Tripp Lite SU3000XLNAFTA Owner's manual

Category
Uninterruptible power supplies (UPSs)
Type
Owner's manual

Tripp Lite SU3000XLNAFTA is a SmartOnline UPS system designed to protect sensitive electronic equipment from power disturbances and outages. It provides reliable backup power, surge protection, and advanced power management features to keep your devices running smoothly. With its true on-line operation, the SU3000XLNAFTA continuously filters and regulates incoming AC power, ensuring a consistent and clean power supply to connected equipment. It also features an automatic self-test function to ensure reliable performance and early detection of potential problems.

Tripp Lite SU3000XLNAFTA is a SmartOnline UPS system designed to protect sensitive electronic equipment from power disturbances and outages. It provides reliable backup power, surge protection, and advanced power management features to keep your devices running smoothly. With its true on-line operation, the SU3000XLNAFTA continuously filters and regulates incoming AC power, ensuring a consistent and clean power supply to connected equipment. It also features an automatic self-test function to ensure reliable performance and early detection of potential problems.

Owner’s Manual
1111 W. 35th Street, Chicago, IL 60609 USA
773.869.1234 (USA) • 773.869.1212 (International)
www.tripplite.com
Important Safety Instructions
2
Installation
3
Basic Operation
5
Battery Replacement
11
Storage and Service
11
SmartOnline
True On-Line Tower UPS Systems
Warranty Registration
12
Español
Français
25
13
Copyright ©2009 Tripp Lite. All rights reserved. SmartOnline
is a trademark of Tripp Lite.
Troubleshooting
9
Warranty
Registration:
register online today for a chance
to win a FREE Tripp Lite product—
www.tripplite.com/warranty
Not suitable for mobile applications.
200903102 93-2470.indd 1 4/1/2009 3:56:09 PM
2
UPS Location Warnings
• InstallyourUPSindoors,awayfromexcessmoistureorheat,conductivecontaminants,
dustordirectsunlight.
• Forbestperformance,keeptheindoortemperaturebetween32ºFand104ºF(0ºCand
40ºC).
• LeaveadequatespacearoundallsidesoftheUPSforproperventilation.
• Donotmountunitwithitsfrontorrearpanelfacingdown(atanyangle).
Mountinginthismannerwillseriouslyinhibittheunit’sinternalcooling,eventually
causingproductdamagenotcoveredunderwarranty.
UPS Connection Warnings
• ConnectyourUPSdirectlytoaproperlygroundedACpoweroutlet.Donotplugthe
UPSintoitself;thiswilldamagetheUPS.
• DonotmodifytheUPS'splug,anddonotuseanadapterthatwouldeliminatetheUPS’s
groundconnection.
• DonotuseextensioncordstoconnecttheUPStoanACoutlet.Yourwarrantywillbe
voidedifanythingotherthanTrippLitesurgesuppressorsareusedtoconnectyourUPS
to an outlet.
• IftheUPSreceivespowerfromamotor-poweredACgenerator,thegeneratormust
provideclean,filtered,computer-gradeoutput.
Equipment Connection Warnings
• Useofthisequipmentinlifesupportapplicationswherefailureofthisequipmentcan
reasonablybeexpectedtocausethefailureofthelifesupportequipmentorto
significantlyaffectitssafetyoreffectivenessisnotrecommended.Donotusethis
equipmentinthepresenceofaflammableanestheticmixturewithair,oxygenornitrous
oxide.
• DonotconnectsurgesuppressorsorextensioncordstotheoutputofyourUPS.This
mightdamagetheUPSandwillvoidthesurgesuppressorandUPSwarranties.
Battery Warnings
Batteriescanpresentariskofelectricalshockandburnfromhighshort-circuitcurrent.
Observeproperprecautions.Donotdisposeofthebatteriesinafire.DonotopentheUPS
orbatteries.Donotshortorbridgethebatteryterminalswithanyobject.Unplugandturn
offtheUPSbeforeperformingbatteryreplacement.Usetoolswithinsulatedhandles.
