Page is loading ...
DVD-VCR
Kombigerät DVD-Player / Videorecorder
Magnétoscope Lecteur DVD
DVD-VCR
DVD/Video
SV-DVD540
PAL
EJECT
AUX
OPEN/CLOSE
STANDBY/ON
OK
Instruction Manual
Bedienungsanleitung
Mode d’emploi
Istruzioni per l’uso
Gebruiksaanwijzing
F
I
NL
D
GB
www.samsungvcr.com
Deutsche Homepage: www.samsung.de
www.samsung.fr
PAL
00259A SV-DVD540/XEB-GB1 10/15/03 5:04 PM Page 1
2 3
GB GB
Contents
◆ RECORDING TELEVISION BROADCASTS
■ Selecting the Recording Speed................................................................................................ 27
■ Protecting a Recorded Cassette .............................................................................................. 28
■ Recording a Programme Immediately...................................................................................... 28
■ Recording a Programme with Automatic Stop ......................................................................... 29
■ Using the ShowView Feature................................................................................................... 30
■ Modifying ShowView Programming ......................................................................................... 31
■ Using the Timer Programming Feature.................................................................................... 32
■ Checking a Preset Recording .................................................................................................. 33
■ Cancelling a Preset Recording................................................................................................ 33
◆ PLAYING BACK
■ Playing a Cassette ................................................................................................................... 34
■ Adjusting Picture Alignment Manually...................................................................................... 34
■ Selecting the Audio Output Mode ............................................................................................ 35
■ Playing a Cassette in Slow Motion........................................................................................... 35
■ Playing a Sequence Frame by Frame...................................................................................... 36
■ Playing a Sequence at Variable Speeds.................................................................................. 36
■ Searching for a Specific Sequence .......................................................................................... 37
■ Using the Tape Counter ........................................................................................................... 39
■ Connecting an RCA Audio/Video Input Cable.......................................................................... 40
■ Using the Assemble Edit Function ........................................................................................... 41
■ Recording from Another VCR or Camcorder ........................................................................... 41
◆ DVD FUNCTIONS
■ Using the TV Buttons on the Remote Control .......................................................................... 42
■ Choosing a Connection............................................................................................................ 43
■
Setting Up the Language Features
................................................................................................ 44
■
Setting Up the Audio Options
........................................................................................................ 46
■
Setting Up the Display Options
..................................................................................................... 47
■
Setting Up the Parental Control
.................................................................................................... 48
■
A/V Receiver Connections
........................................................................................................... 49
■
Special Playback Features
........................................................................................................... 50
■
Adjusting the Aspect Ratio (EZ View)
............................................................................................ 51
■
Using the Display Function
........................................................................................................... 53
■
Changing the Camera Angle
........................................................................................................ 54
■
Selecting the Subtitle Language
.................................................................................................... 54
■
Repeat Play
................................................................................................................................55
■
Selecting the Audio Language
...................................................................................................... 56
■
Using the Mark Function
.............................................................................................................. 57
■
MP3/WMA Play
........................................................................................................................... 59
■
Program Play & Random Play
...................................................................................................... 60
■
Picture CD Playback
.................................................................................................................... 61
Contents
◆ FOREWORD
■ Safety Instructions................................................................................................................ 5
■ Disc Type and Characteristics ............................................................................................. 6
◆ DVD-VCR OVERVIEWS
■ Front View of the DVD-VCR................................................................................................. 7
■ Rear View of the DVD-VCR ................................................................................................. 7
■ Infrared Remote Control....................................................................................................... 8
■ Display Indicators................................................................................................................. 9
■ Accessories.......................................................................................................................... 9
◆ CONNECTING YOUR DVD-VCR
■ Deciding How to Connect DVD-VCR ................................................................................... 10
■ Connecting DVD-VCR to the TV using the Coaxial Cable ................................................... 11
■ Connecting DVD-VCR to the TV using the SCART Cable................................................... 11
■ Connecting DVD-VCR to a Satellite Receiver or Other Equipment ..................................... 12
■ Plug & Auto Set Up .............................................................................................................. 13
■ Deck Control Keys ...............................................................................................................14
■ Basic TV Tuner Operations.................................................................................................. 15
■ Inserting Batteries in the Remote Control ............................................................................ 16
■ Setting the Date and Time ................................................................................................... 16
■ Menu Language ...................................................................................................................17
◆ SETTING UP YOUR DVD-VCR
■ Presetting the Stations Automatically................................................................................... 18
■ Presetting the Stations Manually.......................................................................................... 19
■ Clearing a Preset Station ..................................................................................................... 20
■ Changing the Preset Station Table ...................................................................................... 21
■ Selecting the Colour Mode................................................................................................... 22
■ NICAM.................................................................................................................................. 22
■ Intelligent Picture Control .....................................................................................................23
■ Intelligent Picture Control (Remote Control) ........................................................................ 23
■ ShowView Extend ................................................................................................................ 24
■ Auto Power off...................................................................................................................... 25
■ Screen Messages ................................................................................................................ 25
■ Selecting the Cassette Type ................................................................................................ 26
■ Repeat Play.......................................................................................................................... 26
■ S-VHS Play .......................................................................................................................... 27
00259A SV-DVD540/XEB-GB1 10/15/03 5:04 PM Page 2
Safety Instructions
4 5
GB GB
Contents (cont.)
◆ SOLVING PROBLEMS
■ Technical Specifications ...................................................................................................... 63
■ Problems and Solutions (VCR)............................................................................................ 64
■ Troubleshooting Guide (DVD) ............................................................................................. 65
Symbols
1 1
☛
➢
Press/push
Hold down
= Step number
Important Note
1
The lightning bolt is a warning sign alerting you to dangerous voltage inside the product.
DO NOT OPEN THE DVD-VCR. Refer to service personnel.
HH
5°C
40°C
10% 75%
THIS DEVICE IS NOT FOR USE IN INDUSTRIAL
ENVIRONMENTS
Do NOT expose the DVD-VCR
to extreme temperature condi-
tions (below 5°C and above
40°C) or to extreme humidity
conditions (less than 10% and
more than 75%).
Do NOT expose the DVD-VCR
to direct sunlight.
Do NOT expose the DVD-VCR
to any liquids.
Do NOT place any objects on
the DVD-VCR or remote
control.
During a storm and/or light-
ning, unplug the DVD-VCR
from the mains socket and
aerial.
If the remote control is not
used for a long period of time,
remove the batteries and store
it in a cool, dry place.
The following illustrations represent precautions.
This manuel is divided into two sections:
one describing the VCR; the other, the DVD.
Prior to undertaking anything, please verify in which section you actually are by
checking either the or symbols or the header of the chapter.
DVDVCR
This product incorporates copyright protection technology that is protected by
method claims of certain U.S. patents and other intellectual property rights owned by
Macrovision Corporation and other rights owners. Use of this copyright protection
technology must by authorized by Macrovision Corporized by Macrovision
Corporation, and is intended for home and other limited viewing uses only unless
otherwise authorized by Macrovision Corporation. Reverse engineering or
disassembly is prohibited.
