2. SuperFish
  3. Koi Pro Combi Drum
Koi Pro Combi Drum

SuperFish Koi Pro Combi Drum User guide

  • Hello! I've reviewed the user guide for the Motor Koi Pro Combi Drum. This document provides detailed, step-by-step instructions on how to replace the motor of the filter, including its disassembly and reassembly, with specific torque requirements. I'm ready to answer any questions you have about the process.
  • What tools are needed to replace the motor?
    What should be done before starting the motor replacement?
    How should the new motor be oriented during replacement?
User guide
Motor replacement
of the Koi Pro Combi Drum
Unplug everything so that there is no power on the
electronics. See to it that the water isout of the  lter
as much as possible, so that no water can come into
contact with the electronicsduring (dis)assembly.
pipe wrench.
Now there are 2 options regarding the position in
which the motor is mounted: if the white coilis up as
in photo 4, then continue with step 6. If the white coil
is down as in photo 3, then continue with step 5.
Start with removing the cap of the motor
by unscrewing the hex head bolts (Photo step 1)
If the white coil is down, it is di cult to reach the
locknut of the shaft. To have good access to it,
completely loosen the 2 boltsholding the coil (Photo
step 3) so that you can remove the coil completely. As
you replace the complete motor, there is no need for
keeping the coil on.
Unscrew the electric wires and remove them from
the terminal block (Photo step 2). Then unscrewthe
ground wire (Photo step 3) and put the cover with
the wires stuck in it to one side.
Loosen the locknut (17mm) of the shaft
(Photo step 5) while holding the drum so that
it cannot rotate.
Replacement of the motor of the Koi Pro Combi Drum
To replace the motor of the Combi Drum, you need the following tools:
hex keys - small screwdriver - Phillips screwdriver - wrenches - torque wrench - pipe wrench.
Step 1
Step 4
Step 2
Step 5
Step 3
Step 6
09-2022 ER
www.aquadistri.com
Vlietweg 8, NL-4791 EZ Klundert
The Netherlands, [email protected]om
Now loosen the bolts holding the motor to the  lter
(Photo step 6).
Now tighten the locknut of the shaft with a torque
wrench at 65 Nm (Photo step 8); again make sure
that you (better yet, someone ho helps) hold the
drum so that it cannot rotate with it.
Attach the supplied cable shoes over the contacts on
the motor (it does not matter where the brown and
blue wire are, Photo step 12) and screw them back
into the terminal block (Photo step 13).
Remove the locknut completely and carefully remove
the motor from the shaft. Make sure that the seal
ring around the shaft does not fall and you lose it.
Then loosen the two screws on the new motor (Photo
step 9) and turn the motor 180° so that the coil is
pointing down again (Photo step 10). Make sure that
the black ring in this block remains in the right place.
Now place the new motor over the shaft
(Photo step 7) and screw the motor back to the  lter
wall with the hex head bolts as it was (Photo step 6)
Screw the motor in this position, reconnecting the
ground wire (Photo step 11).
Motor Replacement of the Koi Pro Combi Drum
Step 7
Step 10
Step 13
• Now screw the protective cap back on as it was (Photo step 1).
• Let water  ow into the  lter again and check that everything is watertight.
• Then turn everything on and check for proper operation.
• Your  lter is now ready for normal use again.
Final instructions
Step 11 Step 12
Step 8Step 9
Für Deutsch, scannen Sie den QR
Pour le français, scannez le QR
Voor Nederlands, scan de QR
/