Aputure LS 600c Pro User manual

Brand: Aputure

Model: LS 600c Pro

Type: User manual

Aputure LS 600c Pro is a professional RGBWW COB light that delivers powerful color-accurate illumination. With fully tunable CCT from 2300K to 10000K, it offers various light modes including CCT, HSI, XY, RGB, GEL, SOURCE, and professional control options like Sidus Link, DMX512/RDM, Lumenradio CRMX, and Ethernet.

Product Manual

English

LS 600c Pro

When using this unit, basic safety precautions should always be followed, including the

following:

1. Read and understand all instructions before using.

2. Close supervision is necessary when any xture is used by or near children. Do not leave

the xture unattended while in use.

3. Care must be taken as burns can occur from touching hot surfaces.

4. Do not operate the xture if a cord is damaged, or if the xture has been dropped or

damaged, until it has been examined by qualied service personnel.

5. Position any power cables such that they will not be tripped over, pulled, or put into

contact with hot surfaces.

6. If an extension cord is necessary, a cord with an amperage rating at least equal to that of

the xture should be used. Cords rated for less amperage than the xture may overheat.

7. Always unplug the lighting xture from the electrical outlet before cleaning and servicing,

or when not in use. Never yank the cord to remove the plug from the outlet.

8. Let the lighting xture cool completely before storing. Unplug the power cable from

lighting xture before storing and store the cable at assigned space of the carrying case.

9. To reduce the risk of electric shock, do not immerse this xture in water or any other

liquids.

10. To reduce the risk of re or electric shock, do not disassemble this xture. Contact

[email protected] or take the lighting xture to qualied service personnel when service

or repair is required. Incorrect reassembly may cause electric shock when the lighting

xture is in use.

11. The use of any accessory attachment not recommended by the manufacturer may increase

the risk of re, electric shock, or injury to any persons operating the xture.

12. Please power this xture by connecting it to a grounded outlet.

13. Please remove the protective cover before use.

14. Please remove the protection cover before using the reector.

15. Please do not block the ventilation or donot look at the LED light

source directly when it is powered on. Please do not touch the

LED light source in any condition.

-1-

Introduction

Thank you for purchasing the Aputure® "Light Storm" series RGBWW COB light - LS 600c

Pro. LS 600c Pro is a high power full color light source with Fully Tunable CCT from

2,300K to 10,000K, supporting CCT, HSI, XY, RGB, GEL, SOURCE light mode, and

professional control with Sidus Link, DMX512/RDM, Lumenradio CRMX, Ethernet. The LS

600c Pro brings you a more comprehensive and professional lighting solution with

intelligent power supply and cinematic control, granting you true creative freedom.

CAUTION

DO NOT TOUCH LED

Light Source Surface

IMPORTANT SAFETY INSTRUCTIONS

-2-

FCC Compliance Statement

SAVE THESE INSTRUCTIONS

16. Please do not place the LED lighting xture near any ammable object.

17. Only use a dry microber cloth to clean the product.

18. Please do not use the light xture in wet condition on account of electric shock may be

caused.

19. Please have the product checked by an authorized service personnel agent if the product

has a problem. Any malfunctions caused by unauthorized disassembly are not covered

by the warranty. The user may pay for maintenance.

20. We recommend only using the original Aputure cable accessories. Please note that any

malfunctions casued by using unauthorized accessories are not covered by the warranty.

The user may pay for maintenance.

21. When hanging the product overhead, always ensure an extra safety measure has been

attached - such as a safety chain- that is certied for the weight of the product.

22. This product is certied by RoHS, CE, KC, PSE, and FCC. Please operate the product

in full compliance with relevant country's standards. Any malfunctions caused by incorrect

use are not covered by warranty. The user may pay for maintenance.

23. The instructions and information in this manual are based on thorough, controlled

company testing procedures. Further notice will not be given if the design or specications

change.

WARNING

Changes or modications not expressly approved by the party responsible for compliance

could void the user's authority to operate the equipment.

