Martin EC 20 Installation guide

Type
Installation guide

This manual is also suitable for

Martin EC 20 is a flightcase designed for flexibility and ease of use in various applications. It features a modular design, allowing you to customize the case to fit your specific requirements. The case can be used in a variety of orientations, including horizontally at angles up to +/- 20° to form a concave or convex wall. To achieve this, the EC-Series Curving Kit is required, which includes thumbwheels, locknuts, and curved plates. The case can be suspended vertically or stacked horizontally, making it suitable for both portable and fixed installations.

Martin EC 20 is a flightcase designed for flexibility and ease of use in various applications. It features a modular design, allowing you to customize the case to fit your specific requirements. The case can be used in a variety of orientations, including horizontally at angles up to +/- 20° to form a concave or convex wall. To achieve this, the EC-Series Curving Kit is required, which includes thumbwheels, locknuts, and curved plates. The case can be suspended vertically or stacked horizontally, making it suitable for both portable and fixed installations.

EC Series Curving Kit
Installation Guide
WARNING! Before installing an EC Series Curving Kit, Read “Safety Information” on page 3 of the EC
Series Safety and Installation Guide supplied with EC Series flightcases and available for download
free of charge from the EC-20 Support page on www.martin.com.
WARNING! The safety and suitability of lifting equipment, installation location, anchoring method,
mounting hardware, suspension structures and electrical installation is the responsibility of the
installer. All local safety regulations and legal requirements must be observed when installing and
connecting the EC Series Headers.
WARNING! Installation must be carried out by qualified professionals only. Contact your Martin
supplier for assistance if you have any questions about how to install this product safely.
EC-20 Headers and panels can be attached horizontally at up to +/- 20° angles to form a convex or concave
wall using the EC-Series Curving Kit (P/N 90354270).
Unpacking
The EC Series Curving Kit is supplied in a cardboard box. Curving Kit components can be stored in an EC-20
8-unit Flightcase. Each Kit contains:
50 x EC Series Curving Plate Locking Thumbwheels
50 x locknuts for thumbwheels
25 x EC Series Curving Plates (‘Bananas’)
1 x EC Series Curving Kit Installation & Safety Guide
Side-to-side attachment in a curved wall
To install panels in a curved configuration:
1. See Figure 1. Unscrew the 2.5 mm Allen bolts shown and
remove the straight side-to-side alignment cones B and
washers A close to the top and to the bottom of one side of
each panel. Store all components for possible re-use.
2. Remove the similar alignment cones from the Headers.
3. Suspend the panels vertically as described in the EC Series
user manual.
TM
©2010 Martin Professional A/S. Information subject to change without notice. Martin Professional A/S and all affiliated companies disclaim liability for
any injury, damage, direct or indirect loss, consequential or economic loss or any other loss occasioned by the use of, inability to use or reliance on the
information contained in this manual. The Martin logo, the Martin name and all other trademarks in this document pertaining to services or products by
Martin Professional A/S or its affiliates and subsidiaries are trademarks owned or licensed by Martin Professional A/S or its affiliates or subsidiaries.
P/N 35000612, Rev. C
Figure 1: Removing side-to-side
alignment cones
4. See Figure 2. Install the thumbwheels A
supplied in the Kit on the top and
bottom profiles of each panel, using the
supplied locknuts to secure them in
place so that they will not drop out of
the panel if loosened too much.
5. Insert two curved plates (or ‘bananas’)
B supplied in the Kit in their slots on the
top and bottom profiles. Once the
correct angle is obtained, lock the
columns by tightening thumbwheels A.
6. Install curving plates using the same
method in the slots in the bottom profile
of the Headers.
7. When the installation is disassembled,
the thumbwheels A can be tightened
and left in position but remove the ‘bananas’ B and store them safely in the flightcase for possible
re-use.
8. Reinstall the alignment cones (see Figure 1) on the sides of panels and Headers before installing panels
in a flat wall.
All EC Series and P3 system controller user documentation is available for download free of charge from
the Product Support area at www.martin.com.
Figure 2: Locking panel angles in a curved array
www.martin.com Olof Palmes Allé 18 8200 Aarhus N Denmark
Tel: +45 8740 0000 Fax +45 8740 0010
  • Page 1 1
  • Page 2 2

Martin EC 20 Installation guide

Type
Installation guide
This manual is also suitable for

Martin EC 20 is a flightcase designed for flexibility and ease of use in various applications. It features a modular design, allowing you to customize the case to fit your specific requirements. The case can be used in a variety of orientations, including horizontally at angles up to +/- 20° to form a concave or convex wall. To achieve this, the EC-Series Curving Kit is required, which includes thumbwheels, locknuts, and curved plates. The case can be suspended vertically or stacked horizontally, making it suitable for both portable and fixed installations.

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI