MicroNet SP362C/SP363C-10/SP363C-20 User manual

MicroNet
Brand
MicroNet
Model
SP362C/SP363C-10/SP363C-20
Category
Network media converters
Type
User manual
Specifications
Standard
IEEE802.3ab
1000BASE-T;
IEEE802.3z
1000BASE-SX
Interface
TP Connections
SP362C
Fiber
Connections
RJ-45 port x 1 (1000 Mbps)
SC connector Fiber port x 1 (1000 Mbps)
62.5/125ìm
or 50/125ìm
Model
SP363C-10/20
1000BASE-T: UTP Category 5, up to 100m
IEEE802.3ab
1000BASE-T;
IEEE802.3z
1000BASE-LX
9 or 10/125ìm,
Fiber Mode
Multi-mode fiber Single-mode fiber
Wave Length
850nm 1310nm
MAX. Distance
220/550m 10/ 20Km
Data
Transfer Rate
2000Mbps/full-duplex
Operating
Temperature
0º ~ 40º C (32ºF ~ 104ºF)
Operating
Humidity
5%~90%
Dimension
94 x 70.3 x 94 mm (D x W x H)
Weight (g)
220 g
Power Supply
+5VDC, 2A
External power supply
Emission
FCC Class A, CE
P/N: 2300-0429
6
7
Gigabit Media Converter
Model No.: SP362C/SP363C Series
http://www.micronet.info
Quick Installation Guide
The “Fiber Mode” must be set to “FORCE” when you intend to
connect a pair of SP362C/SP363C series via fiber optic cable at
both ends of a fiber connection. It does not work if “Fiber Mode” is
set to “AUTO” in this connection.
Warning:
For other/different model converter fiber connection, both local and
remote fiber mode must be set to an identical mode (“AUTO or
FORCE”) according to their operation/configuration. Refer to the
corresponding device/converter's Technical Manual for proper
setting.
Remote Side: Force
Fiber Mode
AUTO FORCE
Fiber Optic
Fiber Mode
AUTO FORCE
Local Side: Force
SP362C/363C series SP362C/363C series
5
SP362C/SP363C-10/20 Fiber
FORCE
SP362C/SP363C-10/20 Fiber
FORCE
SP362C/SP363C-10/20 Fiber
AUTO
SP362C/SP363C-10/20 Fiber
AUTO
Other/different Media converter
AUTO / 1000Mbps
Other/different Fiber NIC
AUTO / 1000Mbps
TO
TO
TO
This is a Class A product. In a domestic environment, this product
may cause radio interference, in which case the user may be
required to take adequate measures.
CE Mark Warning
2
SP362C/SP363C series Gigabit Media converter is primarily
designed for larger and higher bandwidth demanding workgroups
that require expansion of the Ethernet network.
SP362C/SP363C series is designed with IEEE802.3z/ab and
support two type of media for network connection such as
1000BASE-T and 1000BASE-SX/LX. The converter can be use as
a standalone unit or as a side-in module to the 19” converter rack
(up to 12 units) for use at a central wiring closet. At full duplex mode,
the converter can extend distances up to 55o meters for multi-mode
fiber and up to 20 kilometers for single-mode fiber.
Product Overview
Package Contents
Thank you for purchasing Micronet Ethernet Media Converter.
Before you start installing the Media Converter, verify the
following items in the package
• Gigabit Media Converter
• Quick Installation Guide
• Power Adapter
1
This converter provides one TP port and one FX port. For the FX
port, it provides options of either multi-mode (SP362C) or single-
mode (SP363C-10/20) fiber accommodating SC connector. For the
TP port, it uses RJ-45 connector and supports Auto-Uplink.
3 4
• The relative humidity should be less than 90 percent, non
condensing.
• Surrounding electrical devices should not exceed the
electromagnetic field (RFC) standards for IEC 801 3, Level 2
(3V/M) field strength.
• Make sure that the equipment receives adequate ventilation. Do
not block the ventilation holes on each side of the switch or the fan
exhaust port on the side or rear of the equipment.
For as a standalone unit:
• Verify the power adapter conforms to your country DC power
requirement and insert the power plug.
For as a slide-in unit:
• Verify the media converter is the right model and conforms to the
chassis slot. The media converter and Rack are built to match in
dimensions, DC jack, DC receptacle and power safety
• Locate +5VDC power jack on converter back, carefully slide in and
plug to 19” rack +5VDC power receptacle.
•
•
•
•
•
•
•
•
•
Installation
As with any electric device, you should place the equipment where
it will not be subjected to extreme temperatures, humidity, or
electromagnetic interference. Specifically, the site you select should
meet the following requirements:
• The ambient temperature should be between 0 to 40 degrees
Celsius.
•
Physical Description
Cable connection
Connect with fiber cable, the Tx, Rx fiber cable
must be paired at both ends.
Default: AUTO. The “Fiber Mode” must be set to
“FORCE” when you intend to connect a pair of
SP362C/SP363C series via fiber optic cable at
both ends of a fiber connection.
Fiber port
TP port
Connect with TP Cat. 5 cable to TP port
The 1000 TP port is transmit/receive wires
auto-link. It will auto cross-connect transmit/
receive wires to a switch or to a workstation.
SP362C
Port type Cable Type
1000BASE-T
Cat. 5, UTP, RJ-45
Max. Length
100 meters
1000BASE-SX
Multi-mode Fiber of 850nm
(62.5/125µm)
220 meters
1000BASE-SX
Multi-mode Fiber of 850nm
(50/125µm)
550 meters
SP363C-10/20
Port type Cable Type
1000BASE-T
Cat. 5, UTP, RJ-45
Max. Length
100 meters
1000BASE-LX
Single-mode Fiber of 1310nm
(9 or 10/125µm)
10 Km
(SP363C-10)
20 Km
(SP363C-20)
Gigabit Media converter Front view
Gigabit Media converter Rear view
5VDC
FIBER MODE
AUTO FORCE
TX RX
FX
ACT
PWR
TP
LINK
FDX
LED Indication
LED Status
PWR
Green
Indication
The Power is on
FX LINK
Green A valid network connection established
on Fiber port
FX FDX
Green Connection in full duplex mode
TP FDX
Green Connection in full duplex mode
ACT
Green Transmitting/Receiving data
TP LINK
Green A valid network connection established
on TX port
  • Page 1 1
  • Page 2 2

MicroNet SP362C/SP363C-10/SP363C-20 User manual

MicroNet
Brand
MicroNet
Model
SP362C/SP363C-10/SP363C-20
Category
Network media converters
Type
User manual
Download PDF
report

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI

Related papers

Other documents