JVC LYT1300-001A User manual

Brand: JVC

Model: LYT1300-001A

Category: Cassette players

Type: User manual

LYT1300-001A

Master Page: Cover1

ENGLISH

CU-VH1

GETTING STARTED 9

VIDEO PLAYBACK

DIGITAL STILL CAMERA

(D.S.C.) PLAYBACK

ADVANCED FEATURES

REFERENCES

TERMS

Please visit our Homepage on the World Wide

Web for Digital Video Camera:

For Accessories:

http://www.jvc.co.jp/english/cyber/

http://www.jvc.co.jp/english/accessory/

INSTRUCTIONS

DIGITAL HD PLAYER

CU-VH1E.book Page 1 Friday, March 26, 2004 1:55 PM

2 EN

Master Page: Left-Safety-Dummy

Using This Instruction Manual

● All major sections are listed in the Table Of Contents on the cover page.

● Notes appear after most subsections. Be sure to read these as well.

● Basic and advanced features/operation are separated for easier reference.

It is recommended that you…

… refer to the Index (墌 pg. 56 – 58) and familiarise yourself with button locations, etc. before use.

… read thoroughly the Safety Precautions and Safety Instructions that follow. They contain extremely

important information regarding the safe use of this product.

SAFETY PRECAUTIONS

Dear Customer,

Thank you for purchasing this digital HD player. Before use, please read the safety information and

precautions contained in the following pages to ensure safe use of this product.

You are recommended to carefully read the cautions on pages 50 through 52 before use.

IMPORTANT (for owners in the U.K.)

Connection to the mains supply in the United

Kingdom.

DO NOT cut off the mains plug from this

equipment.

If the plug fitted is not suitable for the power

points in your home or the cable is too short to

reach a power point, then obtain an appropriate

safety approved extension lead or consult your

dealer.

BE SURE to replace the fuse only with an

identical approved type, as originally fitted, and

to replace the fuse cover.

If nonetheless the mains plug is cut off be sure to

remove the fuse and dispose of the plug

immediately, to avoid possible shock hazard by

inadvertent connection to the mains supply.

If this product is not supplied fitted with a mains

plug then follow the instructions given below:

DO NOT make any connection to the Larger

Terminal coded E or Green.

The wires in the mains lead are coloured in

accordance with the following code:

If these colours do not correspond with the

terminal identifications of your plug, connect as

follows:

Blue wire to terminal coded N (Neutral) or

coloured black.

Brown wire to terminal coded L (Live) or coloured

Red.

If in doubt — consult a competent electrician.

Blue to N (Neutral) or

Black

Brown to L (Live) or Red

WARNING:

TO PREVENT FIRE OR SHOCK

HAZARD, DO NOT EXPOSE THIS

UNIT TO RAIN OR MOISTURE.

CAUTIONS:

● To prevent shock, do not open the cabinet. No

user serviceable parts inside. Refer servicing to

qualified personnel.

● When you are not using the AC Power Adapter/

Charger for a long period of time, it is

recommended that you disconnect the power

cord from AC outlet.

NOTES:

● The rating plate (serial number plate) and safety

caution are on the bottom and/or the back of

the main unit.

● The rating plate (serial number plate) of the AC

Power Adapter/Charger is on its bottom.

CAUTIONS:

● This player is designed to be used with NTSC-

type colour television signals. It cannot be used

for playback with a television of a different

standard. However, LCD monitor playback is

possible anywhere.

● Use the JVC BN-V416U/V428U battery packs

and, to recharge them or supply power to the

player from an AC outlet, use the provided

multi-voltage AC Power Adapter/Charger. (An

appropriate conversion adapter may be

necessary to accommodate different designs of

AC outlets in different countries.)

CU-VH1E.book Page 2 Friday, March 26, 2004 1:55 PM

EN 3

Master Page: Right-Safety

SOME DO’S AND DON’TS ON THE SAFE USE OF EQUIPMENT

This equipment has been designed and manufactured to meet international safety standards but, like any

electrical equipment, care must be taken if you are to obtain the best results and safety is to be assured.

DO read the operating instructions before you attempt to use the equipment.

DO ensure that all electrical connections (including the mains plug, extension leads and interconnections

between pieces of equipment) are properly made and in accordance with the manufacturer’s

instructions. Switch off and withdraw the mains plug when making or changing connections.

DO consult your dealer if you are ever in doubt about the installation, operation or safety of your equipment.

DO be careful with glass panels or doors on equipment.

DON’T continue to operate the equipment if you are in any doubt about it working normally, or if it is

damaged in any way — switch off, withdraw the mains plug and consult your dealer.

DON’T remove any fixed cover as this may expose dangerous voltages.