Therearenouser-serviceablepartsinsidetheUPS.Batteryreplacementshouldbe
performedonlybyauthorizedservicepersonnelusingthesamenumberandtypeof
batteries(SealedLead-Acid).Thebatteriesarerecyclable.Refertoyourlocalcodesfor
disposalrequirementsorintheUSAonlycall1-800-SAV-LEADor1-800-8-BATTERY
(1-800-822-8837)orvisitwww.rbrc.comforrecyclinginformation.TrippLiteoffersa
completelineofUPSSystemReplacementBatteryCartridges(R.B.C.).VisitTrippLiteon
theWebatwww.tripplite.com/support/battery/index.cfmtolocatethespecificreplacement
batteryforyourUPS.
SAVE THESE INSTRUCTIONS
This manual contains instructions and warnings that should be followed during the
installation,operationandstorageofallTrippLiteUPSSystems.Failuretoheedthese
warningswillvoidyourwarranty.
2
Important Safety Instructions
200903102 93-2470.indd 2 4/1/2009 3:56:09 PM
1
2
3
1
33
Important Safety Instructions
Connection and Start-Up
Plug your UPS’s line cord into an
electrical outlet.
Your UPS must be connected to a dedicated
circuitofsufficientamperage.Note,however,
that the select models may be fitted with
differentplugtypes.Refertothe“OPRating/
PlugRating”chartprintedonthetopofyour
UPS.
OnceyourUPSispluggedin,thefanandall
IndicatorLightswillturnON.The“LINE”and
“LOADACTIVEMETER”LEDswillilluminate
andtheUPSwillemitabeeptoindicatenormal
operation.However, powerisnot supplied to
your UPS’sACoutletsuntiltheUPSisturned
on.
Plug your equipment into your UPS.
Your UPS is designed to support computer
equipmentonly.YouwilloverloadyourUPSif
you connect household appliances or laser
printerstotheUPS'soutlets.
Turn your UPS ON:
• Pressthe“ON/TEST”Button
• Holditforseveralsecondsuntilyou
hearabeep
• Releaseit
Your UPS will begin providing AC power to its outlets.
The “ON LINE” LED will illuminate.
Your UPS will function properly without these
connections.
Phone Line or Phone/Network
Line Surge Suppression
Your UPS has jacks which protect against
surges on a phone or network line.* Using
appropriate network cords connect your wall
jack to the UPS jack marked “IN.” Connect
your equipment to the UPS jack marked
“OUT.”Makesuretheequipmentyouconnect
to the UPS's jacks is also protected against
surgesontheACline.
*NotcompatiblewithPoE(PowerOverEthernet)applications.
Your model may differ.
1
2
3
Your model
may differ.
Installation
Optional Connections
1
Your model may differ.
200903102 93-2470.indd 3 4/1/2009 3:56:10 PM
2b
4
2a
3a
4-5
3b
44
Optional Connections (continued)
USB and RS-232 Serial
Communications
Usethe includedUSB cable(see
2a
)and/or
DB9 serial cable (see
2b
) to connect the
communication port of yourcomputer to the
communication port of your UPS. Install on
your computer the Tripp Lite PowerAlert
Software appropriate to your computer's
operatingsystem.
EPO Port Connection
WhentheUPSisconnectedtothiscircuit,it
enables emergency shutdown of the UPS's
inverter.Usingthecableprovided,connectthe
EPO port of your UPS (see
3a
) to a user-
supplied normally closed or normally open
switch according to the circuit diagram (see
3b
).TheEPOportisnotaphonelinesurge
suppressor;donotconnectaphonelineto
thisport.
External Battery Connection
Checktoensurethattheexternalbatteriesyou
areconnectingmatchthevoltagelistedonyour
UPS's battery connector. Adding external
batterieswillincreaserechargetimeaswellas
runtime.Seethebatterypackowner'smanual
for complete installation instructions. Make
sure cables are fully inserted into their
connectors. Small sparks may result during
battery connection; this is normal. Do not
connectordisconnectbatterypackswhenthe
UPSisrunningonbatterypower.
2
3
Your model
may differ.
Your model
may differ.
Installation (continued)
4
Your model
may differ.
Your model
may differ.