NOTICE

This equipment has been tested and found to comply with the limits for a Class B digital

device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide

reasonable protection against harmful interference in a residential installation. This

equipment generates, uses, and can radiate radio frequency energy and, if not installed

and used in accordance with the instructions, may cause harmful interference to radio

communications. However, there is no guarantee that interference will not occur in a

particular installation.

If this equipment does cause harmful interference to radio or television reception, which

can be determined by turning the equipment o and on, the user is encouraged to try

reorient or relocate the receiving antenna.

-3-

Increase the separation between the equipment and receiver.

Connect the equipment to an outlet on a dierent circuit than the receiver is connected

to.

Consult the dealer or an experienced radio/TV technician for help.

This device has been evaluated to meet general RF exposure requirements.

RF Warning Statement:

-4-

The illustrations in the manual are only diagrams for reference. Due to the continuous

development of new versions of the product, if there are any dierences between the

product and the user manual diagrams, please refer to the product itself.

LS 600c Pro

Lamp Head (1pc)

LS 600c Pro

Control Box (1 pc)

Lightning Clamp

(1 pc)

LS 600c Pro Rolling

Carrying Case (1 pc)

Paracord

Strap(1 pc)

LS 600 Series 7-Pin Weatherproof

Head Cable (7.5m)(1 pc)

Neutrik® powerCON AC

Power Cable (6m) (1 pc)

600 Series

Hyper Reector (1 pc)

Protection

Cover (1 pc)

Components List

Please make sure all accessories listed below are found before using. If not, contact your

seller immediately.

-5-

Product Details

1. Lamp Head

Bowens Mount

600 Series

Hyper Reector

600W RGBWW COB chipset

Ratcheting Disk

Brake Handle

Bowens Mount

Release button

7-Pin Male Weatherproof

Head Cable Connector

Junior/Baby Pin Mount

(1.125in/28mm | 5/8in./16mm)

Cable Relief Hook

T-Handle / Baby Pin Mounting Screw

2. Control Box

Paracord Strap Plate

LCD Display

Menu Button

Preset Button

Light Mode Button

Back Button

Select Wheel

Power Button

Antenna Box

Battery Plate

(*Anton Bauer or

V-mount)

USB Port

Floor Stand

Lightning Clamp

Quick-Release Plate

EtherCON RJ45

-6-

DMX IN

Port

DMX OUT

Port

Neutrik®

powerCON

AC Input

7-Pin Female Head Cable Connector

48V DC Input

(3-Pin XLR)

Setting Up the Light

1. Attaching/detaching the Protection Cover

Press the release button following the arrow and rotate the cover clockwise to detach

the cover. To reattach the cover, insert it into the Bowens mount and rotate counter-

clockwise.

2. Attaching/detaching the Bowens Mount Hyper Reector

(LS 600 Series)

To install the reector, press the release button, insert the reector into the Bowens mount,

and rotate it counterclockwise as shown in the following pictures. To remove the reector,

pull back the release button and rotate the reector clockwise.

WARNING

Always remove the protection cover prior to turning on the light. Always re-install

the cover when packing it away.

Top Bottom

-7-

3. Setting Up the Lamp Head

If using a 5/8in / 16mm stand (Baby Pin), then mount the Lamp Head onto the stand,

and x it in place using the T-Handle/Mounting Screw on the Baby Pin Receiver.

If using a 1.125in / 28mm stand (Junior Pin), then mount the Lamp Head into the Junior

Pin receiver, and x it in place using the T-Handle on the stand. Loosen or tighten the

handbrake locking mechanism on the yoke to adjust the xture's angle of tilt.

4. Lightning Clamp Operation Instructions

1) Clamp the Lightning Clamp onto a light stand.

2) To attach the control box, rotate the release lever to unlock the quick-release plate, then

mount the control box onto the Lightning Clamp (the release lever will spring back).

3) To remove the control box, grasp it rmly, then unlock the quick-release plate by turning

the release lever, and detach the control box.