DON’T leave equipment switched on when it is unattended unless it is specifically stated that it is designed

for unattended operation or has a standby mode. Switch off using the switch on the equipment and

make sure that your family knows how to do this. Special arrangements may need to be made for

infirm or handicapped people.

DON’T use equipment such as personal stereos or radios so that you are distracted from the requirements of

road safety. It is illegal to watch television whilst driving.

DON’T listen to headphones at high volume, as such use can permanently damage your hearing.

DON’T obstruct the ventilation of the equipment, for example with curtains or soft furnishings. Overheating

will cause damage and shorten the life of the equipment.

DON’T use makeshift stands and NEVER fix legs with wood screws — to ensure complete safety always fit

the manufacturer’s approved stand or legs with the fixings provided according to the instructions.

DON’T allow electrical equipment to be exposed to rain or moisture.

ABOVE ALL

— NEVER let anyone especially children push anything into holes, slots or any other opening in the case —

this could result in a fatal electrical shock;

— NEVER guess or take chances with electrical equipment of any kind — it is better to be safe than sorry!

When the equipment is installed in a cabinet or on a shelf, make sure that it has sufficient space on all sides

to allow for ventilation (10 cm or more on both sides, on top and at the rear).

Do not block the ventilation holes.

(If the ventilation holes are blocked by a newspaper, or cloth etc. the heat may not be able to get out.)

No naked flame sources, such as lighted candles, should be placed on the apparatus.

When discarding batteries, environmental problems must be considered and the local rules or laws

governing the disposal of these batteries must be followed strictly.

The apparatus shall not be exposed to dripping or splashing.

Do not use this equipment in a bathroom or places with water.

Also do not place any containers filled with water or liquids (such as cosmetics or medicines, flower vases,

potted plants, cups etc.) on top of this unit.

(If water or liquid is allowed to enter this equipment, fire or electric shock may be caused.)

CAUTION!

The following notes concern possible physical damage to the player and to the user.

When carrying, be sure to always securely attach and use the provided strap. Carrying or holding the player

by the LCD monitor can result in dropping the unit, or in a malfunction.

Take care not to get your finger caught in the cassette holder cover. Do not let children operate the player,

as they are particularly susceptible to this type of injury.

CAUTION!

Connecting cables (S, audio/video, USB, etc.) to the player and leaving it on top of the TV is not

recommended, as tripping on the cables will cause the player to fall, resulting in damage.

CU-VH1E.book Page 3 Friday, March 26, 2004 1:55 PM

4 EN

Master Page: Left-Safety

In order to keep the best performance and furthermore for electromagnetic compatibility, we recommend to

use cables exceeding the following length.

The inrush current of this apparatus is 2 amperes.

CAUTION!

Where there are strong electromagnetic waves or magnetism, for example near a radio or TV transmitter,

transformer, motor, etc., the picture may be disturbed. In such case, please keep the product away from the

sources of the disturbance.

䡲 This player is designed exclusively for the digital video cassette, SD Memory Card and MultiMediaCard.

Only cassettes marked “ ” and memory cards marked “ ” or “ ” can be used

with this unit.

Before using the player…

… make sure you only use cassettes with the Mini DV mark .

… make sure you only use memory cards with the mark or .

… remember that this player is not compatible with other digital video formats.

… remember that this player is intended for private consumer use only. Any commercial use without proper

permission is prohibited. (Even if you record an event such as a show, performance or exhibition for

personal enjoyment, it is strongly recommended that you obtain permission beforehand.)

This equipment is in conformity with the provisions and protection requirements of the corresponding

European Directives. This equipment is designed for professional video appliances and can be used in the

following environments:

● residential area

● commercial and light industry; e.g. offices or theatres

● urban outdoors

On the AC adapter AA-V40EG, AA-V40EK

Port Cable Length

Core filter/winding the cable around the filter

AC input

Dedicated AC power cord in the package

1.8 m No filter

DC output Dedicated DC cord in the package 2.0 m AC adapter side: No filter

Player side: ZCAT 1730-0730/once

On the main unit CU-VH1

Port Cable Length

Core filter/winding the cable around the filter

DC input Dedicated DC cord and the AC adapter

AA-V40EG or AA-V40EK in the

package

2.0 m AC adapter side: No filter

Player side: ZCAT 1730-0730/once

S-Videp output Dedicated S-Video cable in the

package

1.0 m No filter

AV output Dedicated AV cable in the package 1.0 m No filter

Y/Pb/Pr output Dedicated Component video cable in

the package

2.0 m No filter

USB Dedicated USB cable in the package 1.5 m Player side: ZCAT 2035-0930/once

i-Link/

DV input-output

Dedicated DV cable for JVC Video

Camera, part number VC-VDV204U or

VC-VDV206U, optional accessories.