00259A SV-DVD540/XEB-GB1 10/15/03 5:04 PM Page 4
6 7
GB GB
Disc Type and Characteristics
This DVD player is capable of playing the following types of discs with the corresponding logos :
* DO NOT play CD-ROM, CD-I and DVD-ROM in this player!
(CDGs play audio only, not graphics.)
* It may not be to play CD-R,CD-RW and DVD-R in all cases due to the type of disc or condition of the recording.
~
DIGITAL
SOUND
STEREO
• Playback
Region
Number
• PAL colour
system in U.K,
France, Germany,
etc.
• Dolby
Digital disc
• Digital
Audio disc
• Stereo
disc
• DTS disc
Disc Markings
Both the DVD player and the discs are coded by region. These regional codes must match in order for the
disc to play. If the codes do not match, the disc will not play.
The Region Number for this player is described on the rear panel of the player.
Playback Region Number
PAL
12 Cm
8 Cm
Single-sided
240 min.
Double-sided
480 min.
Single-sided
80 min.
Double-sided
160 min.
Audio
+
Video
Audio
• DVD contains excellent sound
and video due to Dolby Digital
and MPEG-2 system.
• Various screen and audio
functions can be easily selected
through the on-screen menu.
• An LP is recorded as an analog
signal with more distortion. CD
is recorded as a Digital Signal
with better audio quality, less
distortion and less deterioration
of audio quality over time.
AUDIO-CD
12 Cm
8 Cm
74 min.
20 min.
Disc Types
(Logos)
Recording
Types
Disc Size
Max.
Playing
Time
Characteristics
DVD
• NTSC broadcast
system in USA,
Canada, japan,
South Korea, etc.
NTSC
Front View of the DVD-VCR
EJECT
AUX
VIDEO CASSETTE COMPARTMENT
AUX VIDEO INPUT JACK
PLAY/STILL BUTTON
EZ VIEW BUTTON
STOP BUTTON
REW /SKIP BACK
BUTTON
RECORD
BUTTON
EJECT BUTTON
F.F / SKIP NEXT BUTTON
PROGRAMME SELECTION
BUTTON
OPEN/CLOSE
BUTTON
VCR SELECT BUTTON
DVD SELECT BUTTON
DVD DECK
STANDBY/ON BUTTON
AUX AUDIO L, R INPUT JACK
Rear View of the DVD-VCR
COAXIAL
DIGITAL AUDIO OUT
LINE OUT
OPTICAL
S-VIDEO OUT
L
R
AUDIO
AERIAL IN
CONNECTOR
OUT TO TV CONNECTOR
AV2 (DEC./EXT.) SCART
(EURO-21) SOCKET
AV1 (EURO AV) IN/OUT SCART
(EURO-21) SOCKET
AUDIO L, R OUT SOCKETS
AUDIO L, R OUT SOCKETS
(DVD ONLY)
DIGITAL AUDIO OUT SOCKET
(COAXIAL)
VIDEO OUT SOCKET
S-VIDEO OUT JACK
DIGITAL AUDIO OUT SOCKET
(OPTICAL)
00259A SV-DVD540/XEB-GB1 10/15/03 5:04 PM Page 6
Display Indicators
Accessories
You have just purchased a SAMSUNG Video Cassette Recorder (DVD-VCR).
Together with your DVD-VCR, you will find the following accessories in the box.
O
P
E
N
/
C
L
O
S
E
S
T
A
N
D
B
Y
/
O
N
REMOTE CONTROL
& BATTERIES
AUDIO & VIDEO
CABLE
OWNER’S
INSTRUCTIONS
COAXIAL CABLE
STEREO
1 2 3 4 5
6 7 8
1 The DVD Deck is active
2 A DVD, CD or SVCD is loaded
3 The time, counter position, time remaining or
current deck status is displayed
4 VHS tape is inserted
5 The VCR Deck is active
6 A DVD with a DTS soundtrack is loaded
7 The Hi-Fi track of a VHS tape is playing
(The current TV show or video is broadcast in
Stereo)
8 A Timer Recording is programmed or in progress.
8 9
GB GB
Infrared Remote Control
1 STANDBY/ON
2 SHUTTLE << / >>
3 CLEAR
4 DVD
5 TV MUTE. AUDIO
6 VOLUME +/–
7 REWIND
SKIP BACK
8 STOP
9 SUBTITLE
10 MENU
11 UP
12 LEFT
13 DOWN
14 SPEED
15 RECORD
16 TIMER
17 ANGLE
IPC
18 OPEN/CLOSE
19 0-9
20 TV/VCR
21 VCR, TV SELECT
22 INPUT SEL.
F.ADV/STEP
23 PROG
TRACKING
24 FAST-FORWARD
SKIP NEXT
25 PLAY/STILL
26 INFO.
27 RETURN
28 RIGHT
29 OK
30 EZ VIEW
31 DISC MENU
32 MARK
SEARCH
33 MODE
REPEAT
OPEN/CLOSE
STANDBY/ON
OK
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
00259A SV-DVD540/XEB-GB1 10/15/03 5:04 PM Page 8
10 11
GB GB
LINE O
Connecting DVD-VCR to the TV using the Coaxial Cable
Connecting DVD-VCR to the TV using the SCART Cable
To receive television programmes a signal must be received from
one of the following sources:
◆ An outdoor aerial
◆ An indoor aerial
◆ A cable television network
◆ A satellite receiver
☛ Make sure that both the television and the DVD-VCR
are switched off
before connecting the cables.
1 Remove the aerial or network input cable from the television.
2 Connect this cable to the 75Ω coaxial socket marked on
the rear of your DVD-VCR.
3 Plug the coaxial cable supplied into the socket on your
DVD-VCR.
4 Plug the other end of the coaxial cable into the connector
previously used for the aerial on the television.
5 To obtain better quality pictures and sound on your television,
you can also connect your DVD-VCR to the television via the
SCART cable (see section below) if your television is equipped
with this type of connection.
TV
LINE OUT
L
R
3
2
C
O
DI
LINE OUT
L
R
AUDIO
You can connect your DVD-VCR to the television using the SCART cable if the appropriate input is available
on the television. You thus:
◆ Obtain better quality sound and pictures
◆ Simplify the setting up procedure of your DVD-VCR
☛ ◆ Regardless of the type of connection chosen, you must always connect the coaxial cable
supplied. Otherwise, no picture will be visible on the screen when the DVD-VCR is switched
off.
◆ Make sure that both the television and the DVD-VCR are switched off
before connecting the
cables.
1 Connect the coaxial cable as indicated in the above section.
2 Connect one end of the SCART cable to the AV1 (EURO AV) socket on the rear of the DVD-VCR.
3 Plug the other end into the appropriate connector on the television.
Aerial
SCART Cable
RF coaxial cable
2
3
TV
TV
4
Deciding How to Connect DVD-VCR
You must take into account various factors when connecting audio or video systems:
◆ Types of connectors available on your systems
◆ Systems connected permanently to the DVD-VCR (satellite receiver for example) or
temporarily (camcorder for example)
Your DVD-VCR is equipped with the following connectors.
