Blue Sea Systems 7517 Operating instructions

  • Hello! I am an AI chatbot trained to assist you with the Blue Sea Systems 7517 Operating instructions. I’ve already reviewed the document and can help you find the information you need or explain it in simple terms. Just ask your questions, and providing more details will help me assist you more effectively!
EV Battery Charger Display
PN 7517
The EV Battery Charger Display provides two options to monitor your battery banks. When
connected to a P12 Battery Charger it can display the charger’s Summary screen—displaying
voltage, current, charging stage, and errors from the charger. When the charger is off or if no
P12 charger is connected, the unit will display the voltage on up to 3 battery banks in an easy
to read bar graph display.
Specications
Display Size: 55mm x 28mm
Display Type: Yellow OLED
Input Voltage: 6 to 36 Volts DC, reverse polarity protected
Amperage Draw:
Maximum: 50 mA
Minimum: < 1 mA in Standby Mode
Standby Mode The 7517 has the option of a power saving
Standby Mode which turns the display off after 4
hours of being stationary. The 7517 will resume
normal function upon movement of the vehicle or by
tapping the unit several times in succession.
Accuracy: ± 1% at 36 Volts DC
Number of Inputs: 3 battery inputs with common reference.
Regulatory
Monitor face is IP66 – protected against powerful water jets when
installed according to instructions.
Please read and understand all instructions before beginning installation.
Note: Pins 1 (Battery 1+) and G (DC Negative) are the power source for the
unit and must be connected.
1) Disconnect all AC and DC sources.
2) Carefully prepare cut out hole for unit installation.
a. Check for pipes, wires, or other systems behind planned cutout area.
3) Set DIP Switches on back of unit for desired display setup. See page 2
4) If connecting to multiple banks, ensure all banks have a
Common Ground.
5) Run appropriately sized wires (see Wire Size / Length Chart) from the
Positive of each bank and the Common Ground to the 4 position terminal
block plug (included), leaving the fuses out of lines 1, 2, and 3 for now.
6) Place gasket around unit.
7) Insert 4 position terminal block plug into unit. It is keyed and will only
go one way.
8) If a P12 charger is installed, connect it to the EV Battery Charger
Display using the Cat5e cable included.
9) Install unit into cutout.
a. Do not overtighten screws.
10)Insertfusesintolines2and3rst.Theninsertfuseintoline1.All
fuses must be appropriately sized for the wiring used.
page 1 of 2
p 360.738.8230
p 800.222.7617 USA and Canada
f 360.734.4195
www.bluesea.com
4. Four Position
Connector
3. 25ft (7.8m) Cat5e Cable
1. EV Battery Charger Display
2. Mounting Gasket
Blue Sea Systems, Inc.
425 Sequoia Drive
Bellingham, WA 98226 USA
Included Components
Wiring and Installation
Connector Pin Assignment
Wire Size / Length Chart
4 Pin Connector* Function
1 Required Connection Battery 1+
2 Battery 2+
3 Battery 3+
G Required Connection DC Negative
* The 4 Pin Connector supports wire sizes from 1224 AWG
** All batteries must share a common ground
Length of Run - One way
feet (meters)
Minimum
Wire Gauge
Recommended
Fuse Size (min-max)
0 10ft (0 3m) 22 AWG 1A 2A
11 20ft (3 6m) 18 AWG 1A 10A
21 40ft (6 12m) 16 AWG 1A 15A
41 70ft (12 21m) 14 AWG 1A 20A
71 100ft (21 30m) 12 AWG 1A 25A
Battery 2 Battery 3Battery 1
Fuse
G 3 2 1
7517 EV Battery Charger Display Back
CAT5 Cable
Negative Busbar
Fuse
Fuse
P12 Battery Charger Connections View
RJ45
Remote
Port
ON
1 2
980023670 Rev. 001 page 2 of 2
Bar Graph
Use if a P12 charger is not connected or the charger
summary screen is not desired. When a P12 is
connected, the display will show a lightning bolt
when the charger is active. The bar graph will
indicate when a channel is in Bulk or Absorption
modes by a “Filling Up” graphic. When a channel
moves to Pre-Float or Float mode the graphic will
stop, this will occur independently for each channel.
1 2
ON
ON
1 2
ON
1 2
ON
1 2
3.500"
(88.90mm)
2.063"
(52.39mm)
3.900"
(99.06mm)
2.375"
(60.33mm)
.200"
(5.08mm)
.150"
(3.81mm)
.188" (4.76mm)
3/16"
X 4 HOLES
CUT OUT 3 1/2" X 2 1/16"
Wiring Diagram
Mounting Cutout
Dip Switch Settings
(OFF-OFF)
(ON-OFF)
(OFF-ON)
(ON-ON)
Cutout is scaled 1:1. Do not scale.
With
Standby
Mode*
(Default)
Without
Standby
Mode
With
Standby
Mode*
Without
Standby
Mode
* Standby Mode: Seespecications
P12 Summary Screen
When the connected P12 charger is ON, the
unit will display the charger summary screen.
When the connected P12 charger is off, the
unit will display the bar graph display.
/