2.0 m Player side: ZCAT 2436-1330/twice

Another side: ZCAT 2035-0930/once

Headphone Shielded cable 3.0 m No filter

Microphone Dedicated Audio (extension) cable in

the package

0.2 m ZCAT 1730-0730/once

CU-VH1E_02Safety.fm Page 4 Friday, March 26, 2004 5:01 PM

EN 5

Master Page: Right

NOTES:

● In order to maintain optimum performance of the player, provided cables may be equipped with one or

more core filter. If a cable has only one core filter, the end that is closest to the filter should be connected to

the player.

● Make sure to use the provided cables for connections. Do not use any other cables.

Provided Accessories

AC Power Adapter/

Charger

AA-V40EG

AA-V40EK

DC Cord Battery Pack

BN-V416U

Audio/Video Cable

(RCA plug to RCA plug)

S-Video Cable Component Video Cable USB Cable Audio Cable

(for connection of

external microphone

墌 pg. 7)

Shoulder Strap

(墌 pg. 7 for attachment)

RCA-BNC Adapter x 3 Remote Control Unit

RM-V718U

Lithium Battery CR2025*

(for remote control unit)

* A lithium battery is pre-

installed in the Remote

Control Unit at time of

shipment (with

insulation sheet). To use

the Remote Control

Unit, remove the

insulation sheet.

Core Filter

(墌 pg. 6 for attachment)

•Large x 1

•Medium x 1

•Small x 2

Connector Cover

CU-VH1E.book Page 5 Friday, March 26, 2004 1:55 PM

6 EN

Master Page: Left

How To Attach The Core Filter

Attach the core filters to the cables. The core filter

reduces interference.

Types of core filters

* Optional

(If you have an optional JVC i.LINK cable

VC-VDV206U or VC-VDV204U with core

filters, it is not necessary to attach the provided

core filter. If you are going to use any other

i.LINK cable, attach the provided core filter.)

The procedure below is an example of winding

cable once.

1 Release the stoppers on both ends of the core

filter.

2 Run the cable through the core filter, leaving

approx. 3 cm of cable between the cable plug

and the core filter. Wind the cable once around

the outside of the core filter as shown in the

illustration.

● Wind the cable so that it is not slack.

3 Close the core filter until it clicks shut.

NOTES:

● Take care not to damage the cable.

● When connecting a cable, attach the end with the

core filter to the player.

Size Cable

Times to

wind

Large i.LINK cable* Twice

Medium USB cable Once

Small

DC cord

Audio cable

Once

Stopper

3 cm

Wind once.

CU-VH1E.book Page 6 Friday, March 26, 2004 1:55 PM

EN 7

Master Page: Right

How To Attach The Strap

1 Thread the strap through the eyelet a.

2 Fold it back and thread it through the strap guide

and the buckle.

● To adjust the length of the strap, loosen and

then tighten the strap in the buckle.

3 Repeat the procedure to attach the other end of

the strap to the other eyelet b.

4 Confirm the strap is not twisted.

How To Attach The Connector

Cover

To protect the connectors, attach the provided

connector cover to the rear panel of the player when

the player is not in use.

How To Use The Audio Cable

When using an optional external microphone,

connect to the provided audio cable (with a core

filter attached), then connect the audio cable to the

player. The core filter reduces interference.

Eyelet b

Eyelet a

Buckle

Strap guide

Microphone

Audio cable

(provided)

Core filter

Open the connector cover.

To MIC

CU-VH1E.book Page 7 Friday, March 26, 2004 1:55 PM

8 EN

Master Page: Left

GETTING STARTED 9

Power .........................................................................9

Operation Mode .......................................................11

LCD Monitor ............................................................12

Brightness Adjustment Of The Display ......................12

Date/Time Settings ....................................................13

Loading A Cassette

/Unloading A Cassette ..........................................14

Loading A Memory Card

/Unloading A Memory Card .................................15

VIDEO PLAYBACK 16

VIDEO PLAYBACK ......................................................16

Normal Playback ......................................................16

Still Playback ............................................................16

Frame-By-Frame Playback ........................................16

Shuttle Search ...........................................................17

Blank Search ............................................................17

Connections To A TV Or VCR ..................................18

DIGITAL STILL CAMERA (D.S.C.) PLAYBACK 20

D.S.C. PLAYBACK .......................................................20

Normal Playback Of Images .....................................20

Auto Playback Of Images .........................................20

Index Playback Of Files ............................................21

Viewing File Information ..........................................21

Removing On-Screen Display ...................................21

Protecting Files .........................................................22

Deleting Files ...........................................................23

Resetting The File Name ...........................................24

Setting Print Information (DPOF Setting) ...................24

Initialising A Memory Card .......................................25

ADVANCED FEATURES 26

MENUS FOR DETAILED ADJUSTMENT .......................... 26

Changing The Menu Settings .................................... 26

PLAYBACK MENUS ..................................................... 27

NAVIGATION............................................................. 30

NAVIGATION Function ........................................... 30

DUBBING ................................................................. 32

Dubbing To Or From A VCR .................................... 32

Dubbing To Or From A Video Unit Equipped With

An i.LINK Connector (Digital Dubbing) ................ 33

Recording From The Middle Of A Tape .................... 34

Dubbing Still Images Recorded On A Tape To

A Memory Card .................................................... 36

USING THE REMOTE CONTROL UNIT ...........................37

Audio Dubbing (DV mode only) ............................... 40

SYSTEM CONNECTIONS .............................................. 41

Connection To A Personal Computer ....................... 41

REFERENCES 42

DETAILS ....................................................................42

TROUBLESHOOTING ...................................................43

CAUTIONS ................................................................. 50

USER MAINTENANCE ..................................................53

SPECIFICATIONS ........................................................ 54

INDEX .......................................................................56

TERMS 59

CONTENTS

CU-VH1E.book Page 8 Friday, March 26, 2004 1:55 PM

EN 9

Master Page: Right-start

GETTING STARTED

This player’s 2-way power supply system lets you

choose the most appropriate source of power. Do

not use provided power supply units with other

equipment.

Charging The Battery Pack

Make sure you unplug the player’s DC cord from

the AC Power Adapter/Charger.

2 Plug the AC Power Adapter/Charger’s power cord

into an AC outlet. The POWER indicator lights.

3 Attach the battery pack with the YZ mark

aligned with the corresponding marks on the AC

Power Adapter/Charger. The CHARGE indicator

begins blinking to indicate charging has started.

4 When the CHARGE indicator stops blinking but

stays lit, charging is finished. Remove the battery

pack.

5 Unplug the AC Power Adapter/Charger’s power

cord from the AC outlet.

*Provided

NOTES:

● If the protective cap is attached to the battery

pack, remove it first.

● If you connect the player’s DC cord to the AC

Power Adapter/Charger during battery charging,

power is supplied to the player and charging stops.

● Charging is not possible if the wrong type of

battery is used.

● When charging the battery pack for the first time

or after a long storage period, the CHARGE

indicator may not light. In this case, remove the

battery pack from the AC Power Adapter/Charger,

then try charging again.

● If the battery operation time remains extremely

short even after having been fully charged, the

battery is worn out and needs to be replaced.

Please purchase a new one.

● For other notes, 墌 pg. 42.

Using The Battery Pack

With the arrow on the battery pack pointing to

the left, push the battery pack slightly against the

battery pack mount a.

2 Slide the battery pack to the left until it locks in

place b.

To detach the battery pack...

Slide the battery pack to the right slightly while

sliding BATT. RELEASE to detach it.

NOTES:

● Available time is reduced significantly under the

following conditions:

• The LCD monitor is used repeatedly.

• The playback mode is engaged repeatedly.

● Before extended use, it is recommended that you

prepare enough battery packs to cover 3 times the

planned recording time.

Power

Battery pack Charging time

BN-V416U* Approx. 2 hr.

BN-V428U Approx. 3 hr. 20 min.

Battery pack

BN-V416U or

BN-V428U

To AC outlet

POWER indicator

CHARGE indicator

DC OUT connector

AC Power Adapter/

Charger

TTENTION:

Before detaching the power source, make sure

that the player’s power is turned off. Failure to do

so can result in a player malfunction.

BATT.RELEASE

Switch

Arrow

CONTINUED ON NEXT PAGE

CU-VH1E.book Page 9 Friday, March 26, 2004 1:55 PM

10 EN

Master Page: Left

Using AC Power

Make sure you unplug the player’s DC cord from

the AC Power Adapter/Charger.

2 Connect the AC Power Adapter/Charger to the

player as shown in the illustration above.

NOTES:

● The provided AC Power Adapter/Charger features

automatic voltage selection in the AC range from

110 V to 240 V.

● For other notes, 墌 pg. 42.

About Batteries

Lithium-ion is vulnerable in colder temperatures.

DANGER! Do not attempt to take the batteries apart,

or expose them to flame or excessive heat, as it may

cause a fire or explosion.

WARNING! Do not allow the battery or its terminals

to come in contact with metals, as this can result in

a short circuit and possibly start a fire.

