Poaeaon
Stream Media Mirror Dash Cam
User Manual
If you have any questions, please feel free to contact:
poaeaon.aftersales.service@gmail.com
To ensure that this product fully performs its functions during
use and has longer service life, please kindly carefully read this
manual before installation and use of this product.
Copyright warning
If without authorization, recording information under copyright
protection might infringe the copyrighter's rights and interests,
and violate Copyright Law.
Notes
1. If abnormal conditions appear, such as crack of the charger's
housing and crack of the product's housing, please immediately
discontinue use of the product and contact our support staff.
2. Do not operate the product while driving, to avoid possible
accidents due to distracted attention.
3. If the product needs cleaning, please use soft cloth and gently
scrub the product. Do not use any chemical agents to clean the
product.
4. Do not expose the product to heat or direct sunlight for a
long time, especially such heat environment in the vehicle.
5. Do not store or use the product in a humid environment, or in
an environment with inflammable, explosive or corrosive gas or
liquid.
6. Do not remove or insert the TF card when the product is
recording.
Warning
Unless you are a professional, do not perform disassembly,
assembly, modification or repair of the product by yourself, which
might damage the product, and even cause more serious
consequences, such as fire disaster.
This manual is attempting to provide accurate information. We
are not responsible for any consequence arising from any
misprints or translation errors. This manual's copyright belongs to
us. Any unauthorized copying or translation of the whole or part of
this manual for commercial purposes is not allowed. We reserve
the right to interpret contents in this manual.
Notes
In case of upgraded software, parameters might change without
prior notice, which is subject to actual product parameters.
Appearance and description of button functions
Illustration of buttons
1. USB power interface 2. Rear camera interface 3. TF card slot
4. Reserved hole 5. Power 6. Reset
Functions of buttons and interfaces
1. Power button
Function 1: power on/off
When the DVR is turned off, press the "power" button to turn
on the DVR and the DVR automatically starts working. When the
DVR is turned on, press and hold the "power" button for 3 seconds,
and then the video and user's settings will be automatically saved
and the DVR will be turned off.
Function 2: screen saver or screen on/off
After the DVR is turned on, press the "power" button under any
mode to turn on screen saver. Press the "power" button again to
turn off the screen. And press the "power" button again or touch
the screen to turn on the screen. (This function does not influence
video recording.)
2. Reset button
If the DVR's system is halted, press the "reset" button to turn off
the DVR.
3. USB power interface
Connect DC 5V (USB 5V/2.5A) power supply to provide power to
the DVR. Connect the DVR to the car charger. Then when the car
engine is turned on, the DVR will start recording automatically
(which requires relevant settings in the DVR's setting menu); when
the car engine is turned off, the DVR will stop recording
automatically and save recorded files. Warm reminder: Please use
the original car charger to provide power to the DVR. Otherwise,
the DVR might be damaged.
4. Rear camera interface
Connect AV-IN interface on the rear camera.
5. TF card slot
Insert a TF card and the video files will be saved in the TF card.
Use of the TF card: Please check if the TF card is inserted in a
correct direction. If the inserting direction is incorrect, the DVR and
the TF card might be damaged; please use a high speed SDHC TF
card. A high speed TF card has a mark of C10. Please use a genuine
TF card with a mark of C10 or above for this DVR. When a TF card
is inserted into this DVR, please format the card in the DVR's
menu.
Operation guide
1. Installation of the car DVR
1) Turn off the vehicle engine.
2) Insert a TF card into the card slot on the DVR.
[Attention] Please use a high speed TF card (Class 10) with
capacity of 8GB at least. 64GB is supported at most; however, 32GB
is recommended, because most of 64GB TF cards are not
compatible very well with this product, and halted system, blank
screen and failure to start the product might occur if 64GB card is
used.
3) Use the rubber buckle on the back to fix the DVR on the
original rear view mirror in the vehicle.
4) Plug the vehicle charger into the vehicle's cigarette lighter, and
plug the charger's USB port into the DVR's USB power interface.
5) Install the rear camera on the back of the vehicle. Pay
attention to the direction during installation. Wires could be laid
along the vehicle ceiling. When installation is completed, connect
the rear plug to the rear camera's interface on the DVR.
[Attention] If the reversing camera is needed, it is necessary to
connect the red wire for the rear camera to the positive pole of the
reversing light. Please contact a 4S shop or a professional
maintenance shop to complete the installation.
6) Adjust the position of the camera to make sure that the
camera is parallel to the ground.
7) Start the vehicle engine to check if the DVR is correctly
installed.
[Attention] If the TF card is first used for the DVR, please
format the TF card in the DVR's menu.
2. Brief introduction to functions
Introduction to the main screen
1) Icon for start/stop video recording: start ; stop
2) One button to capture pictures: on ; off
3) One button to mute: audio on ; audio off
4) One button to lock: unlock icon ; lock icon
5) Video playback
6) System setting
7) Time/date/day of week
8) Video status indicator
9) When the DVR is not recording video, it displays the time
left for normal video that the TF card can save; when the DVR
is recording, it displays how long the current video has been
recorded.
10) Indicator for GPS connection status
11) Icon for screen brightness adjustment
12) Status bar: As with the status bar on the mobile phone, the
displayed icon depends on which function is turned on.
① Click "settings"
to enter the setting screen and set
the movie mode and system. Please note that the DVR must
stop recording video before entering the setting screen.
1) Movie mode:
In this setting screen, users can choose 1296P (SHD 30fps) or
1080P (FHD 30fps) video resolution. This setting is only applicable
to the front camera. The rear camera only records 1080P video.