200903102 93-2470.indd 4 4/1/2009 3:56:12 PM
55
Front Panel Switches
“ON/TEST” Button: This switch controls four separate UPS
functions:
UPSPowerON
ToturntheUPSon,pressthisbutton,holditforseveralsecondsuntil
you hear a beep, then release it. The “ON LINE” LED will
illuminate.
UPSSelf-Test
Duringnormalon-lineoperation,pressthisbuttonandholdituntil
youhearabeep.Thisinitiatesa10-secondself-testofthebattery.The
UPS will shift to battery power (all LEDs will illuminate) for ten
seconds.
AlarmSilence
TosilencetheUPS“on-battery”alarm,pressthisbuttonandholdit
untilyouhearabeep.
UPSColdStart
TouseyourUPSasastand-alonepowersourcewhenACpoweris
unavailable(i.e.duringablackout),pressthisbuttonandholdituntil
you hear a beep. The UPS will then provide battery power to its
outlets.*
* The “ON BATT” Indicator Light will be illuminated since your UPS will be operating
from battery power.
“OFF”Button:ThisbuttonturnspowerOFFattheUPSreceptacles.
Pressthisswitch,holdituntilyouhearabeep,thenreleaseit.The
UPSwillcontinuechargingandthefanwillcontinuetocoolinternal
componentsevenafteryouturntheUPSreceptaclesoff.Toturnthe
UPS OFF completely, including the charger, disconnecttheUPS’s
powercordafterpressingthe“OFF”switch.
“ONLINE”LED:Thisgreenlightwillilluminateconstantlytoindicate
the UPS is performing normal on-line operation (filtering and
resynthesizingincomingAClinevoltagetoprovidepuresinewave
output).Whenthislightisilluminated,youcanmonitortheloadlevel
ofyourUPSonthe“LOADACTIVEMETER”LEDs.
“LINE”LED:Thisgreenlightwillilluminateconstantlytoindicate
theutilitysuppliedAClinevoltageatyourwalloutletisnominal.It
willflashifthelinevoltageisoutsidethenominalrange(eithertoo
lowortwohigh).NoactionisrequiredonyourpartwhentheLED
flashes; the UPS continuously and automatically filters AC line
power to provide your equipment with pure sine waveACpower,
regardlessofbrownoutorovervoltageconditions.Ifthislightisoff,
thenAClinevoltageisnotpresent(blackout)orisatanextremely
high voltage,andtheUPSwillprovideconnectedequipmentwith
powerfrombattery.
Front Panel Indicator Lights
Basic Operation
200903102 93-2470.indd 5 4/1/2009 3:56:12 PM
66
Front Panel Indicator Lights continued
“BYPASS”LED:ThisyellowlightwillflashtoindicatethattheDC/
AC inverter is deactivated and the UPS is in the “Bypass” mode.
DuringnormaloperationthisLEDwilllightbrieflywhentheunitis
pluggedin,butifaninternalfaultoroverloadoccursthislightwill
flash constantly and the fault LED will illuminate to show that
connectedequipmentwillreceivefilteredACmainspower,butwill
notreceivebatterypowerduringablackout.Inthiscase,contactTripp
Lite for service. If the UPS has been placed into Economy Mode
(available on select UPS systems), it configures an online UPS to
functionasaswitchingUPS.WhentheUPSsystemisinEconomy
Mode,itoperatesatincreased efficiency whileACutilitypower is
available(within+/-10%nominal)andswitchestobatterypowerif
AC utility power is interrupted. The yellow “BYPASS” LED will
remain on when the UPSsystem is in Economy Mode.(Formore
informationonhowtoaccesstheEconomyMode,pleaserefertothe
PowerAlertsoftwareUser’sManual.)
“FAULT”LED(selectmodelsonly):Thisredlightwillflashwhen
yourUPSdetectsaninternalfault(overheating,overvoltages,etc.)or
whenitdetectsawiring fault inyourwalloutlet (reversedphases,
missingground,etc.)TheUPSwillonlydetectwiringfaultswhenit
ispluggedintoautilityoutletbutnotturnedON.Ifthelightpersists
afterrestartingtheUPS,contactanelectriciantochecktheACline.
Your UPS will identify the presence of most (but not all) wiring
faults.
“LOADACTIVEMETER”LED:Thisgreenlightwillilluminate
whenyourUPSisreceivingACpowertoindicatethatthesetoffour
dual-functionLEDsisdisplayingtheloadlevelofyourUPS.
“BATTACTIVE METER”LED:Thisgreen lightwillilluminate
whenyourUPSisoperatingfrombatterypowertoindicatethatthe
setoffourdual-functionLEDsisdisplayingthebatterychargelevel
ofyourUPS.Note:the“ONBATT”LEDwillalsobeilluminated.
“OVERLOAD”LED:Thisredlightwillilluminateconstantlytoindicate
thatyourUPS’scapacityhasbeenexceededwhileitisinon-lineoperation.
TheUPSalarmwillbeepcontinuously.Immediatelyremoveoverload
untillightandalarmgoesoff.Ifyoudonotimmediatelyremovethe
overload,theUPSwilltransferfromon-linetobypassoperation.
“BATTLOW”LED:ThisyellowlightwillilluminatewhenyourUPS’s
batterychargelevelislow.TheUPSalarmwillbeepuntileitherthe
batterychargeisdepletedorthebatteriesareadequatelyrecharged.
Basic Operation (continued)
200903102 93-2470.indd 6 4/1/2009 3:56:13 PM
77
Rear Panel
“ON BATT” LED: This green light will illuminate constantly to
indicatethatAClinevoltageisnotpresentandyourUPSisproviding
yourequipmentwith batterypower.TheUPS willalsobeep every
twoseconds,unlesssilencedbythe“ON/TEST”Button.Whenthis
lightisilluminated,youcanmonitorthebatterychargelevelofyour
UPSonthe“BATTACTIVEMETER”LEDs.
“REPLACE BATT” LED:Thisredlightwill illuminate constantly
and the UPS alarm will beep every 2 seconds if your UPS’s
microprocessor detects a battery fault or if your UPS fails the
automaticself-test(afteryouturnyourUPSON)andtheUPSbattery
islessthanfullycharged.LettheUPSsystemchargeforatleast12
hoursandperformaselftestusingthe“ON/TESTButton”.Ifthelight
continuestostayon,contactTrippLiteforservice.
AccessorySlot:Removethesmallcoverpanelfromthisslottouse
optional accessories to remotely monitor and control your UPS.
Contact Tripp Lite Customer Support at (773) 869-1234 for more
information,includingalistofavailableSNMP,networkmanagement
andconnectivityproducts.
ExternalBatteryPackConnector(configurationvariesbymodel):
Use to connect optional Tripp Lite Battery Packs for additional
runtime.ContactTrippLiteCustomerSupportat(773)869-1234for
theappropriateTrippLitebatterypacktoconnect.Refertoinstructions
availablewiththeBatteryPackforcompleteconnectioninformation
andsafetywarnings.
Fan:ThefancoolstheUPS’sinternalcomponents.Itisalwayson
whenlinepowerispresent.
InputCircuitBreakerSwitch:Thisresettablebreakerpreventshigh
input current from damaging the UPS or the attached load. If this
breakertrips,makesureyourUPSisconnectedtoACpowerofthe
proper voltage before resetting the circuit breaker by pushing the
breakerswitchin.
InputCord:This permanentlyattachedpowercordconnectsyour
UPStoapoweroutlet.
Front Panel Indicator Lights continued
Basic Operation (continued)
200903102 93-2470.indd 7 4/1/2009 3:56:14 PM
8
Rear Panel
continued
AC Receptacles (Varied by Model): These 15-, 20- and 30-amp
receptaclesprovideyourconnectedequipment withpuresine-wave
ACoutputfromtheAClineduringnormaloperationandfrombattery
power during blackouts and severe brownouts. Power provided at
these outlets is filtered to protect connected equipment against
damaging surges and line noise. The receptacles are divided into
numbered load banks, as labelled on the unit. Using PowerAlert
softwareandcabling, load banks oneandtwomaybeindividually
turnedoffandonfromaremotelocation,allowinguserstoresetor
rebootconnectedequipment.