-8-

AC 100V-240V

5. Connecting the Lamp Head to the Control Box

Connect the Lamp Head to the control box using the 7-pin Weatherproof Connecting

Cable.

Hang the cable using the rope to manage

and reduce tension on the cable.

* Disconnect the Head Cable by pulling up the collar on the connector. This will disengage its locking

mechanism. Do not pull directly.

1) Powering by AC

6. Powering Up the Control Box

*To disconnect the Neutrik® powerCon cable, pull back on the silver release tab on the cable connector,

and rotate the connector counter clockwise. Do not pull directly.

-9-

2) Powering by DC

* You can choose V-Mount or Anton Bauer Battery as required.

V-Mount Battery Anton Bauer Battery

7. Charging Batteries Using the Control Box

You can charge batteries via built-in Battery Plates, the maximum intensity that the light

can operate at while charging batteries are as follows:

Exponential(Exp) or Linear: ≤70%

Logarithmic(Log): ≤30%

S-Curve: ≤55%

DC Supply

48V-15A

3pin XLR

3) Powering by DC Supply

-10-

CCT

100%

2000K

M-1

M+1

10000K

-0.05

G/M

：

CCT

6200K

：

INT

60%

1. Turning the Light On and O

2. Manual Control

Operations

Intensity

Correlated Color

temperature

Green/Magenta

adjustment

There are three buttons on the control box for manual control of the light: MENU, LIGHT

MODE, and PRESET.

Press the MENU button to enter the System Menu interface. In the System Menu you'll

nd Output Mode / DMX Mode / Custom FX /Dimming Curves / Fan Mode / Studio

Mode / Control System / Language / Frequency Selection / Product Information /

Update / Factory Reset / Battery Power Option

2.1 MENU

Default Control Screen (CCT Mode)

System Menu Control Screen

2.1.1Output Mode

Press the MENU button to enter the menu interface, rotate the select wheel and short

press to enter the Output Mode.

Constant Output: maintain the brightness output during the process of changing the

color temperature.

DMX Mode

* The fade-out time decreases as the percentage of brightness decreases. When the Intensity

output is 100%, the fade-out time is 60 seconds, which decreases in sequence.

* If the signal is reconnected, the DMX console will continue to maintain the signal output as s

ame as before.

-11-

Output Mode

Constant Output

Maximum Output

DMX Mode

DMX Address

DMX Loss Behavior

DMX Profile

DMX Termination

Max Output: perform at the maximum possible output throughout the CCT range.

2.1.2DMX Mode

Press the MENU button to enter the menu interface, rotate the select wheel and short

press to enter the DMX mode.

DMX address: LS 600c Pro will set to in DMX Address interface. Press and hold the MENU

for 2 seconds to lock the DMX Address. In the locked state, cannot enter

other interfaces, Press and hold SELECT for 2 seconds to unlock.

DMX Loss Behavior: rotate the select wheel to choose Black out /fade to Black /Hold last

setting/ Hold 2 min& fade Out.

Hold last setting -After DMX signal is lost, remember the last control setting.

Black out -when the DMX signal is lost, it will be Black out.

Fade to Black -after DMX signal is lost, it will fade to Black in 60 seconds.

Hold 2 min& Fade Out -After the DMX signal is lost, keep the last control setting for two

minutes, and then Fade to Black within 60 seconds.

DMX Prole : Rotate the Select wheel, and short press to select a desired 8-bit/16-bit DMX

Prole. DMX Termination: toggle Auto-termination on or o.

2.1.3Custom FX

Press the MENU button to enter the menu interface, rotate the select wheel and short

press to enter the Custom FX.

-12-

Custom FX

Picker FX

Music FX

Dimming Curve

Linear

Exp

S-curve

Log

2.1.4) Dimming Curves

Press the MENU button to enter the menu interface, rotate the select wheel and short

press to enter the Dimming Curves. Rotate and short press the wheel to choose

between exponential (Exp) or logarithmic (Log), linear and S-Curve dimming curves.

2.1.5) Fan Mode

Press the MENU button to enter the menu interface, rotate the select wheel and short

press to enter the Fan Mode. rotate and short press the wheel to choose between

Smart, High, Medium and Silent fan mode.

Fan Mode

Silent

High

Medium

Smart

Change the fan speed with

temperature changes.

* Silent: deactivate all fans. Limits output to 60W max.

* When overheat symbol appears on the light control interface, please follow the text underneath to adjust the

Fan Mode to Smart or High. If the internal temperature of the lamp reaches the threshold that needs to be

cooled, the lamp will automatically shut down due to overheat protection.

You can choose to enter Picker FX or Music FX.

Each type can save up to 10 custom FXs. "NO FX" refers to unsaved FX, and "Untitled"

refers to saved FX.

-13-

Bluetooth

Number：FF3BEB

Bluetooth

Bluetooth Reset

YES

2.1.6) Studio Mode

Press the MENU button to enter the menu interface, rotate the select wheel and short

press to enter the Studio Mode. When the studio mode is turned on (ON), the lamp can

be turned on directly, when the studio mode is turned o (OFF), you need to press the

power button to turn on the lamp.

2.1.7) Control System

LS 600c Pro has three remote control methods: Bluetooth, LumenRadio CRMX and

Ethernet. Only one control mode can be used at one time.

2.1.7.2) CRMX

Rotate the select wheel and short press to enter the Lumenradio CRMX, When CRMX

Status is “ON”, it will continuously search for a pairable signal in the background to

connect. “Unpair” will disconnect the currently established connection so that other

signal transmitters can be paired.

2.1.7.1) Bluetooth

Rotate the select wheel and short press to enter the Bluetooth mode. When Bluetooth

is “ON”, the serial number is displayed below, after executing Bluetooth Reset, your

mobile phone or tablet will be able to connect to and control the light with Sidus Link

App.

Studio Mode

-14-

Ethernet

Manual Set IP

Language

简体中文

English

2.1.7.3) Ethernet

Rotate the select wheel and short press to enter the Ethernet mode. You can set

the IP manually in Manual Set IP interface or obtain IP aromatically in Automatic

Obtain IP interface.

2.1.8) Language

Press the MENU button to enter the menu interface, rotate the select wheel and

short press to enter the Language settings. rotate and short press the wheel to

choose English or Simplied Chinese.

2.1.9) Frequency Selection

Press the MENU button to enter the menu interface, rotate the select wheel and short

press to enter the Frequency Selection. Rotate the select wheel to adjust he light

frequency by 100Hz every turn.

CRMX

CRMX Status

Unpair

-15-

Update

Update Firmware

Firmware Version

Product Information

Hardware Version

UID: 6LY00X1000X

2.1.10) Product Information

Press the MENU button to enter the menu interface, rotate the select wheel and

short press to enter Product Information, you can view the Hardware Version

and UID of the product.

2.1.11) Update

Press the MENU button to enter the menu interface, rotate the select wheel and short

press to Update. You can update the rmware in the Update Firmware interface,

and view the Firmware Version. Firmware update can also be done via Sidus Link

app using OTA (Over the Air Technology).

2.1.12) Factory Reset

Press the MENU button to enter the menu interface, rotate the select wheel and

short press to Factory Reset.

Frequency Selection

2000

2.2 Accessing Lighting Modes

-16-

YES

Factory Reset

Battery Power Option

Wake up Batteries

Full Battery Power

Press the LIGHT MODE button on the control box to enter the mode: CCT, HSI, RGB,

XY, RGB, Source, and GEL.

2.1.13) Battery Power Option

Press the MENU button to enter the menu interface, rotate the select wheel and short

press to Battery Power Option.

Wake Up Battery: When you need to activate the lithium battery from overdischarge

protection. Select the lithium battery specication 14.4V/26V and enter the Wake

Up Batteries interface, conrm Activate to output 3A current in order to activate

the lithium battery; After activation, check whether the lithium battery has a voltage

output. If so, the activation is successful, otherwise the activation fails.