2) Movie clip time
Users can choose movie clip time as 1 minute, 3 minutes or 5
minutes.
3) Night mode (dynamic frame rate reduction)
In this setting screen, users can turn on/off the video's frame rate
adjustment at night according to light illumination, making the
brightness of video and screen display achieve the starlight effect.
4) Exposure adjustment
In this setting screen, users can increase or decrease the front
camera's exposure intensity.
5) Smart LCD brightness adjustment
LCD brightness could be adjusted manually or automatically.
Users can manually adjust LCD brightness as they like. Or, LCD
brightness is adjusted automatically for the day and the night, with
19:00 as the switch time.
6) G-sensor (collision induction)
This DVR is equipped with built-in G-sensor. If serious vehicle
collision occurs, the current video will be locked, and the unlock
icon at the bottom of the screen will be changed to the lock
icon ; the locked video will be saved as a special file and won't
be overwritten by loop videos.
[Reminder]
a. The locked file's name begins with Lock, the normal file's name
begins with Video, and the motion-detection-induced file’s name
begins with Event.
b. The sensitivity of G-sensor could be adjusted. Please change
the G-sensor setting in "settings" based on actual need.
[Attention] When G-sensor is on, the files might be locked due
to road bumps while driving. If too many files are locked, available
memory of the TF card will be reduced. Please format the TF card
on a regular basis (around every two or three weeks) through this
DVR’s formatting function to ensure the DVR works properly.
7) Parking monitoring
Open the park mode in the menu. If vibration occurs after the
DVR is turned off, the DVR could detect vibration through G-
sensor and is automatically turned on to record video for 30
seconds, and then the DVR is turned off. (This file will be locked.
The locked file will be saved as a special file and won't be
overwritten by loop videos.) If the park mode is off, then the DVR
won't be turned on when vibration occurs.
8) Screen saver
If no operation on the DVR, the countdown to turning off
backlight could be set as off, 1 minute or 3 minutes. After the
screen saver starts, click the screen and the screen backlight will be
on automatically. If the countdown is off and no operation on the
DVR, the screen backlight will be always on.
9) Language options
In this setting screen, users could choose a language as needed;
this DVR supports Simplified Chinese, English, Traditional Chinese
and Japanese.
10) Volume
Users can set the audio played when turning on/off the DVR and
also set the key tone. Four options of off, high, middle and low are
available.
11）Frequency
According to the light source frequency, set the corresponding
flashing frequency
12) Date/clock
In this setting screen, users can set the date and the time.
Touch the icon to adjust the date and the
time. After setting one item, press OK button to confirm and
switch to the next item until exit setting.
[Attention] Please set the correct date and time before use
the DVR, in order to effectively record the correct date and
time if the accident occurs.
13) Time zone select
14) Format SD Card
Users can format the current SD card. Click "YES" to format the
card. Attention: If the TF card is first used for the DVR, please
format the TF card. After the card is formatted, all contents in the
card are deleted and unrecoverable. Please carefully choose to
format it.
15) System reset
After users click this function, all menu options are reset to the
default settings and the clock does not need resetting.
16) Firmware version
The firmware version information includes the software
information, time and other information. Users could not set them.
② Click "playback"
to enter the playback screen and
view videos in the TF card.
1) Click the lock icon at the bottom right corner to lock the
current video. Click the icon again to unlock the current video and
the icon is displayed.
2) Click the deletion icon to delete the current video or
image, except the locked files.
The normal video file recorded by the front camera
The normal video file recorded by the rear camera
The locked video file recorded by the front camera
The locked video file recorded by the rear camera
Captured pictures
3) page-left; page right. Page-left and page-right buttons
are for switching videos or captured pictures to view. Click the icon
to play the current video. Click the icon to pause the
current video. is for fast backward and is for fast forward.
Reversing camera
After the vehicle is put into reverse, the DVR's screen is switched
to the rear camera screen and displays auxiliary lines for reverse.
After vehicle reversing is completed, the DVR's screen
automatically returns to the normal screen.
[Attention] If the reversing camera is needed, it is necessary to
connect the red wire for the rear camera to the positive pole of the
reversing light. Please contact professional vehicle maintenance
staff to complete the installation.
Product specifications
Features
HD camera, HD video
Effective camera pixels
12M
Aperture
2.5
Camera angle
170 degree A+ grade high
resolution ultra-wide angle lens
Video resolution
1296P \ 1080P
Video compression
format
MJPEG
Video format
MOV
Image format
JPG
Frame rate
30FPS
Storage temperature
-10℃~70℃
Operating temperature
-5℃~60℃
Operating humidity
15-65% RH
Storage capacity
8GB~64GB TF card
Operating voltage
DC 5V
Operating current
2.0A
Power interface
MINI USB DC5V -2.5A
*Note: We reserve the right to modify this product; the design
and specifications are subject to change without prior notice.
Packing list
HD Car DVR
Items included
Unit
Quantity
Car DVR
pc
1
Vehicle charger
pc
1
Rear camera
pc
1
Connecting
wire for camera
pc
1
User Manual
pc
1
Binding band
pc
4 ( 2 for replacement)
Reminder: When you purchase this product, if you find any
item in the package is inconsistent with items in above packing
list, please contact your dealer timely.
Troubleshooting
1. The DVR displays that the memory is full, and the loop videos
could not be recorded.
1) If a new TF card is first used for the DVR, it will be reminded
that the TF card should be formatted first. Then please format the
TF card first. If without reminding, please also format the TF card
first before use the DVR.
2) Check video duration and loop video settings. The options
include 1 minute / 3 minutes / 5 minutes / off. If it is set as off, then
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
/
