American Dynamics SpeedDome Ultra Drone II Installation guide

Brand
American Dynamics
Model
SpeedDome Ultra Drone II
Type
Installation guide

This manual is also suitable for

American Dynamics SpeedDome Ultra Drone II is a fixed camera that offers a wide range of features for various security and surveillance applications. It comes fully assembled and is easy to install. Here are some of the key capabilities and potential use cases of this device:

Manually Adjustable Pan, Tilt, Zoom, Focus, and Iris:

  • Allows for precise positioning and framing of the camera's view, enabling it to capture footage from different angles and distances.

370° Pan Travel:

  • Provides extensive coverage, making it suitable for monitoring large areas or multiple points of interest.

American Dynamics SpeedDome Ultra Drone II is a fixed camera that offers a wide range of features for various security and surveillance applications. It comes fully assembled and is easy to install. Here are some of the key capabilities and potential use cases of this device:

Manually Adjustable Pan, Tilt, Zoom, Focus, and Iris:

  • Allows for precise positioning and framing of the camera's view, enabling it to capture footage from different angles and distances.

370° Pan Travel:

  • Provides extensive coverage, making it suitable for monitoring large areas or multiple points of interest.
Installation Guide
SPEEDDOME ULTRA DRONE II FIXED CAMERA 8000-2682-01, REV D
INSTALLATION GUIDE 1 of 2
SpeedDome
®
Ultra
Drone
™
II Fixed Camera
RAS614 Series
The SpeedDome Ultra Drone II fixed camera is
housed inside a SpeedDome Ultra dome. Two
camera types are available:
NTSC (60Hz color) and
PAL (50Hz color). Each camera has manually
positioned pan and tilt (the pan has 370° of travel)
and manually set zoom, focus, and iris. The drone
comes fully assembled and is simple to install.
IMPORTANT! Anytime you are using a VM96 video
controller, and the SpeedDome Ultra Drone II
camera dome is:
• New: Reset the VM96 to update the
configuration form to a fixed camera.
• A replacement for the SpeedDome Ultra
camera dome: Delete the SpeedDome Ultra
configuration form as explained in the VM96
Administrator’s Manual 8000-0756-05. Then
reset the VM96 to update the configuration
form to a fixed camera.
Procedure
The following steps refer to figures opposite:
1. Attach the camera dome to the base containing
a pigtail connector or an I/O board.
a. Connect the housing and eyeball assembly
to the base by aligning the Cap and Base
tabs.
b. Turn the eyeball assembly clockwise until
you hear a click.
Notes:
This is a fixed camera, no data lines are
required.
If connecting to a pigtail base, an LED at top
of dome housing indicates 12V power. This
LED cannot be seen after connection to the
I/O board.
2. As shown on page 2, turn eyeball if necessary
to access slot cover containing lens. Unsnap
this cover by gently tugging it away from the
eyeball.
3. You now have access to the camera set screw.
To access lens adjustments, loosen set screw
and gently pull camera out until screw reaches
front end of slot. Retighten set screw.
© 2005 Sensormatic Electronics Corp.
1a
Pigtail Connections (9-pin connector)
Pin Color Designation
1–2 N/A Not used.
3 Black 24Vac
4 Red Ground
5 White 24vac
6–9 N/A Not used.
I/O Board Connections (connector P7)
Pin Color Designation
1 Black 24Vac
2 Red Ground
3 White 24vac
Powe
r
LED
1b
Align tabs on
Cap and Base.
Turn clockwise
to latch
SPEEDDOME ULTRA DRONE II FIXED CAMERA 8000-2682-01, REV D
INSTALLATION GUIDE 2 of 2
4. Adjust camera as follows:
a. Attach a hand-held camera monitor to video
cable entering mounting base, or have a
second person view the remote monitor
while you adjust the camera.
b. Adjust pan and tilt to point camera at target,
then adjust zoom, focus, and iris as desired.
c. Do not adjust the back focus ring on lens.
d. Combine zoom and focus ring adjustments
to achieve the desired view.
5. Loosen set screw and push camera in until
screw contacts rear end of slot. Retighten set
screw.
6. Ensuring that tongue and grooves of slot cover
already attached to dome are centered over
tabs of the yoke, reattach lens slot cover by
mating tongue and grooves together and gently
pressing until you feel a snap.
CAUTION: The tongue and grooves must be
centered over tabs of yoke. Failure to properly
insert cover could result in it falling off during
operation. Tug on cover to ensure it is secure.
2
3
4
Focus
Zoom
Iris
5
Tongue
Groove
Tabs
Yoke
6
  • Page 1 1
  • Page 2 2

American Dynamics SpeedDome Ultra Drone II Installation guide

Brand
American Dynamics
Model
SpeedDome Ultra Drone II
Type
Installation guide
This manual is also suitable for

American Dynamics SpeedDome Ultra Drone II is a fixed camera that offers a wide range of features for various security and surveillance applications. It comes fully assembled and is easy to install. Here are some of the key capabilities and potential use cases of this device:

Manually Adjustable Pan, Tilt, Zoom, Focus, and Iris:

  • Allows for precise positioning and framing of the camera's view, enabling it to capture footage from different angles and distances.

370° Pan Travel:

  • Provides extensive coverage, making it suitable for monitoring large areas or multiple points of interest.
Download PDF
report

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI

Related papers

Other documents