Full power output: a single lithium battery meets 360W continuous output (14.4V

lithium battery maximum output current 30A, 26V lithium battery maximum output

current 15A), two lithium batteries can meet the input power requirement of 720W,

and the lamp can achieve 100% illumination Output.

The factory settings list :

Light mode: Intensity 50%, CCT 5600K;

Language: English

Fan Mode: Smart

Dimming Curve: Linear

Studio Mode: OFF

Control System: Bluetooth

DMX: Address 001, Hold Last Settings, DMX Termination OFF

-17-

CCT

100%

2000K

M-1

M+1

10000K

-0.05

G/M

：

CCT

6200K

：

INT

60%

Fire

1 °

2.2.2) Advanced HSI

Press the LIGHT MODE button to enter the light mode interface, rotate the select wheel

and short press to Adv. HSI . You can adjust Intensity (0-100%), Hue(1-360°) Saturation

(0-100%), and Correlated Color Temperature (2300K - 10000K).

2.2.3) FX

Press the LIGHT MODE button to enter the light mode interface, rotate the select wheel

and short press to FX.

You can choose 16 light preset eects: Fire, Strobe, Explosion, Faulty Bulb, Pulsing,

Welding, Cop Car, Color Chase, Party Lights, Firework, Club Lights, Paparazzi,

Lightning, TV and Candle.

Each preset has multiple parameters that can be changed to customize the eects.

2.2.1} CCT

Press the LIGHT MODE button to enter the light mode interface, rotate the select wheel

and short press to CCT. You can adjust Intensity (0-100%), Correlated Color Temperature

(2300K - 10000K), and Green/ Magenta adjustment (-1.0 to +1.0).

-18-

RGB

：

INT

60%

100%

：

100%

X Y

100%

0.4865

：

0.3895

：

INT

60%

Source

X :

0.4260

Y :

0.4005

Tungsten

Incandescent

Halogen

Antique Bulb

Bulb

INT

：

100%

2.2.4) RGB

Press the LIGHT MODE button to enter the light mode interface, rotate the select wheel

and short press to RGB. You can adjust Intensity (0-100%) and Red/Green/Blue values

(0-100%).

2.2.5) XY

Press the LIGHT MODE button to enter the light mode interface, rotate the select wheel

and short press to XY. You can adjust Intensity (0-100%) and X/Y coordinates

(0.0000 – 0.8000).

2.2.6) Source

Press the LIGHT MODE button to enter the light mode interface, rotate the select wheel

and short press to Source. You can choose 46 preset light source eects.

-19-

Connecting DMX to an LS 600c Pro

Daisy chaining multiple lights

using DMX

DMX512

OUTPUT

DMX512

GEL

186

Silver Rose

187

Rouge

188

Peach

189

Peach

189

Peach

DMX2-3

DMX4-5

DMX6-7

DMX8-9

DMX10-11

Col.Corr

Cal.Filter

600 Series

Cosmetic

700 Series

DMX0-1

3200K

5600K

100%

184

Peach

INT

：

100%

CCT

RGB

INT

HUE

SAT

GEL

INT

3200 / L

184

X Y

INT

CCT

G/M

66%

5300K

0.2

80%

60°

255

166

80%

0.3127

0.3290

Adv.

HSI

2.2.7) GEL

Press the LIGHT MODE button to enter the light mode interface, rotate the select wheel

and short press to GEl. You can set 3200K or 5600K as the light color temperature , and

select the Rosco or LEE Gel Lighting Filter paper.

2.3) Light Preset

Press the PRESET button on the control box to enter the light preset mode, you can save

10 light preset eects.

Rotating and short press the select wheel to save/replace the preset eect in CCT, Adv.

HSI, RGB, XY, Source, GEL mode. You can open/delete previously saved to the preset

mode in any mode.

3. Connecting to DMX

3.1) Connecting a standard DMX controller

Page is loading ...

Aputure LS 600c Pro User manual

Aputure LS 600c Pro User manual

Aputure LS 600c Pro User manual

Related papers

Other documents