American Standard 7018801.002 Installation guide

American Standard
Brand
American Standard
Model
7018801.002
Category
Car kits
Type
Installation guide

This manual is also suitable for

- 1 -
Product names listed herein are trademarks of AS America, Inc.
© AS America, Inc. 2016
RECOMMENDED TOOLS
1
M965806 (3/17)
INSTALL SPOUT
Flat Head Screwdriver
Adjustable Wrench Tubing CutterSlip Jaw Pliers
Certied to comply with ANSI A112.18.1M
CAUTION
Turn off hot and cold water
supplies before begining.
12
13
SPOUT BASE
4
Fig. A.
Fig. B.
1
11 Blue Stripe (COLD)
11 Red Stripe
(HOT)
2
3
6
5
7
8
11a
11a
9
9A
10
5A
1A
Fig. B.
• Remove LOCKNUT (8) and WASHER (9) and (9a)
from SIDE VALVE SHANKS (10).
• Insert Hot and Cold SIDE VALVE HOSES (11),
FLEXIBLE SUPPLIES (11a) into mounting holes
making sure the SEAL WASHERS (12) are
properly seated in each HANDLE BASE (13).
• Assemble RUBBER WASHER (9), FRICTION
WASHER (9A) and thread LOCKNUT (8) onto
each SIDE VALVE SHANK (10) from underside
of sink or mounting surface.
• Align and center SIDE VALVES. Tighten
LOCKNUTS (8).
INSTALL VALVE BODIES
Fig. A.
• Insert SHANK (1) POP-UP ROD (2) and HOSE (3) through center hole,
making sure SEAL WASHER (4) is properly seated in spout base.
• Assemble RUBBER WASHER (5), FRICTION WASHER (5A) LOCKNUT
(6) and thread LOCKNUT (6) onto SHANK (1) from underside of sink or
mounting surface.
• Align and center SPOUT (7). Tighten LOCKNUT (6).
EDGEMERE
™
DUAL CONTROL WIDESPREAD
LAVATORY FAUCET
INSTALLATION
INSTRUCTIONS
7018.801
Thank you for selecting American Standard...
the benchmark of fine quality for over 100 years.
To ensure that your installation proceeds smoothly-please read
these instructions carefully before you begin.
- 2 -
2
M965806 (3/17)
• Apply a bead of putty to underside
of FLANGE (1).
INSTALL POP-UP DRAIN
2b
• Place SEAL (1) with small end facing up into TAILPIECE (2) and tighten
against DRAIN BODY (4). PIVOT ROD (3) opening in TAILPIECE (2) should
face the rear of the lavatory. Tighten LOCK NUT (5) with channel locks.
Do not over tighten.
1
2a
1
3
4
2
5
3
2
1
5
4
2c
• Assemble PIVOT ROD (1), PIVOT NUT (2), CLIP (3) and SEAL (4) as
shown. Hand tighten PIVOT NUT (2) Drop STOPPER (5) into drain.
(For vandal proof drain rotate stopper so PIVOT ROD (1) goes through
EYE (6) of STOPPER (5). Make connection to “P” TRAP.
• Remove one end of CLIP (3) from PIVOT ROD (1) by squeezing ends
together while sliding.
• Insert PIVOT ROD (1) into second or third hole in EXTENSION (7) and
reassemble CLIP (3). (EXTENSION (7) may need to be bent.)
• Adjust STOPPER (5) height by repositioning EXTENSION (7) and
tightening THUMBSCREW (8).
6
5
2
4
1
8
7
3
• Drop FLANGE (1) into LAVATORY
DRAIN (2). From below assemble
RUBBER GASKET (3), METAL
WASHER (4) and LOCK NUT (5).
Do not tighten.
- 3 -
4
• Operate LIFT KNOB (1) to verify that STOPPER (2) opens and
closes.
Note: If STOPPER (2) does not open and close properly then
refer to the “troubleshooting section” of these instructions.
CHECK OPERATION OF POP-UP
MAKE WATER SUPPLY AND WASTE CONNECTIONS
3
M965806 (3/17)
2
1
WASTE
OUTLET
HOT
COLD
1
3
3a
4
2
Blue Stripe
(C0LD)
Red Stripe (HOT)
• Connect FLEXIBLE SUPPLIES (1, 2) directly to wall supplies.
Connection on tting supplies are 3/8" compression.
Connect FLEXIBLE SUPPLY (1) (Marked with a Red Band) to the
