of the IEE Wiring Regulations, improper use, or removal of
the batch codes will invalidate the warranty. If this product should fail within its warranty period it
should be returned to the place of purchase for a free of charge replacement. ML Accessories does
not accept responsibility for any installation costs associated with the replacement product. Your
statutory rights are not affected. ML Accessories reserve the right to alter product specification
without prior notice.
WARNING
GENERAL
WARRANTY
4
ML Accessories Limited
LU5 5TA
www.mlaccessories.co.uk SBOCT16_V2
5
/