The Benefits Of Lithium-Ion Batteries

Lithium-ion battery packs are small but have a large

power capacity. However, when one is exposed to

cold temperatures (below 10°C), its usage time

becomes shorter and it may cease to function. If this

happens, place the battery pack in your pocket or

other warm, protected place for a short time, then

re-attach it to the player. As long as the battery pack

itself is not cold, it should not affect performance.

(If you’re using a heating pad, make sure the battery

pack does not come in direct contact with it.)

For other notes, 墌 pg. 42.

Open the cover.

AC Power Adapter/

Charger

To DC connector

To AC outlet

Power cord

DC cord

To DC OUT

connector

Mark

CU-VH1E.book Page 10 Friday, March 26, 2004 1:55 PM

EN 11

Master Page: Right

To turn on the player, set the Power Switch to “ON”

while pressing down the Lock Button located on the

switch.

Choose the appropriate operation mode according

to your preference using Playback Mode Switch for

playback and Video Output Mode Switch for signal

output.

Operation Mode

Power Switch Position

ON:

Allows you to switch on the player.

OFF:

Allows you to switch off the player.

Power Switch

Video Output Mode

Switch

Lock Button

Playback Mode Switch

Playback Mode Switch Position

VIDEO:

Allows you to play back a tape.

MEMORY:

Allows you to play back images stored in a

memory card or access data stored in a memory

card.

Video Output Mode Switch Position

COMPONENT VIDEO OUT:

Allows you to output signals from the Component

Video connector. When you view images on the

connected TV, set the switch to this mode.

(墌 pg. 18)

LCD MONITOR:

When you view images on the player’s LCD

monitor or TV connected via video or S-video

cable, set the switch to this mode.

GETTING STARTED

CU-VH1E.book Page 11 Friday, March 26, 2004 1:55 PM

12 EN

Master Page: Left

Press the Monitor Opening Button and open the

LCD monitor fully.

To view images on the LCD monitor, set the Video

Output Mode Switch to “LCD MONITOR”.

(墌 pg. 11)

NOTES:

● The image on the LCD monitor and the image on

the TV screen may look differently in terms of the

brightness and colour. Confirm the final image on

the TV screen.

● Coloured bright spots may appear all over the LCD

monitor. However, this is not a malfunction.

(墌 pg. 45)

1 Set the Power Switch to “ON” while pressing

down the Lock Button located on the switch.

2 Open the LCD monitor fully.

3 Rotate the BRIGHT Wheel until the appropriate

brightness is reached.

LCD Monitor

Monitor Opening Button

Brightness Adjustment Of The

Display

BR I GHT

BRIGHT Wheel

CU-VH1E.book Page 12 Friday, March 26, 2004 1:55 PM

EN 13

Master Page: Right

The date/time display can be turned on or off during

playback. (墌 pg. 26, 29)

1 Set the Power Switch to “ON” while pressing

down the Lock Button located on the switch.

2 Open the LCD monitor fully.

3 Press MENU. The Menu

Screen appears.

4 Press R or T to select

“n” (DISPLAY), and press

MENU. The DISPLAY

Menu appears.

5 Press R or T to select

“CLOCK ADJ.”, and press

MENU. The parameter for

“Month” is highlighted.

6 Press R or T to input the

month, and press MENU.

Repeat to input the day,

year, hour and minute.

7 Press R or T to select

“BRETURN”, and press

MENU twice. The Menu

Screen closes.

Date/Time Settings

Power Switch

MENU Button

R T Button

O V E

OF. –ARR DV N F

E C–MOD RE

ONCO Y P –

OFPU

IN S/ V T F–

NRETUR

DMSO N EO

L.V.DENA I

ST RE–EO

SERA CM I

Y IS

L D P

NRETUR

–

OFMET–/TI DA E F

OFDEM– CO TI E

DE OK CL C 2 C

J AD .

3:5

5'0 4

0 PM

NCREON S E

NRETUR

CL C 2

AD . 3:5

5'0 4

0 PM

DEC

YIS LDPA

GETTING STARTED

CU-VH1E.book Page 13 Friday, March 26, 2004 1:55 PM

14 EN

Master Page: Left

The player needs to be powered up to load or eject a

cassette

1 Slide and hold OPEN/EJECT in the direction of

arrow, then pull the cassette holder cover open

until it locks. The cassette holder opens

automatically.

● Do not touch internal components.

2 Insert or remove a tape and press “PUSH HERE”

to close the cassette holder.

● Be sure to press only the section labelled

“PUSH HERE” to close the cassette holder;

touching other parts may cause your finger to

get caught in the cassette holder, resulting in

injury or product damage.

● Once the cassette holder is closed, it recedes

automatically. Wait until it recedes completely

before closing the cassette holder cover.

● When the battery pack’s charge is low, you

may not be able to close the cassette holder

cover. Do not apply force. Replace the battery

pack with a fully charged one or use AC power

before continuing.