Left wall supply and FLEXIBLE SUPPLY (2) (Marked with a Blue
Band) to Right wall supply.
• Connect the VALVE HOSES (3, 3a) to SPOUT TEE (4).
Use adjustable wrench to tighten connections.
Do not over tighten.
• Faucet supplies are 20" long from faucet base.
Note: If additional supply length is required, installer
must purchase additional parts separately.
Important: If SUPPLY HOSES (1, 2) are to
long, loop as illustrated to avoid kinking.
• Connect 1-1/4" O.D. tailpiece on POP-UP
DRAIN to waste outlet.
- 4 -
M965806 (3/17)
7
8
• With HANDLE (1) in OFF position, turn on WATER
SUPPLIES (2) and check all connections for leaks.
• Remove AERATOR (3).
• Operate HANDLE (1) to ush water lines thoroughly.
• Replace AERATOR (3).
SERVICE
CARE INSTRUCTIONS:
DO: SIMPLY RINSE THE PRODUCT CLEAN WITH CLEAR WATER. DRY WITH A SOFT COTTON FLANNEL CLOTH.
DO NOT: DO NOT CLEAN THE PRODUCT WITH SOAPS, ACID, POLISH, ABRASIVES, HARSH CLEANERS, OR A
CLOTH WITH A COARSE SURFACE.
TEST INSTALLED FITTING
5
5
HOT
1
1
COLD
2
2
“P” TRAP
4
WASTE
OUTLET
3
6
• Operate POP-UP KNOB (4) and ll lavatory with water.
Check that DRAIN STOPPER (5) makes a good seal
and retains water in Sink. If DRAIN STOPPER (5)
does not seal properly, please refer to Troubleshooting
section in these instructions.
• Release POP-UP KNOB (4) down and check all drain
connections and “P” trap for leaks. Tighten
if necessary.
CHECK DRAIN CONNECTIONS
Change Direction of the Handle
• Turn valves to OFF position.
• Turn off water supplies.
• Pull HANDLE (1) “UP” rmly to release from PLASTIC INSERT (6).
• Remove SCREW (3) and pull off PLASTIC INSERT (2).
• Remove RETAINING O-RING (4).
• Lift and turn STOP WASHER (5) 90˚. Replace RETAINING
O-RING (4).
• Re-install HANDLE ASSEMBLY.
To Change Cartridge:
• Remove HANDLE (1), ADAPTER (2) and SCREW (3) via
steps above.
• Loosen CARTRIDGE NUT (8) by turning counterclockwise then
pull up on cartridge to remove.
Aerator Clean Out
• AERATOR may accumulate dirt causing distorted and reduced
water ow. Remove AERATOR by using the AERATOR KEY
and rinse to clear any debris.
• If spout drips, operate handles several times from OFF to ON
position. Do not force - handles turn only 90˚.
90˚
90˚
2
3
1
4
5
8
7
5
6
M965806 (3/17)
- 5 -
M953475-YYYOA
Drain Assembly
M970009-YYY0A
Handle Kit
(Before August 2016)
M970130-YYY0A
Handle Kit
(After August 2016)
M964005-0070A
Valve
M970011-0070A
Mounting Kit
M970010-0070A
T-Connector
M970004-0070A
Aerator Kit
M970275-YYY0A
Lift Rod and Knob
M970276-YYY0A
Valve Kit
EDGEMERE
™
DUAL CONTROL WIDESPREAD
LAVATORY FAUCET
MODEL NUMBER
7018.801
HOT LINE FOR HELP
For toll-free information and answers to your questions, call:
1 (800) 442-1902
Mon. - Fri. 8:00 a.m. to 8:00 p.m. EST
Saturday 10:00 a.m. to 4:00 p.m. EST
IN CANADA 1-800-387-0369
(TORONTO 1-905-306-1093)
Weekdays 8:00 a.m. to 7:00 p.m. EST
IN MEXICO 01-800-839-1200
Replace the “YYY” with
appropriate finish code
CHROME 002
BRUSHED NICKEL 295
LEGACY BRONZE 278
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5

American Standard 7018801.002 Installation guide

American Standard
Brand
American Standard
Model
7018801.002
Category
Car kits
Type
Installation guide
This manual is also suitable for
Download PDF
report

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI

Related papers

Other documents