Connector Location Type Direction Recommended Use
AV1 (EURO AV)
Rear SCART In/Out ◆ Television
◆ Satellite receiver
◆ Other VCR
AV2 IN Rear SCART In ◆ Satellite receiver
◆ Other VCR
Audio output Rear Audio RCA Out ◆ Audio out
AUX Front Aux In ◆ Audio in
Audio/Video Video in
VIDEO output Rear RCA Out ◆ Video out
S-VIDEO Rear S-JACK Out ◆ S-Video out (DVD only)
output
Digital AUDIO Rear Optical Out ◆ Digital Audio out (DVD only)
output Coaxial
OUT TO TV Rear 75 Ω Out ◆ Television
coaxial
IN FROM ANT. Rear 75 Ω In ◆ Aerial
coaxial ◆ Cable television network
◆ Satellite receiver
☛ Whenever you connect an audio or video system to your DVD-VCR, ensure that all elements
are switched off
.
Refer to the documentation supplied with your equipment for detailed connection instructions
and associated safety precautions.
S-VIDEO OUT
COAXIAL
OPTICAL
00259A SV-DVD540/XEB-GB1 10/15/03 5:04 PM Page 10
12 13
GB GB
Plug & Auto Set up
Your DVD-VCR will automatically set itself up when it is plugged
into the mains for the first time. TV stations will be stored in
memory. The process takes a few minutes. Your DVD-VCR will
then be ready for use.
1 Connect the coaxial cable as indicated on page 11.
(Connecting Your DVD-VCR to the TV Using the Coaxial Cable)
2 Plug the DVD-VCR into the mains.
Result: The Language Set menu is displayed.
3 Select the required language by pressing the
or
❷
buttons.
4 Press OK to store the language selected.
Result
: A message appears.
5 Press OK button.
6 Press the
or
❷
buttons to select your country.
☛ The VCR searches for the stations according to a preset
preference list corresponding to the country that you have
selected.
7 Press OK to start the auto scanning.
◆ The number of stations automatically stored by the VCR
depends on the number of stations that it has found.
8 The current time and date are displayed automatically.
Check the date and time.
if it is :
◆
Correct, Press RETURN button twice to exit the menu.
◆
incorrect, see page 16.
➢ Auto preset can be performed by pressing
■
(STOP) on
the VCR continuously for 5 seconds or more with no
tape inserted.
Connecting DVD-VCR to a Satellite Receiver or Other Equipment
1. AV2 IN: By means of 21-pin Scart Cable
Plug the SCART Cable with satellite receiver or other equipment into the AV2 (DEC./EXT.) socket on the rear of
the DVD-VCR.
After making this connection, select the source by pressing the INPUT SEL. button for the AV2 input sources.
2. By means of RF Coaxial Cable
After making this connection, you must preset the station received through the satellite tuner.
RF output channel of the satellite receiver should be adjusted away from channel 36, which is used by the
DVD-VCR, e.g. re-adjust to channel 39.
Satellite Receiver or other Equipment
1. AV1(EURO AV): By means of 21-pin Scart Cable
Plug the SCART Cable with satellite receiver or other equipment into the AV1 (EURO AV) socket on the rear of the
DVD-VCR.
After making this connection, select the source by pressing the INPUT SEL. button for the AV1 input sources.
2. By means of RF Coaxial Cable
After making this connection, you must preset the station received through the satellite tuner.
RF output channel of the satellite receiver should be adjusted away from channel 36, which is used by the
DVD-VCR, e.g. re-adjust to channel 39.
Aerial
Aerial Connector
SCART Cable
RF coaxial cable
1
2
TV
Satellite Receiver or other Equipment
Aerial
Aerial Connector
SCART Cable
RF coaxial cable
1
2
TV
You can connect your DVD-VCR to a Satellite receiver or other DVD-VCR using the SCART cable if the
appropriate outputs are available on the equipment chosen. The following illustrations give a few
examples of the connection possibilities.
2
LINE OUT
L
R
TV
Auto setup
Please wait
00 %
Clock Set
Auto Clock : On
Time Date Year
12 : 00 1 / JAN / 2003 WED
00259A SV-DVD540/XEB-GB1 10/15/03 5:04 PM Page 12
15
GB
14
GB
Basic TV Tuner Operations
The following buttons are used when watching television via the
DVD-VCR’s built-in TV tuner.
1 TV/VCR Button
Press to switch between your TV’s tuner and the VCR’s internal
tuner.
2 PROG Button
Press to change to the next or previous channel.
3 0-9 Buttons
Press to select channels directly.
4 INFO.
Press to display the channel you are watching.
◆ Also works in DVD and VCR mode.
1
2
2
3
OK
4
Deck Control Keys
The DVD-VCR uses one set of controls to operate both decks.
The following keys are helpful in successfully controlling each
deck.
1 STANDBY/ON Button
Press the STANDBY/ON button on the remote control or front
panel to turn on the DVD-VCR.
2 DVD Button
Press the DVD button on the remote control when you want to
control the DVD deck.
◆ The DVD indicator will light on the Front Panel Display to
show that the DVD deck is selected.
3 VCR Button
Press the VCR button on remote control when you want to
control the VCR deck.
◆ The VCR indicator will light on the Front Panel Display to
show that VHS deck is selected.
4 INPUT SEL. BUTTON
Press the INPUT SEL. button repeatedly to cycle through all of
your input sources, including the Tuner (PR##), AV1 (rear AV
input), AV2 (rear AV input), AUX (front AV input).
• It is only available when VCR deck is selected.
➢ Before using the VCR operation of 18~42 pages, press
the VCR button on the remote control to select VCR
mode.
Before using the DVD operation of 43~62 pages, press
the DVD button on the remote control to select and
watch DVD.
1
STANDBY/ON
1
2
3
4
00259A SV-DVD540/XEB-GB1 10/15/03 5:04 PM Page 14
17
GB
16
GB
Setting the Menu Language
1 Open “MENU”
After pressing the MENU, press the OK or
❿ .
2 Select “Language”
Use the
or
❷
buttons to highlight
“Language,” then press the OK or
❿ .
3 Set menu Language
Place the selection arrow next to your desired Language, then
press the OK button.
4 Press the
or
❷
buttons to select language you want.
Place the selection arrow next to your desired Language, then
press the OK button.
5 On completion, press RETURN to exit the menu.
Language : English
User Set
Auto Power Off : Off
Screen Messages : On
Install
Français
Deutsch
Español
Italiano
Nederlands
Language Set
English
OK
1
Inserting Batteries in the Remote Control
Setting the Date and Time
You must insert or replace the batteries in the remote control
when you:
◆ Purchase the DVD-VCR
◆ Find that the remote control is no longer working
correctly
1 Push the tab in the direction of the arrow to release the battery
compartment cover on the rear of the remote control.
2 Insert two AAA, RO3 or equivalent batteries, taking care to
respect the polarities:
◆ + on the battery with + on the remote control
◆ – on the battery with – on the remote control
3 Replace the cover by aligning it with the base of the remote
control and pushing it back into place.
➢ Do not mix different battery types (manganese and
alkaline for example).
Your DVD-VCR contains a 24-hour clock and calendar used to:
◆ Automatically stop programme recording
◆ Preset your DVD-VCR to record a programme
automatically
You must set the date and time when:
◆ You purchase the DVD-VCR
☛
◆ The time and date are set automatically from the
broadcast signal. If the signal is weak or ghosting
occurs, the time and date may not be set automati-
cally. In this case, they should be set manually.
◆ Do not forget to reset the time when you change
clocks from winter to summer time and vice versa.
1 After pressing the MENU, press the OK or
❿ .
Result: The Setup menu is displayed.
2 Press the corresponding
,
❷
buttons to select the Clock
option.
3 Press the OK or
❿
to select this option.
Result
: The Clock Set menu is displayed.
4 Press
➛
or
❿
to select the hour, minutes, day, month and year.
Result
: The option selected highlight.
5 Press the
or
❷
buttons to increase or decrease the value.
Result
: The day of the week is displayed automatically.
➢ You can hold the
or
❷
buttons down to scroll more
quickly through the values.
6 On completion, press RETURN to exit the menu.
Time Date Year
Clock Set
12 : 00 1 / JAN / 2003 WED
Auto Clock : On
1
Language : English
User Set
Auto Power Off : Off
Screen Messages : On
Install
00259A SV-DVD540/XEB-GB1 10/15/03 5:04 PM Page 16
18
GB
Presetting the Stations Automatically
☛
You do not need to preset the stations if you have already
set them automatically (see Plug & Auto Set Up on page 13).
Your DVD-VCR contains a built-in tuner used to receive television
broadcasts.
You must preset the stations received through the tuner. This can
be done:
◆ Plug & Auto Set up (see page 13)
◆ Automatically
◆ Manually (see page 19)
You can store up to 80 stations.
1 After pressing the MENU, press the OK or
❿ .
Result: The Setup menu is displayed.
2 Press the corresponding
,
❷
buttons to select the Install
option.
3 Press the OK or
❿
to select this option.
Result
:The Install menu is displayed.
4 Press the corresponding
or
❷
buttons, until the Auto
Setup is selected.
And then press the OK or
❿
to select this option.
Result
: A message appears, indicating that any channels
already preset on your DVD-VCR will be deleted.
5 Press the
or
❷
buttons to select your country.
☛ The VCR searches for the stations according to a preset
preference list corresponding to the country that you have
selected.
6 Press OK button.
Result
: A message appears, indicating that any channels
already preset on your VCR will be deleted.
7 Press OK to start the auto scanning.
Result
: ◆ The Please Wait indication highlight on the
television screen.
◆ The first frequency band is scanned and the first
station found is displayed and stored.
◆ The DVD-VCR then searches for the second station
and so on.
◆ When the automatic scanning procedure has
finished, the DVD-VCR switches automatically to
programme 1.
➢ The number of stations automatically stored by the DVD-
VCR depends on the number of stations that it has found.
8 If you wish to cancel the auto scanning before the end, press the
MENU button to exit the menu.
➢ ◆ The time and date are set automatically from the
broadcast signal. If the signal is weak or ghosting
occurs, the time and date may not be set automati-
cally. In this case, they should be set manually (see
page 16).
◆ Once the auto scanning procedure has finished, some
stations may have been stored more than once; select
the stations with the best reception and delete the
ones no longer required (see page 20).
Auto Setup
Your date will be lost
Press OK to continue
Menu to exit
Auto Setup
Manual Setup
Install
COUNTRY SELECTION
A NL S PL
B I CH CZ
DK
N TR OTHERS
FIN P GR
D E HU
Language : English
User Set
Auto Power Off : Off
Screen Messages : On
Install
Auto Setup
Please Wait
15%
VCR
00259A SV-DVD540/XEB-GB1 10/15/03 5:04 PM Page 18
19
GB
☛ You do not need to preset the stations manually if you
have already set them automatically.
1 After pressing the MENU, press the OK or
❿ .
Result: The Setup menu is displayed.
2 Press the corresponding
,
❷
buttons to select the Install
option.
3 Press the OK or
❿
to select this option.
Result
: The Install menu is displayed.
4 Press the corresponding
or
❷
buttons, until the Manual
Setup option is selected.
5 Press the OK or
❿
to select a Manual Setup option.
Result
: The TV STATION TABLE menu is displayed.
6 Press the
or
❷
buttons to select a programme number as
required.
7 Press the
❿
button to preset the station.
Result
: The MANUAL TUNING menu is displayed.
8 Press the
➛
or
❿
buttons to start scanning channel.
Result
: The frequency band is scanned and the first station
found is displayed.
9 Press the
❷
button, until the DECODER is selected.
10 Press the
❿
button to activate or deactivate use of the decoder
for the TV station, if necessary.
11 Press the
or
❷
buttons until the NAME is selected.
The station name is set automatically from the broadcast signal.
12 To change the programme’s name, press the
❿
button.
Result
: The first letter of the name flashes.
13 To... Then...
Select a character Press the
or
❷
button until the
in the name required character is displayed
(letters, numbers or “-” character).
Move to the next or Press the
❿
or
➛
buttons
previous character respectively.
14 If you... Then...
Wish to store the ◆ Press the
or
❷
buttons until the MFT
station displayed is selected.
◆ Press the
➛
or
❿
buttons to adjust the
picture, if necessary.
◆ Press OK to store the station
Do not wish to ◆ Press the
or
❷
buttons until the CH
store the station is selected.
displayed
◆ Press the
➛
or
❿
buttons to go on
scanning the frequency band and display
the next station
◆ Go back to the beginning of Step 14
15 Repeat this procedure from Step 6 onwards, until all the required
stations have been stored.
16 On completion, press the RETURN button three times to exit the
menu.
Presetting the Stations Manually
Auto Setup
Manual Setup
Install
Language : English
User Set
Auto Power Off : Off
Screen Messages : On
Install
MANUAL TUNING
SYSTEM :
PR :
CH : - - -
MFT : -
DECODER : OFF
NAME : - - - -
MEMORY : OK
RETURN
TV STATION TABLE
PR CH NAME DEC SYSTEM
1
2
3
4
5
SWAPPING : OK
DELETE : CLEAR RETURN
VCR
00259A SV-DVD540/XEB-GB2 10/15/03 5:03 PM Page 19
21
GB
20
GB
Changing the Preset Station Table
You can rearrange the Station Table and give different
programme numbers to the stations listed according to your own
preferences.
1 After pressing the MENU, press the OK or
❿ .
Result: The Setup menu is displayed.
2 Press the corresponding
,
❷
buttons to select the Install
option.
3 Press the OK or
❿
buttons to select this option.
Result
: The Install menu is displayed.
4 Press the corresponding
or
❷
buttons, until the Manual
Setup option is selected.
5 Press the OK or
❿
button to select this option.
Result
: The TV STATION TABLE menu is displayed.
6 Press the corresponding
or
❷
buttons, until the required
preset TV programme is selected.
Result
: The selected station is displayed at the same time on
the television screen.
7 To change the programme number assigned to a station press
the OK button on the remote control. (For example, To move a
TV station in programme 1 to programme 3)
8 Press the
or
❷
buttons to select required position.
And then press OK again to swap the position.
9 On completion, press the RETURN button four times to exit the
menu.
VCR
Language : English
User Set
Auto Power Off : Off
Screen Messages : On
Install
Auto Setup
Manual Setup
Install
PR CH NAME DEC SYSTEM
1 21
2
3
4
5
- - - -
TV STATION TABLE
SWAPPING : OK
DELETE : CLEAR RETURN
PR CH NAME DEC SYSTEM
1
2
3 21
4
5
- - - -
TV STATION TABLE
SWAPPING : OK
DELETE : CLEAR RETURN
Clearing a Preset Station
If you have stored a TV station:
◆ That you do not require
◆ At the wrong programme position
you can cancel it.
1 After pressing the MENU, press the OK or
❿ .
Result: The Setup menu is displayed.
2 Press the corresponding
,
❷
buttons to select the Install
option.
3 Press the OK or
❿
to select this option.
Result
: The Install menu is displayed.
4 Press the corresponding
or
❷
buttons, until the Manual
Setup option is selected.
5 Press the OK or
❿
to select a Manual Setup option.
Result
: The TV STATION TABLE menu is displayed.
6 Press the corresponding
or
❷
buttons, until the required
preset TV station (PR) is selected.
7 Press the CLEAR button.
8 Repeat the same procedure from Step 6 onwards until all the
required stations have been cleared.
9 On completion, press the RETURN button four times to exit the
menu.
VCR
Language : English
User Set
Auto Power Off : Off
Screen Messages : On
Install
Auto Setup
Manual Setup
Install
PR CH NAME DEC SYSTEM
1 21
2
3
4
5
TV STATION TABLE
SWAPPING : OK
DELETE : CLEAR RETURN
00259A SV-DVD540/XEB-GB2 10/15/03 5:03 PM Page 20
23
GB
22
GB
Intelligent Picture Control
Intelligent Picture Control ( Remote Control )
VCR
VCR
The Intelligent Picture Control Feature allows you to adjust the
sharpness of the image automatically, according to your own
preferences.
1 During playback, press the MENU button on the remote control.
Result
: The Setup menu is displayed.
2 Press the OK or
❿ .
Result: The Setup menu is displayed.
3 Press the corresponding
,
❷
buttons to select the
User Set option.
4 Press the OK or
❿
buttons to select this option.
Result
: The User Set menu is displayed.
5 Press the corresponding
or
❷
buttons, until the IPC option is
selected.
6 Press the Ok or
❿
buttons to select the IPC (intelligent picture
control) option.
➢ When intelligent picture control mode is On, the
sharpness
of the image is adjusted automatically.
7 To adjust the sharpness manually, press the
❷
button to turn
the IPC mode
Off
.
8 Press the
➛
or
❿
buttons until the picture is displayed according
to your preferences.
➢ If you do not press a button within ten seconds, the
PICTURE menu disappears automatically.
9 On completion, press the RETURN button again.
Colour System : Auto
NICAM : On
IPC : On
ShowView Extend : Off
User Set
Language : English
User Set
Auto Power Off : Off
Screen Messages : On
Install
On
Off
1 During playback, press the IPC button.
Result: The PICTURE menu is displayed.
2 Press the
❷
button to turn the IPC (Intelligent Picture Control)
option
On and Off.
➢ When Intelligent Picture Control mode is On, the
sharpness of the image is adjusted automatically.
3 To adjust the sharpness manually, select Intelligent Picture
Control mode
Off.
◆ The horizontal picture adjusting appears.
4 Press the
➛
or
❿
buttons until the picture is displayed according
to your preferences.
➢ If you do not press a button within ten seconds, the
PICTURE menu disappears automatically.
5 On completion, press the IPC button again.
OK
5
NICAM
Selecting the Colour Mode
VCR
VCR
Before recording or playing back a cassette, you can select the
required system standard.
Otherwise, the system automatically selects the reception
standard when you select AUTO.
➢
◆ When playing back a cassette, the standard is
automatically selected by the DVD-VCR.
◆ When you playback an NTSC-recorded tape on this DVD-
VCR make a setting on the colour system according to
your TV. If your TV is a PAL system only TV, set NTPB.
If your TV is Multi System TV (NTSC 4.43 compatible), set
NT4.43 and you can record NT4.43.
1 After pressing the MENU, press the OK or
❿ .
Result: The Setup menu is displayed.
2 Press the corresponding
,
❷
buttons to select the
User Set option.
3 Press the OK or
❿
to select this option.
Result
:The User Set menu is displayed.
4 Press the corresponding
or
❷
buttons, until the Colour
System option is selected.
5 Press the OK or
❿
button to select Auto
➝
PAL
➝
SECAM
➝
MESECAM
➝
B/W.
Auto When playing back a cassette, the system standard is
automatically selected by the DVD-VCR.
B/W Black and White
6 On completion, press RETURN three time to exit the menu.
Language : English
User Set
Auto Power Off : Off
Screen Messages : On
Install
Colour System : Auto
NICAM : On
IPC : On
ShowView Extend : Off
User Set
NICAM programmes are divided into 3 types. NICAM Stereo,
NICAM Mono and Bilingual (transmission in another language).
NICAM programmes are always accompanied by a standard
mono sound broadcast and you can select the desired sound.
Please refer to page 35.
1 After pressing the MENU, press the OK or
❿ .
Result: The Setup menu is displayed.
2 Press the corresponding
,
❷
buttons to select the
User Set option.
3 Press the OK or
❿
to select this option.
Result
: The User Set menu is displayed.
4 Press the corresponding
or
❷
buttons, until the NICAM
options selected.
5 To... Press OK or
❿
, until...
Mono mode Off is displayed.
Off: Only set at this position to record
the standard mono sound during a
NICAM broadcast if the stereo sound is
distorted due to inferior reception
conditions.
NICAM mode On is displayed.
On: Normally set at this position.
6 On completion, press RETURN three times to exit the menu.
Language : English
User Set
Auto Power Off : Off
Screen Messages : On
Install
Colour System : Auto
NICAM : On
IPC : On
ShowView Extend : Off
User Set
On
Off
Auto
PAL
SECAM
MESECAM
B/W
00259A SV-DVD540/XEB-GB2 10/15/03 5:03 PM Page 22
25
GB
24
GB
Screen Messages
Your DVD-VCR displays most information both on the DVD-VCR
and the television.
You can choose to display or hide this information on the
television screen (except for the SEARCH, Programming MENU
and
Timer functions, which cannot be hidden).
1 After pressing the MENU, press the OK or
❿ .
Result: The Setup menu is displayed.
2 Press the corresponding
or
❷
buttons, until the Screen
Messages option is selected.
3 To... Press OK or
❿
, until...
Display on-screen information On is displayed.
Hide on-screen information Off is displayed.
4 On completion, press RETURN twice to exit the menu.
Language : English
User Set
Auto Power Off : Off
Install
Screen Messages : On
On
Off
VCR
Auto Power Off
VCR
The Auto Power Off feature automatically turns off your DVD-
VCR if no signal is received and you do not press any button for
the selected time.
1 After pressing the MENU, press the OK or
❿ .
Result: The Setup menu is displayed.
2 Press the corresponding
or
❷
buttons, until the Auto
Power Off option is selected.
3 Press the
OK or
❿
buttons, until you select the time of Auto
Power Off interval.
Off 1Hour 2Hour 3Hour
4 On completion, press RETURN twice to exit the menu.
Language : English
User Set
Screen Messages : On
Install
Auto Power Off : Off
Language : English
User Set
Auto Power Off : Off
Screen Messages : On
Install
Off
1Hour
2Hour
3Hour
To prevent delays or over-runs the VCR has a function called
ShowView EXTEND allowing you to extend the recording time by
up to 60 minutes.
➢ Only use if PDC is not available or set to Off.
1 After pressing the MENU, press the OK or
❿ .
2 Press the corresponding
,
❷
buttons to select the User Set
option.
3 Press the OK or
❿
buttons to select this option.
Result
: The User Set menu is displayed.
4 Press the corresponding
or
❷
buttons, until the
ShowView Extend option is selected.
5 Press the OK or
❿
buttons to set the ShowView Extend time
by increments of 10 minutes.
6 To turn off, press OK or
❿
buttons repeatedly until Off shows.
Colour System : Auto
NICAM : On
IPC : On
ShowView Extend : Off
User Set
Language : English
User Set
Auto Power Off : Off
Screen Messages : On
Install
Off
10
20
30
40
50
60
ShowView Extend
VCR
00259A SV-DVD540/XEB-GB2 10/15/03 5:03 PM Page 24
27
GB
26
GB
Selecting the Recording Speed
VCR
You can record a cassette at two different speeds:
◆ SP (Standard Play)
◆ LP (Long Play)
In Long Play modes:
◆ Each cassette lasts twice as long
◆ The recording is of a slightly lower quality
To record a cassette... Press the SPEED button on the
remote control, until...
In standard play mode SP is displayed.
In long play mode
LP is displayed.
T
ype Recording Time (in SP)
E-180 180 mins. or 3 hours
E-240 240 mins. or 4 hours
E-260 260 mins. or
4 hours and 20 mins.
E-300 300 mins. or 5 hours
OK
S-VHS Play
Repeat Play
VCR
VCR
You can set repeat play to repeat the tape continuously from
beginning to end.
1 After pressing the MENU, press the corresponding
,
❷
buttons to select the VCR option.
2 Press the OK or
❿
buttons to select this option.
Result
: The VCR Setup menu is displayed.
3 Press the corresponding
or
❷
buttons, until the Repeat
Play option is selected.
4 To... Press OK or
❿
, until...
Repeat play On is displayed.
Do not wish to repeat play Off is displayed.
5 On completion, press RETURN twice to exit the menu.
Language : English
User Set
Auto Power Off : Off
Screen Messages : On
Install
Tape Select : E180
Repeat Play : Off
S-VHS : Off
VCR Setup
The DVD-VCR allows you to playback high quality S-VHS tapes.
1 During S-VHS play mode after pressing the MENU press the
corresponding
,
❷
buttons to select the VCR option.
2 Press the OK or
❿
buttons to select this option.
Result
: The VCR Setup menu is displayed.
3 Press the corresponding
or
❷
buttons, until the S-VHS
option is selected.
4 To... Press OK or
❿
, until...
S-VHS play On is displayed.
Do not wish to S-VHS play Off is displayed.
5 On completion, press RETURN twice to exit the menu.
To watch S-VHS tapes, set the S-VHS mode to
On in the VCR
Setup.
Off
On
Language : English
User Set
Auto Power Off : Off
Screen Messages : On
Install
Repeat Play : Off
VCR Setup
Tape Select : E180
S-VHS : Off
Off
On
Selecting the Cassette Type
Language : English
User Set
Auto Power Off : Off
Screen Messages : On
Install
Repeat Play : Off
S-VHS : Off
VCR Setup
Tape Select : E180
If you wish to use the tape counter to display the time remaining
on a cassette, you must indicate the type of cassette inserted.
1 After pressing the MENU press the corresponding
,
❷
buttons to select the VCR option.
2 Press the OK or
❿
buttons to select this option.
Result
: The VCR Setup menu is displayed.
3 Press the corresponding
or
❷
buttons, until the Tape
Select option is selected.
4 Press the OK or
❿
buttons as many times as required, until the
correct cassette length is displayed.
E180 E240
E 300 E260
5 Press RETURN twice to exit the menu.
E180
E240
E260
E300
VCR
00259A SV-DVD540/XEB-GB2 10/15/03 5:03 PM Page 26
29
GB
28
GB
Recording a Programme with Automatic Stop
VCR
This function enables you to record up to nine hours (LP) of
programmes.
Your DVD-VCR stops automatically after the requested length of
time.
1 Switch on the television.
2 To monitor the programme being recorded, select the television
channel reserved for use with your DVD-VCR (or the AV input if
used).
3 Insert the cassette on which the programme is to be recorded,
with the window visible and the safety tab intact or the opening
covered with adhesive tape.
Result
: The DVD-VCR is switched on automatically.
4 Select:
◆
The station to be recorded using the
PROG ( or )
buttons
or
◆ The AV1, AV2 or AUX source using the INPUT SEL. button
for a satellite tuner or external video source
Result: The channel number is displayed and the
programme can be seen on the television.
5 Select the recording speed by pressing the SPEED button as
many times as required (see page 27).
6 Hold the REC button (
●
) down for a while to start recording.
Result
: The record indicator appears on the television screen
and DVD-VCR display. An index is recorded on the
tape (see page 37).
7 Press the REC button (
●
) several times to increase the
recording time in:
◆ 30-minute intervals up to four hours
◆ 1-hour intervals up to nine hours
Result
: The length is displayed on the television displays.
The selected programme is recorded for the length of
time requested. At the end of that time, the DVD-
VCR stops recording automatically and power off.
8 If you wish to cancel the recording before the end, press
STANDBY/ON.
☛ If the end of the tape is reached while recording:
◆ The recording stops and power off.
☛ This function is not available in DVD recording
EJECT
AUX
3
OK
6
4
4
5
LENGTH 2:30
SET LENGTH :
PRESS REC
●
Recording a Programme Immediately
Protecting a Recorded Cassette
VCR
VCR
Video cassettes have a safety tab to prevent accidental erasure.
When this tab has been removed, you cannot
record on the tape.
1 If you wish to protect a cassette, break off the tab using a small
screwdriver.
2 To re-record over a protected cassette (safety tab broken),
cover the hole with adhesive tape.
1
Before recording a programme, you must have preset the corres-
ponding station (unless you are recording via an external video
source). If you have not done so, refer to pages 18 and 19.
1 Switch on the television.
2 To monitor the programme being recorded, select the television
channel reserved for use with your DVD-VCR (or the AV input if
used).
3 Insert the cassette on which the programme is to be recorded,
with the window visible and the safety tab intact or the opening
covered with adhesive tape.
Result
: The DVD-VCR is switched on automatically.
4 Select:
◆
The station to be recorded using
the PROG ( or )
buttons
or
◆ The AV1, AV2 or AUX source using the INPUT SEL. button
for a satellite tuner or external video source
Result: The station number is displayed and the programme
can be seen on the television.
5 Select the recording speed by pressing the SPEED button as
many times as required (see page 27).
6 Hold REC (
●
) down for a while to start recording.
Result
:
The record indicator appears on the television and
DVD-VCR display. An index is recorded on the tape
(see page 37).
7 To stop recording, press
■
once.
➢ ◆ If your DVD-VCR ejects the cassette when you start
recording, check to make sure that the cassette’s
safety tab is intact or that the opening (created by a
broken safety tab) is covered with adhesive tape.
◆ If you reach the end of the tape while recording,
the cassette rewinds automatically.
OK
7
OK
6
4
4
5
00259A SV-DVD540/XEB-GB2 10/15/03 5:03 PM Page 28
31
GB
30
GB
Modifying ShowView Programming
VCR
If you wish to correct the programme displayed or modify certain elements, such as the recording speed,
you can do so before you press RETURN a second time to confirm.
If you wish to... Then...
Select an input source other ◆ Press the
➛
or
❿
buttons, until the PR selection mode.
than the tuner (AV1, AV2 or AUX)
◆ Press the INPUT SEL. button one or more times to change the
input source selection.
Result
: The programme number is replaced by:
• The AV1, AV2 or AUX source using the INPUT
SEL. button for a satellite tuner or external video
source
➢ The input source must be selected before changing any other
value.
Record a programme every day ◆ Press the
➛
or
❿
buttons, until the Day selection mode.
(Monday to Sunday) at the same time
◆ Press the
or
❷
buttons, until the DLY (Daily) value is
displayed.
Record a programme every week ◆ Press the
➛
or
❿
buttons, until the Day selection mode.
on the same day and at the same time
◆ Press the
or
❷
buttons, until the W- (Week) value is
displayed, followed by the required day.
Example
: W-SA (Weekly Saturday)
Extend the recording time ◆ Press the
➛
or
❿
buttons, until the Stop selection mode.
◆ Press the
or
❷
buttons to increase or decrease the stop
time.
Select the recording speed ◆ Press the
➛
or
❿
buttons, until the recording speed selection
mode.
◆ Press the
or
❷
buttons until the correct indication is
displayed:
• Auto (Auto Tape Speed Select) : see page 32
• SP (Standard Play)
• LP (Long Play)
Select the PDC recording ◆ Press the
➛
or
❿
buttons, until the PDC off mode.
◆ Press the
or
❷
buttons until the “On” indication is displayed.
☛
Do not select PDC unless you are sure the programme you
wish to record is broadcast with PDC. If you do set PDC On
(by selecting “On” in the right - hand column on the screen),
then you must set up the start-time EXACTLY according to
the published TV schedule. Otherwise the timer recording
won’t take place.
Using the ShowView
TM
Before presetting your DVD-VCR:
◆ Switch on both the television and your DVD-VCR
◆ Check that the date and time are correct
◆ Insert the cassette on which the programme is to be
recorded (safety tab intact)
Up to six programmes can be preset.
1 To enter a ShowView, press the TIMER button.
Press the
or
❷
and OK or
❿
buttons to select ShowView
Result: A message is displayed to allow you to enter the
ShowView code.
☛ If all six programmes have been set, the message Timer
is full is displayed. Refer to page 33 if you wish to
cancel a preset recording.
2 Press the numeric buttons to enter the code opposite the
programme that you wish to record in your television magazine.
➢ If you wish to correct the ShowView code that you are
entering:
◆ Press the
➛
button until the digit to be corrected is
cleared
◆ Enter the correct digit
3 Press the OK button.
Result
:
The information concerning the programme is
displayed.
☛ When using the ShowView function for the first time with
stored stations, the programme number flashes. This one
time, you must enter the station number manually by
pressing the
or
❷
buttons. Refer to the following page
if:
◆ The programme number or times flash
◆ You wish to modify the programme
4 If the programme and times are correct, press the RETURN
button.
5 Press the STANDBY/ON button to activate the timer.
6 Refer to page 33 if you wish to:
◆ Check that your DVD-VCR has been programmed correctly
◆ Cancel a preset recording
☛ The numbers next to each TV programme listing are
ShowView code numbers, which allow you to
programme your videorecorder instantly with the
remote control. Tap in the ShowView code for the
programme you wish to record.
™ ShowView is a trademark of Gemstar Development Corporation. The ShowView system
is manufactured under licence from Gemstar Development Corporation.
ShowView
Code
Code : 0 - 9
Correct :
Standard
ShowView
Timer Method
PR Day Start Stop Speed V/P
WE 1 19 : 00 19 : 30 SP Off
::
::
::
::
::
OK
OPEN/CLOSE
STANDBY/ON
5
1
VCR
00259A SV-DVD540/XEB-GB2 10/15/03 5:03 PM Page 30
33
GB
32
GB
Checking a Preset Recording
Cancelling a Preset Recording
VCR
VCR
You can check your preset recordings:
◆ When you have finished presetting the DVD-VCR
◆ If you have forgotten which programmes will be
recorded
1 Press TIMER on the remote control.
Result
: The timer selection is displayed.
2 Press the OK button to select Standard option.
Result
:The TIMER PROGRAMMING menu is displayed.
3 Press the
or
❷
buttons to select the required programme.
4 Press the
➛
or
❿
buttons to select and change any values as
required. For more details, refer to the previous page.
5 On completion, press RETURN twice.
You can cancel any programmes that are:
◆ Incorrect
◆ No longer required
1 Press TIMER on the remote control.
Result
: The timer selection is displayed.
2 Press the OK button to select Standard option.
Result
: The TIMER PROGRAMMING menu is displayed.
3 Select the programme to be cancelled by pressing the
or
❷
buttons.
4 Press the CLEAR button to cancel the selected programme.
Result
: All the recording information is deleted and the
broadcast will not be recorded.
5 On completion, press RETURN twice.
4
PR Date Start Stop Speed V/P
WE 1 19 : 00 19 : 30 SP Off
::
::
::
::
::
PR Date Start Stop Speed V/P
WE 1 19 : 00 19 : 30 SP Off
::
::
::
::
::
Using the Timer Programming Feature
The Timer Programming feature allows you to preset the DVD-
VCR to record a programme up to one month before that
programme is to be broadcast. Up to six programmes can be
preset.
☛ Before presetting a recording, check that the date and
time are correct.
1 Insert the cassette and press TIMER on the remote control.
Result
: The timer selection is displayed.
2 Press the OK button to select Standard option.
Result
: The TIMER PROGRAMMING menu is displayed.
3 Press
❿
to select the input source.
4 Select the required station by pressing the
,
❷
buttons or
INPUT SEL.
to select the AV1, AV2 or AUX input sources.
5 Press
❿
to select the recording day.
6 Select the required day by pressing the
or
❷
buttons.
7 Press
❿
to select the recording start time.
8 Select the required hour value by pressing the
or
❷
buttons.
9 Press
❿
to select the minutes.
10 Select the required minute value by pressing the
or
❷
buttons.
11 Press
❿
to select the recording stop time.
12 Select the required recording stop time by pressing the
or
❷
buttons, following the same procedure as when selecting the
recording start time.
13 Press
❿
to select the recording speed.
14 Press the
or
❷
buttons to select the SP (Standard Play), LP
(Long Play), Auto (Auto Tape Speed Select) recording speeds.
15 Press the
or
❷
buttons to toggle between the PDC
mode (marked
On) and the non PDC mode (marked Off).
16 When you have finished, press the RETURN button.
17 Press the STANDBY/ON button to activate the timer.
Result
: Before starting recording, the DVD-VCR compares
the timer duration with the remaining time on the
cassette.
➢ Auto Tape Speed Select. The DVD-VCR’s “Auto Tape
Speed Select” function compares the duration of the
timer recording to the actual recording time remaining
on the tape loaded. If there is insufficient tape to
complete a timer recording in AUTO mode, the DVD-
VCR automatically switches to LP mode to record the
whole programme.
VCR
OPEN/CLOSE
STANDBY/ON
17
Standard
ShowView
Timer Method
PR Day Start Stop Speed V/P
WE 1 19 : 00 19 : 30 SP Off
::
::
::
::
::
00259A SV-DVD540/XEB-GB2 10/15/03 5:03 PM Page 32
35
GB
34
GB
Selecting the Audio Output Mode
VCR
Playing a Cassette in Slow Motion
You can select the mode in which the sound is reproduced on the
loudspeakers and AV outputs. The following options are
available.
Option Description
L Used to listen to the sound on the left Hi-Fi channel.
R Used to listen to the sound on the right Hi-Fi channel.
MIX Used to listen to the mixed sound of the Hi-Fi and
normal channels.
MONO Used to listen to the sound on the normal mono
channel.
L R Used to listen to Hi-Fi stereo sound on the left and right
channels.
➢ When playing back tapes recorded in Hi-Fi, the
sound switches to Hi-Fi after five seconds of
Mono.
To select the sound mode, simply press the AUDIO button on the
remote control until the required option is displayed.
L R MIX
L R MONO
You can play a cassette in slow motion.
➢ No sound is heard when playing back a cassette in
slow motion.
1 Press:
◆
❿ll
to start playing the cassette
◆
❿ll
button one more time to make still mode.
◆
❿❿
to start SLOW mode.
◆
❿❿
or
➛➛
button as many times as required to decrease or
increase the speed respectively
◆
T
o return to the normal speed, press the
❿ll
button twice.
2 When playing back in slow motion, picture interference may
occur.
Press the TRK ( or ) buttons to minimize this effect.
☛ When you have been using the Slow Motion function
for more than about two minutes, the DVD-VCR will
automatically play to protect the:
◆ Cassette
◆ Video heads
2
2
1
1
VCR
This function allows you to play back any pre-recorded cassette.
1 Switch on both the television and your DVD-VCR.
2 Insert the video cassette to be played. If the safety tab on the
cassette is intact, press
❿ll
.
Otherwise, the cassette is played automatically.
➢ When a cassette is loaded, the tape position is optimized
automatically to reduce disturbance (Digital Auto
Tracking).
When playing a cassette, if the end of the tape is reached,
the cassette is rewound automatically.
NTSC tapes can be played back but cannot be recorded
with this DVD-VCR.
3 To... Then press...
Stop the playback
■
(STOP).
Eject the cassette (EJECT).
Playing a Cassette
EJECT
AUX
3
2
3
Adjusting Picture Alignment Manually
The Picture Adjustment feature allows you to adjust the
alignment manually to obtain the best possible picture.
When noise bars or streaks appear during playback, adjust alignment
manually by pressing the TRK ( or ) buttons until the picture is clear
and stable.
Result
: ◆ The tracking bar appears.
◆ The image is adjusted.
◆ The tracking bar disappears when you release the button.
VCR
VCR
00259A SV-DVD540/XEB-GB2 10/15/03 5:03 PM Page 34
37
GB
36
GB
Searching for a Specific Sequence
Each time you record a cassette on this DVD-VCR, an “index” is
automatically marked on the tape when recording starts.
The Search function allows you to fast-forward or rewind to a
specific index and start playback from that point. Depending on the
direction selected, the indexes are numbered as follows:
➢ This DVD-VCR uses a standard indexing system (VISS).
As a result, it will recognize any indexes marked by other
VCRs using the same
system and vice versa.
Go to 0:00:00 Stop
Use this feature when you want to search for the 0:00:00 counter position
on a cassette. Press the CLEAR button at the point on the tape where you
want to set the counter to 0:00:00.
The VCR will rewind or fast forward, searching for the 0:00:00 counter
position, and then automatically stop at that position.
1 After pressing the SEARCH, press the corresponding
or
❷
buttons, until the Go To (0:00:00) option is selected.
2 Press the OK or
❿
.
End Search
Use this feature when you want to search for a blank position to record a
program on a cassette.
The VCR will fast forward, searching for a blank position, and then
automatically stop at that position.If the VCR reaches the end of the tape
during end search, the tape will be ejected.
1 After pressing the SEARCH, press the corresponding
or
❷
buttons, until the End Search option is selected.
2 Press the OK or
❿
.
21 12
➞
etc.
Prev
Seq.
Seq. being
played
Next
Seq.
etc.
OK
VCR
Playing a Sequence at Variable Speeds
Playing a Sequence Frame by Frame
VCR
VCR
You can:
◆ Stop the cassette at a given frame (image)
◆ Advance one frame at a time
➢ No sound is heard when playing back frame by frame.
1 Press:
◆
❿ll
to start playing the cassette
◆
❿ll
button one more time to make still mode.
◆
F.ADV/STEP ( )
to advance frame by frame
2 To return to normal playback, press
❿ll
.
➢ Vertical stability: When playing back frame by frame,
interference may be seen on the screen. Press the TRK
(,)buttons to minimize this effect.
You can vary the playback speed using the Shuttle function (up to
nine times the normal speed).
Example
: You wish to analyze a sportsperson’s technique,
movement by movement.
The Shuttle function is available on the Remote control
➢ No sound is heard when playing a sequence at variable
speeds.
1 Press:
◆
❿ll
during playback
◆ SHUTTLE (
<<
) to play the cassette backwards
◆ SHUTTLE (
>>
) to play the cassette forwards
2 Each time you press a SHUTTLE button, the speed is changed
as shown in the following illustration.
1
1
1
REVERSE REVERSE REVERSE SLOW SLOW PLAY PLAY PLAY
PLAY PLAY PLAY STILL MOTION MOTION PLAY X3 X5 X9
X9 X5 X3 X1/10 X1/5
1
00259A SV-DVD540/XEB-GB2 10/15/03 5:03 PM Page 36
/