3 Close the cassette holder cover firmly until it

locks into place.

To protect valuable recordings…

Slide the erase protection tab on the back of the tape

in the direction of “SAVE”. This prevents the tape

from being recorded over. To record on this tape,

slide the tab back to “REC” before loading it.

Approximate recording time

To switch the recording mode, refer to pages 26 and

27.

NOTES:

● It takes a few seconds for the cassette holder to

open. Do not apply force.

● If you wait a few seconds and the cassette holder

does not open, close the cassette holder cover and

try again. If the cassette holder still does not open,

turn the player off then on again.

● If the tape does not load properly, open the

cassette holder cover fully and remove the

cassette. A few minutes later, insert it again.

● When the player is suddenly moved from a cold

place to a warm environment, wait a short time

before opening the cassette holder cover.

● Closing the cassette holder cover before the

cassette holder recedes may cause damage to the

player.

● Even when the player is switched off, a cassette

can be loaded or unloaded. After the cassette

holder is closed with the player switched off,

however, it may not recede. It is recommended to

turn the power on before loading or unloading.

● When resuming recording, once you open the

cassette holder cover a blank portion will be

recorded on the tape or a previously recorded

scene will be erased (recorded over) regardless of

whether the cassette holder came out or not. See

“Recording From The Middle Of A Tape”

(墌 pg. 34).

Loading A Cassette

/Unloading A Cassette

Make sure the

window side is

facing up.

Cassette holder

cover

OPEN/EJECT

Switch

PUSH HERE

Cassette

holder

Erase protection tab

Tape

Recording mode

SP LP

30 min. 30 min. 45 min.

60 min. 60 min. 90 min.

80 min. 80 min. 120 min.

CU-VH1E.book Page 14 Friday, March 26, 2004 1:55 PM

EN 15

Master Page: Right

1 Make sure the player’s power is off.

2 Slide to open the card cover (MEMORY CARD).

3 To load a memory card, firmly insert it with its

clipped edge first.

To unload a memory card, push it once. After the

memory card comes out of the player, pull it out.

● Do not touch the terminal on the reverse side

of the label.

4 Close the card cover.

To protect valuable files (available only for SD

Memory Card)…

Slide the write/erase protection tab on the side of the

memory card in the direction of “LOCK”. This

prevents the memory card from being recorded over.

To record on this memory card, slide the tab back to

the position opposite to “LOCK” before loading it.

NOTES:

● Be sure to use only SD Memory Cards marked

“” or MultiMediaCards marked

“”.

● Some brands of memory cards are not compatible

with this player. Before purchasing a memory

card, consult its manufacturer or dealer.

● Before using a new memory card, it is necessary to

FORMAT the card. (墌 pg. 25)

TTENTION:

Do not insert or remove the memory card while the

player is turned on, as this may cause the memory

card to be corrupted or cause the player to become

unable to recognise whether or not the card is

installed.

Loading A Memory Card

/Unloading A Memory Card

Memory card

Clipped edge

Card Cover

(MEMORY CARD)

Label

Information On SD Memory Card

SD Memory Cards up to 64 MB have been verified

for use with this player. (As of October 2003)

Write/erase protection tab

GETTING STARTED

CU-VH1E.book Page 15 Friday, March 26, 2004 1:55 PM

Master Page: Left-start

16 EN

VIDEO PLAYBACK

1 Open the LCD monitor fully.

● Set the Video Output Mode Switch to “LCD

MONITOR”. (墌 pg. 11)

2 Load a cassette. (墌 pg. 14)

3 Set the Playback Mode Switch to “VIDEO”.

4 Set the Power Switch to “ON” while pressing

down the Lock Button located on the switch.

5 To start playback, press 4/9.

6 To stop playback, press 8.

● During Stop mode, press 3 to rewind, or

5 to fast-forward the tape.

Maximum continuous playback time

*Provided

NOTES:

● Clean the video heads using an optional dry

cleaning cassette when:

• No picture during playback.

• Blocks of noise appear during playback.

For details, 墌 pg. 52.

● If Stop mode continues for 5 minutes when power

is supplied from a battery, the player shuts off

automatically. To turn on again, set the Power

Switch to “OFF”, then “ON”.

● The playback picture can be viewed in the LCD

monitor or on a connected TV. (墌 pg. 18)

● LCD monitor indications:

• When power is supplied from a battery: the

“” battery indicator is displayed. (墌 pg. 47)

• When power is supplied from an AC outlet: the

“” battery indicator does not appear.

● When a cable is connected to the S, AUDIO (L/R),

VIDEO or headphone connector, sound cannot be

heard from the speaker.

