American Dynamics AD614 Series Installation guide

Brand
American Dynamics
Model
AD614 Series
Category
Camera lenses
Type
Installation guide

This manual is also suitable for

American Dynamics AD614 Series is a fixed camera that comes fully assembled and is simple to install with manually positioned pan and tilt, manually set zoom, focus, and iris. The camera is housed inside a DeltaDrone housing and two camera types are available: NTSC (60Hz color) and PAL (50Hz color). It has a 9-pin connector for pigtail connections and a connector P7 for I/O board connections. The camera can be used for video surveillance and can be attached to a hand-held camera monitor or connected to a remote monitor for viewing.

American Dynamics AD614 Series is a fixed camera that comes fully assembled and is simple to install with manually positioned pan and tilt, manually set zoom, focus, and iris. The camera is housed inside a DeltaDrone housing and two camera types are available: NTSC (60Hz color) and PAL (50Hz color). It has a 9-pin connector for pigtail connections and a connector P7 for I/O board connections. The camera can be used for video surveillance and can be attached to a hand-held camera monitor or connected to a remote monitor for viewing.

Installation Guide
8000-2684-01, Rev. C (2 pages) CCTV PRODUCTS 1
1 DeltaDrone
™
II
Fixed Camera
AD614 Series
The DeltaDrone fixed camera is housed inside a
DeltaDrone housing. Two camera types are
available:
NTSC (60Hz color) and PAL (50Hz color).
Each camera has manually positioned pan and tilt
(the pan has 370° of travel) and manually set
zoom, focus, and iris. The drone camera comes
fully assembled and is simple to install.
IMPORTANT! Anytime you are using a VM96
video controller, and the SpeedDome Ultra Drone
II camera dome is:
• New: Reset the VM96 to update the
configuration form to a fixed camera.
• A replacement for the SpeedDome Ultra
camera dome: Delete the SpeedDome Ultra
configuration form as explained in the VM96
Administrator’s Manual 8000-0756-05. Then
reset the VM96 to update the configuration
form to a fixed camera.
Procedure
The following steps refer to figures opposite:
1. Attach camera dome to base containing a
pigtail connector or I/O board.
a. Align recessed dimple on cap of dome with
red dot on base (pigtail) or logo visible on
I/O board.
b. Mate housing and eyeball assembly to base
and turn it clockwise until you hear a click.
Notes:
This is a fixed camera, no data lines are required.
If connecting to a pigtail base, an LED at top of
dome housing indicates 12V power. This LED
cannot be seen after connection to the I/O board.
2. As shown on page 2, turn eyeball if necessary
to access slot cover containing lens. Unsnap
this cover by gently tugging it away from
eyeball.
3. You now have access to the camera set screw.
To access lens adjustments, loosen set screw
and gently pull camera out until screw reaches
front end of slot. Retighten set screw.
1a
L
A
T
C
H
1b
Pigtail Connections (9-pin connector)
Pin Color Designation
1–2 N/A Not used.
3 Black 24Vac
4 Red Ground
5 White 24vac
6–9 N/A Not used.
I/O Board Connections (connector P7)
Pin Color Designation
1 Black 24Vac
2 Red Ground
3 White 24vac
Power
LED
2 INSTALLATION GUIDE
DELTADRONE FIXED CAMER
A
8000-2684-01, REV.
C
4. Adjust camera as follows:
a. Attach a hand-held camera monitor to video
cable entering mounting base, or have a
second person view the remote monitor
while you adjust the camera.
b. Adjust pan and tilt to point camera at target,
then adjust zoom, focus, and iris as desired.
c. Do not adjust the back focus ring on lens.
d. Combine zoom and focus ring adjustments
to achieve the desired view.
5. Loosen set screw and push camera in until
screw contacts rear end of slot. Retighten set
screw.
6. Ensuring that tongue and grooves of slot cover
already attached to dome are centered over
tabs of the yoke, reattach lens slot cover by
mating tongue and grooves together and gently
pressing until you feel a snap.
WARNING: The tongue and grooves must be
centered over tabs of yoke. Failure to properly
insert cover could result in it falling off during
operation. Tug on cover to ensure it is secure.
2
3
4
Focus
Zoom
Iris
5
Tongue
Groove
Tabs
Yoke
6
  • Page 1 1
  • Page 2 2

American Dynamics AD614 Series Installation guide

Brand
American Dynamics
Model
AD614 Series
Category
Camera lenses
Type
Installation guide
This manual is also suitable for

American Dynamics AD614 Series is a fixed camera that comes fully assembled and is simple to install with manually positioned pan and tilt, manually set zoom, focus, and iris. The camera is housed inside a DeltaDrone housing and two camera types are available: NTSC (60Hz color) and PAL (50Hz color). It has a 9-pin connector for pigtail connections and a connector P7 for I/O board connections. The camera can be used for video surveillance and can be attached to a hand-held camera monitor or connected to a remote monitor for viewing.

Download PDF
report

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI

Related papers