Telephone/Network Protection Jacks: These jacks protect your
equipment against surges over a telephone/network data line.
Connectingyourequipmenttothesejacksisoptional.YourUPSwill
workproperlywithoutthisconnection.Not compatible with PoE (Power Over
Ethernet) applications.
CommunicationsPorts(USBorRS-232):Theseportsconnectyour
UPStoanyworkstationorserver.UsewithTrippLite’sPowerAlert
Softwareandincludedcablestoenableyourcomputertoautomatically
saveopenfilesandshutdownequipmentduringablackout.Alsouse
PowerAlertSoftwaretomonitorawidevarietyofAClinepowerand
UPSoperatingconditions.ConsultyourPowerAlertSoftwaremanual
or contact Tripp Lite Customer Support formore information. See
“USB and RS-232 Serial Communications” in the “Optional
Connections”sectionforinstallationinstructions.
Dry contact communications are simple, but some knowledge of
electronics is necessary to configure them. The DB9 port's pin
assignmentsareshowninthediagram.IftheUPSbatteryislow,the
UPSsendsasignalbybridgingpins1and5.Ifutilitypowerfails,the
UPSsendsasignalbybridgingpins8and5.ToshuttheUPSdown
remotely,shortpin3~pin9foratleast3.8seconds.
EPO(EmergencyPowerOff)Port:YourUPSfeaturesaEPOport
thatmaybeusedtoconnecttheUPStoacontactclosureswitchto
enableemergencyinvertershutdown.SeeOptionalInstallation.
NEMA 5-15R
NEMA 5-15/20R
Other outlet types not shown
Communications
8
Basic Operation (continued)
200903102 93-2470.indd 8 4/1/2009 3:56:14 PM
99
TheUPS’scontrolpanellightswillturnoninthesequencesbelowtosignalthattheUPSis
havingoperationaldifficulties.
Lights (On/Flashing) and Condition Solution
On: REPLACE BATT Let the UPS system charge for at least
Condition: Replace Battery 12 hours and perform a self test using
the "ON/Test Switch". If the light
continues to stay on, contact Tripp Lite
for service.
On: BATT LOW, ON BATT Prepare for imminent UPS shutdown.
Condition: Battery Low
On: BYPASS, LINE, LOAD, OVERLOAD Reduce the load the UPS supports.
Condition: On Bypass due to Overload
Flashing: OVERLOAD Remove the cause of the short circuit
Condition: Short Circuit from the UPS output.
On: FAULT Check the utility line for wiring problems
Condition: Wiring Fault such as reversed line and neutral or a
missing ground.
On: FAULT, 100% Restart the UPS. If the problem persists,
Condition: Battery Voltage too High contact Tripp Lite for repairs.
On: FAULT, BYPASS, LINE, 50% Restart the UPS. If the problem persists,
Condition: On Bypass due to contact Tripp Lite for repairs.
High Output Voltage
On: FAULT, BYPASS, LINE Restart the UPS. If the problem persists,
Flashing: 50% contact Tripp Lite for repairs.
Condition: On Bypass due to
Low Output Voltage
On: FAULT, BYPASS, LINE, 25% Restart the UPS. If the problem persists,
Condition: On Bypass due to High contact Tripp Lite for repairs.
Bus Voltage
On: FAULT, BYPASS, LINE Restart the UPS. If the problem persists,
Flashing: 25% contact Tripp Lite for repairs.
Condition: On Bypass due to Low
Bus Voltage
Troubleshooting
200903102 93-2470.indd 9 4/1/2009 3:56:14 PM
10
Troubleshooting (continued)
Lights (On/Flashing) and Condition Solution
On: BYPASS, LINE Check the UPS to be sure that there is
Flashing: FAULT adequate space for air to circulate near
Condition: On Bypass due to High the vents and that the fan is working
Internal Temperature properly. Restart the UPS.
Flashing: LINE This indicates that utility power is too high
Condition: Input Abnormal or low for the UPS to operate in BYPASS
mode, so if an inverter failure occurs,
the UPS will deliver no output.