To control the speaker volume…

Rotate the VOLUME Wheel towards “+” to turn up

the volume, or towards “–” to turn down the

volume.

Still Playback

Pauses during video playback.

1) Press 4/9 during playback.

2) To resume normal playback, press 4/9 again.

● If still playback continues for more than about

3 minutes, the player’s Stop mode is

automatically engaged.

● When 4/9 is pressed, the image may not

pause immediately while the player stabilises

the still image.

Frame-By-Frame Playback

Allows frame-by-frame search during video

playback. This feature is available only with a tape

recorded in DV recording mode.

1) Press 4/9 during playback.

2) Press R for forward and T for reverse.

Normal Playback

Battery pack DV mode HD/SD mode

BN-V416U* 1 hr. 40 min. 1 hr. 30 min.

BN-V428U 3 hr. 2 hr. 50 min.

Speaker

Play/Pause Button (4/9)

Rewind Button (3)

Playback Mode

Switch

Power Switch

Stop Button (8)

VOLUME Wheel

Fast-Forward Button (5)

BLANK SEARCH

Button

CU-VH1E.book Page 16 Friday, March 26, 2004 1:55 PM

EN 17

Master Page: Right

Shuttle Search

Allows high-speed search in either direction during

video playback.

1) During playback, press 5 for forward search,

or 3 for reverse search.

2) To resume normal playback, press 4/9.

● During playback, press and hold 5 or 3 .

The search continues as long as you hold the

button. Once you release the button, normal

playback resumes.

● A slight mosaic effect appears on the display

during Shuttle Search. This is not a

malfunction.

TTENTION:

(DV mode only)

During Shuttle Search, parts of

the picture may not be clearly

visible, particularly on the left

side of the screen.

Blank Search

Helps you find where you should start recording in

the middle of a tape to avoid time code interruption.

(墌 pg. 34)

1 Load a cassette. (墌 pg. 14)

2 Set the Playback Mode Switch to “VIDEO”.

3 During Stop mode,

press BLANK

SEARCH.

● The “BLANK

SEARCH”

indication appears

and the player

automatically starts

reverse or forward search, then stops at the

spot which is about 3 seconds of tape before

the beginning of the detected blank portion.

● To cancel Blank Search midway, press 8.

NOTES:

● Before starting Blank Search, if the current position

is at a blank portion, the player searches in the

reverse direction. If the current position is at a

recorded portion, the player searches in the

forward direction.

● Blank Search does not work if “USE CLEANING

CASSETTE” has appeared with the tape.

● If the beginning or end of the tape is reached

during Blank Search, the player stops

automatically.

● A blank portion which is shorter than 5 seconds of

tape may not be detected.

● The detected blank portion may be located

between recorded scenes. Before you start

recording, make sure there is no recorded scene

after the blank portion.

Slow-Motion Playback

Playback Zoom

Available only with the remote control (provided).

(墌 pg. 38, 39)

BLANK SEARCH

PUSH "STOP" BUTTON

TO CANCEL

VIDEO PLAYBACK

CU-VH1E.book Page 17 Friday, March 26, 2004 1:55 PM

18 EN

Master Page: Left

These are some basic types of connections. When

making the connections, refer also to your VCR and

TV instruction manuals.

To Connect A Conventional TV or VCR

* Connect when your TV/VCR has S-VIDEO IN

and A/V input connectors. In this case, it is not

necessary to connect the yellow video cable.

** Connect when your TV/VCR has only A/V input

connectors.

*** Not required for watching still images only.

To Connect To A TV or VCR Equipped With The

Component Video Connectors

* Not required for watching still images only.

Connections To A TV Or VCR

COMPONENT

VIDEO

OUT

COMPONENT

VIDEO

OUT

VIDEOVIDEO AUDIOAUDIOLLRR

PbPb PrPr

VCR

A To S-VIDEO IN*

B Yellow to VIDEO IN**

C White to AUDIO L IN***

D Red to AUDIO R IN***

BCD

To S

S-Video cable

(provided)

To AUDIO/

VIDEO

Audio/Video cable

(provided)

COMPONENT

VIDEO

OUT

COMPONENT

VIDEO

OUT

VIDEOVIDEO AUDIOAUDIOLLRR

PbPb PrPr

Wide-screen TV or

high definition TV

VCR

A Not required for connection.

B White to AUDIO L IN*

C Red to AUDIO R IN*

D To component video connectors

To AUDIO

To Y/Pb/Pr

Component video cable

(provided)

Audio/Video

cable

(provided)

RCA-BNC

Adapter

VIDEO PLAYBACK (cont.)

CU-VH1E.book Page 18 Friday, March 26, 2004 1:55 PM

EN 19

Master Page: Right

1 Make sure all units are turned off.

2 Connect the player to a TV or VCR as shown in

the illustration.

If using a VCR, go to step 3.

If not, go to step 4.

3 Connect the VCR output to the TV input,

referring to your VCR’s instruction manual.

4 For S-video or video connection

Set “S/VIDEO” to “16:9 TV” or “4:3 TV”

depending on the aspect ratio of the TV you are

connecting. (墌 pg. 26, 28)

● Set the Video Output Mode Switch to “LCD

MONITOR”.

For component video connection

● Set “Y/Pb/Pr” to any picture size depending on

the TV to which you are connecting.

(墌 pg. 26, 28)

● Set the Video Output Mode Switch to

“COMPONENT VIDEO OUT”.

5 Turn on the VCR and the TV.

6 Set the VCR to its AUX input mode, and set the

TV to appropriate input mode.

To choose whether or not the following displays

appear on the connected TV…

● Date/Time

Set “DATE/TIME” to “AUTO”, “ON” or “OFF”.

(墌 pg. 26, 29)

Or, press DISPLAY on the remote control to turn

on/off the date indication.

● Time Code

Set “TIME CODE” to “ON” or “OFF”.

(墌 pg. 26, 29)

● Indications other than date/time and time code

Set “ON SCREEN” to “OFF”, “LCD” or “LCD/TV”.

(墌 pg. 26, 29)

NOTES:

● It is recommended to use the AC Power Adapter/

Charger as the power supply instead of the

battery pack. (墌 pg. 10)

● Make sure you adjust the TV sound volume to its

minimum level to avoid a sudden burst of sound

when the player is turned on.

● If you have a TV or speakers that are not specially

shielded, do not place the speakers adjacent to the

TV as interference will occur in the player

playback picture.

● During playback in HD mode, the images may not

appear on the player’s LCD monitor if the

component video cable is connected.

● When a cable is connected to the S, AUDIO (L/R),

VIDEO or headphone connector, sound cannot be

heard from the speaker.

● According to the type of the connected TV and the

recording mode, the playback picture may be

squeezed vertically or horizontally. For details,

refer to the Instructions of the TV.

VIDEO PLAYBACK

CU-VH1E.book Page 19 Friday, March 26, 2004 1:55 PM

Master Page: Left-start

20 EN

DIGITAL STILL CAMERA (D.S.C.) PLAYBACK

D.S.C. PLAYBACK

You can view the stored images in the memory card,

one at a time, much like flipping through a photo

album.

1 Open the LCD monitor fully.

● Set the Video Output Mode Switch to “LCD

MONITOR”. (墌 pg. 11)

2 Load a memory card. (墌 pg. 15)

3 Set the Playback Mode Switch to “MEMORY”.

4 Set the Power Switch to “ON” while pressing

down the Lock Button located on the switch.

● The still image which has been played back at

the last time is displayed.

5 Press 3 to display the previous file. Press 5

to display the next file.

● Pressing INFO gives you details on the

displayed file. (墌 pg. 21)

● You can also look for the desired file using

Index Screen. (墌 pg. 21)

● You can turn off the on-screen playback

display. (墌 pg. 21)

NOTES:

● Images shot in a file size other than “640 x 480”,

“848 x 480”, “1280 x 720” and “1280 x 960”

with another devices will be displayed thumbnail

images. These thumbnail images cannot be

transferred to a PC.

● Images shot with devices (such as JVC GR-DVX7)

that are not compatible with DCF cannot be

viewed with this player; “UNSUPPORTED FILE!”

will be displayed.

Playback Zoom

Available only with the remote control (provided).

(墌 pg. 39)

You can run through all the images stored in

memory card automatically.

1 Perform steps 1 – 4 in “Normal Playback Of

Images”.

2 Press 4/9 to start Auto Playback. Files are

displayed in descending order.

● If you press 3 during Auto Playback, files

are displayed in ascending order.

3 To end Auto Playback, press 8.

Normal Playback Of Images

INFO Button

Play/Pause Button (4/9)

Rewind Button (3)

Playback Mode

Switch

Power Switch

Stop Button (8)

Fast-Forward Button (5)

INDEX Button

MENU Button/

R T Button

Auto Playback Of Images

[For Normal Playback]

To display the next image

[For Auto Playback]

Image playback screen

To display the previous image

100-0013

100-0014

100-0015

100-0016

CU-VH1E.book Page 20 Friday, March 26, 2004 1:55 PM

Page is loading ...

JVC LYT1300-001A User manual

Brand: JVC

Model: LYT1300-001A

Category: Cassette players

Type: User manual

Download PDF

report

JVC LYT1300-001A User manual

JVC LYT1300-001A User manual

Related papers

Other documents