1. Carefully remove all parts from the box. Place on a clean, soft surface.
2. Remove collar loop (D) from chain (H) by unscrewing quick link (G).
3. Install mounting plate (J) to junction box and secure with mounting
screws (C).
4. Secure collar loop (D) to mounting plate (B) using pliers to tighten
locknut.
5. Install canopy (E) to collar loop (D) and secure with collar ring (F).
6. Determine desired overall length, and amount of chain (H) needed.
Shorten chain using chain pliers. (Keep extra chain)
7. Attach chain (E) to collar loop (D) and fixture loop (I) using quick
links (G). Secure quick links (H).
8. Attach chains (J) to hooks on fixture body (K) and hooks on the
bottom of fixture loop (I).
9. Thread fixture wire and ground wire through chain (J) and chain (H).
NOTE: When you reach the collar loop (D), ensure there is no tension
on the wires. Cut excess wires, being sure to leave about 12” to reach
the junction box.
Talia Large Linear Chandelier
Item # JN 5117
ASSEMBLY INSTRUCTIONS
This light fixture should be installed in accordance with all applicable,
local installation codes, and by a person familiar with the construction
and operation of it, as well as the hazards involved. Inspect item and
contents carefully. If any damage or defect is found, do not install.
Retain all packaging material until installation is complete and approved.
TOOLS REQUIRED (NOT INCLUDED):
Phillips Screwdriver Slotted Screwdriver Chain Pliers
Slip Joint Pliers Measuring Tape Wire Cutters
Wire Strippers
NOTICE:
Diagram 1
A
B
C
D
E
F
H
G
G
I
K
Bulbs not included
J
US
M
L
I
D
S
E
T
Talia Large Linear Chandelier
Item # JN 5117
ASSEMBLY INSTRUCTIONS
This light fixture should be installed in accordance with all applicable,
local installation codes, and by a person familiar with the construction
and operation of it, as well as the hazards involved. Inspect item and
contents carefully. If any damage or defect is found, do not install.
Retain all packaging material until installation is complete and approved.
10. Separate two sides of molded wire, and strip insulation on each 5/8".
11. Loosen collar ring (F) and let canopy (E) slip down chain (H) carefully.
12. Twist all fixture wires together. Slip through center hole of collar
loop (D).
NOTE: Untwist wires and separate to prepare for connection.
13. Wrap fixture ground wire (bare copper) around the green grounding
screw (see diagram 1). Tighten. Continue fixture ground wire and
connect to supply ground wire (usually green or bare copper) using
wire nut (A).
NOTE: It is imperative that the fixture is grounded.
14. Connect fixture neutral wire (ribbed) to the supply neutral wire (usually
white) using wire nut (A).
15. Connect fixture hot wire (smooth with markings) to the supply hot
wire (usually black) using wire nut (A).
CAUTION: Do not reverse the hot and neutral connections.
16. Make sure all wire connections are tight, then carefully tuck into the
junction box.
17. Install canopy (E) to collar loop (D) and secure with collar ring (F).
18. Insert light bulbs into the sockets.
19. Install glass balls starting from bottom (layer 4) and working your
way to the top (layer 1) as shown in figures L4-L1.
Care Instructions: Clean only with a soft dry cloth or feather duster. Do
not use abrasive or chemical agents..
NOTICE:
Diagram 1
A
B
C
D
E
F
H
G
G
I
K
Bulbs not included
J
US
M
L
I
D
S
E
T
L1
L2
L3 L4
110mm
137mm
163mm
S 26pcs
M 42pcs
L 29pcs
Talia Large Linear Chandelier
Item # JN 5117
ASSEMBLY INSTRUCTIONS
This light fixture should be installed in accordance with all applicable,
local installation codes, and by a person familiar with the construction
and operation of it, as well as the hazards involved. Inspect item and
contents carefully. If any damage or defect is found, do not install.
Retain all packaging material until installation is complete and approved.
NOTICE:
US
M
L
I
D
S
E
T
L3
L4
M
M
M
M
M
M
M
M
L
L
L
L
L
L
L
L
L
S
S
S
S
S
S
Talia Large Linear Chandelier
Item # JN 5117
ASSEMBLY INSTRUCTIONS
This light fixture should be installed in accordance with all applicable,
local installation codes, and by a person familiar with the construction
and operation of it, as well as the hazards involved. Inspect item and
contents carefully. If any damage or defect is found, do not install.
Retain all packaging material until installation is complete and approved.
NOTICE:
US
M
L
I
D
S
E
T
M
M
M
M
M
M
M
M
M
M
M
M
MMMM
M
M
S
SS
S
S
S
M
M
M
M
M
M
M
M
MM
MM
M
M
S
S
S
S
S
S
S
S
S
S
S
S
LLL
L
L
L
L
L
L
L
L
L
L
L
L
L
L
L
L1
L2
Talia Large Linear Chandelier
Item # JN 5117
ASSEMBLY INSTRUCTIONS
This light fixture should be installed in accordance with all applicable,
local installation codes, and by a person familiar with the construction
and operation of it, as well as the hazards involved. Inspect item and
contents carefully. If any damage or defect is found, do not install.
Retain all packaging material until installation is complete and approved.
NOTICE:
US
M
L
I
D
S
E
T
-
1
-
2
-
3
-
4
-
5
Ask a question and I''ll find the answer in the document
Finding information in a document is now easier with AI
Related papers
-
VISUAL COMFORT SK 5555 User manual
-
-
-
-
-
-
-
-
VISUAL COMFORT JN 4110 User manual
-
Other documents
-
Ralph Lauren RL5790 Ancram Large Empire Chandelier Operating instructions
-
-
circa LIGHTING PCD 5115 User manual
-
Visual Comfort Studio CHC 1474GI-NP Installation guide
-
-
-
circa LIGHTING RL 5131 User manual
-
-
circalighting ARN5500 Installation guide
-