On: FAULT, 50% Restart the UPS. If the problem persists,
Flashing: LINE contact Tripp Lite for repairs.
Condition: No Output due to High
Output Voltage and Abnormal Input
On: FAULT
Restart the UPS. If the problem persists,
Flashing: LINE, 50% contact Tripp Lite for repairs.
Condition: No Output due to Low
Output Voltage and Abnormal Input
On: FAULT, 25% Restart the UPS. If the problem persists,
Flashing: LINE contact Tripp Lite for repairs.
Condition: No Output due to High
Bus Voltage and Abnormal Input
On: FAULT Restart the UPS. If the problem persists,
Flashing: LINE, 25% contact Tripp Lite for repairs.
Condition: No Output due to Low
Bus Voltage and Abnormal Input
Flashing: LINE, FAULT Check the UPS to be sure that there is
Condition: No Output due to High adequate space for air to circulate near
Internal Temperature and Abnormal the vents and that the fan is working
Input properly. Restart the UPS. If the problem
persists, contact Tripp Lite for repairs.
10
200903102 93-2470.indd 10 4/1/2009 3:56:14 PM
1
2
3
1111
Battery Replacement Door: Under normal conditions, the original
batteryinyourUPSwilllastseveralyears.Batteryreplacementshouldbe
performedonlybyqualifiedservicepersonnel.Referto“BatteryWarnings”
intheSafetysection.ShouldyourUPSrequirebatteryreplacement,visit
TrippLiteontheWebatwww.tripplite.com/support/battery/index.cfmto
locatethespecificreplacementbatteryforyourUPS.
Carefully pull the front panel away from the UPS.
Placefrontpanelontopoftheunit.Removethebatterysupportbar.
Remove old batteries.
CarefullypullthebatteriesfromtheUPSanddisconnectthem.
Connect new batteries.
Connectthenewbatteriesin exactlythe samemannerasthe old
ones: positive (red) connectors together and negative (black)
connectorstogether.CarefullypushbatteriesbackintotheUPS.
Reassemble UPS.
Reinstallthebatterysupportbarandreplacethefrontpanel.
1
2
3
4
Battery Replacement
Your model may differ.
Your model may differ.
Your model may differ.
Storage and Service
FirstturnyourUPSOFF:pressthe“OFF”switchtoturnpoweroffattheUPSoutlets,then
disconnectthepowercordfromthewalloutlet.Next,disconnectallequipmenttoavoidbattery
drain.IfyouplanonstoringyourUPSforanextendedperiodoftime,fullyrechargetheUPS
batteriesonceeverythreemonthsbypluggingtheUPSintoaliveACoutletandlettingtheUPS
chargefor4-6hours.IfyouleaveyourUPSbatteriesdischargedforanextendedperiodoftime,
theymaysufferpermanentlossofcapacity.
Before returning your UPS for service, follow these steps: 1. Review the installation and
operationinstructionsinthismanualtoensurethattheserviceproblemdoesnotoriginatefrom
amisreadingoftheinstructions.2.Iftheproblemcontinues,donotcontactorreturntheUPS
tothedealer.Instead,callTrippLiteat(773)869-1233.Aservicetechnicianwillaskforthe
UPS'smodelnumber,serialnumberandpurchasedateandwillattempttocorrecttheproblem
overthephone.3.Iftheproblemrequiresservice,thetechnicianwillissueyouaReturned
MaterialAuthorization(RMA)number,whichisrequiredforservice.Ifyourequirepackaging,
the technician can arrange to send you properpackaging.Securely pack the UPS to avoid
damageduringshipping. DonotuseStyrofoambeadsforpackaging.Anydamages(direct,
indirect,special,incidentalorconsequential)totheUPSincurredduringshipmenttoTrippLite
oranauthorizedTrippLiteservicecenterisnotcoveredunderwarranty.UPSSystemsshipped
to Tripp Lite or an authorized Tripp Lite service center must have transportation charges
prepaid.MarktheRMAnumberontheoutsideofthepackage.IftheUPSSystemiswithinthe
2-yearwarrantyperiod,encloseacopyofyoursalesreceipt.ReturntheUPSforserviceusing
aninsuredcarriertotheaddressgiventoyoubytheTrippLiteservicetechnician.
Storage
Service
200903102 93-2470.indd 11 4/1/2009 3:56:30 PM
12
Visit www.tripplite.com/warranty today to register the warranty for your new Tripp Lite product. You'll be automatically entered into a drawing for a chance to
win a FREE Tripp Lite product!* * No purchase necessary. Void where prohibited. Some restrictions apply. See website for details.
Regulatory Compliance Identification Numbers: For the purpose of regulatory compliance certifications and identification, your Tripp Lite product has been
assigned a unique series number. The series number can be found on the product nameplate label, along with all required approval markings and information.
When requesting compliance information for this product, always refer to the series number. The series number should not be confused with the marking
name or model number of the product.
FCC Specifications for Models with FCC Approval: This device complies with part 15 of the FCC Rules. Operation is subject to the following two
conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may
cause undesired operation.
Models compliant with limits for Class A digital device: This equipment has been tested and found to comply with the limits for a Class A digital device,
pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is
operated in a commercial environment. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance
with the instruction manual, may cause harmful interference to radio communications. Operation of this equipment in a residential area is likely to cause
harmful interference in which case the user will be required to correct the interference at his own expense. The user must use shielded cables and connectors
with this product. Any changes or modifications to this product not expressly approved by the party responsible for compliance could void the user’s authority
to operate the equipment.
Models compliant with limits for Class B digital device: This equipment has been tested and found to comply with the limits for a Class B digital device,
pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation.
This equipment generates, uses and can radiate radio frequency energy, and if not installed and used in accordance with the instruction manual, may cause
interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause
harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct
the interference using one or more of the following measures: reorient or relocate the receiving antenna; increase the separation between the equipment and
the receiver; connect the equipment into an outlet on a circuit different from that which the receiver is connected; consult the dealer or an experienced radio/
television technician for help. The user must use shielded cables and connectors with this product. Any changes or modifications to this product not expressly
approved by the party responsible for compliance could void the user's authority to operate the equipment.
FCC Part 68 Notice (United States Only): If your Modem/Fax Protection causes harm to the telephone network, the telephone company may temporarily
discontinue your service. If possible, they will notify you in advance. If advance notice isn't practical, you will be notified as soon as possible. You will be
advised of your right to file a complaint with the FCC. Your telephone company may make changes in its facilities, equipment, operations or procedures that
could affect the proper operation of your equipment. If it does, you will be given advance notice to give you an opportunity to maintain uninterrupted service.
If you experience trouble with this equipment's Modem/Fax Protection, please call Tripp Lite Technical Support at (773) 869-1234 for repair/warranty
information. The telephone company may ask you to disconnect this equipment from the network until the problem has been corrected or you are sure the
equipment is not malfunctioning. There are no repairs that can be made by the customer to the Modem/Fax Protection. This equipment may not be used on
coin service provided by the telephone company. Connection to party lines is subject to state tariffs. (Contact your state public utility commission or
corporation commission for information.)
Tripp Lite follows a policy of continuous improvement. Product specifications are subject to change without notice.
Made in China.
Warranty Registration
12
200903102 • 932470-EN
1111 W. 35th Street, Chicago, IL 60609 USA
773.869.1234 (USA) • 773.869.1212 (International)
www.tripplite.com
200903102 93-2470.indd 12 4/1/2009 3:56:30 PM
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8
  • Page 9 9
  • Page 10 10
  • Page 11 11
  • Page 12 12

Tripp Lite SU3000XLNAFTA Owner's manual

Category
Uninterruptible power supplies (UPSs)
Type
Owner's manual

Tripp Lite SU3000XLNAFTA is a SmartOnline UPS system designed to protect sensitive electronic equipment from power disturbances and outages. It provides reliable backup power, surge protection, and advanced power management features to keep your devices running smoothly. With its true on-line operation, the SU3000XLNAFTA continuously filters and regulates incoming AC power, ensuring a consistent and clean power supply to connected equipment. It also features an automatic self-test function to ensure reliable performance and early detection of potential problems.

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI