GE Profile PEP7030DT Owner's manual

Type
Owner's manual

GE Profile PEP7030DT is a 30-inch built-in electric cooktop with a sleek touch-control interface and a host of features to make cooking easier and more efficient. With its dual-ring element and power boil function, you can quickly bring water to a boil for pasta or vegetables. The precision temperature control ensures accurate cooking, while the guided cooking feature provides step-by-step instructions for a variety of recipes. The glide touch controls offer 11 precise heat settings, giving you ultimate control over your cooking.

GE Profile PEP7030DT is a 30-inch built-in electric cooktop with a sleek touch-control interface and a host of features to make cooking easier and more efficient. With its dual-ring element and power boil function, you can quickly bring water to a boil for pasta or vegetables. The precision temperature control ensures accurate cooking, while the guided cooking feature provides step-by-step instructions for a variety of recipes. The glide touch controls offer 11 precise heat settings, giving you ultimate control over your cooking.

For answers to your Monogram, GE Café, GE Profile or GE Appliances
product questions, visit our website at geappliances.com or call
GE Answer Center® Service, 800.626.2000.
PEP7030DT
GE Profile 30" Built-In Touch-Control Electric Cooktop
Specification Revised 03/23
ADA
COMPLIANT
Listed by
Underwriters
Laboratories
IMPORTANT: Requires a 5" free area between the
bottom of the cooktop to any combustible material,
i.e., shelving. Free area not required when installing
wall oven underneath cooktop. Refer to installation
instructions. Requires a 15" minimum from cooktop
to adjacent overhead cabinets. Units are furnished
with a 48" flexible armored cable.
NOTE: 30" Ribbon cooktops are approved for use
over select GE 27" and GE 30" Single Wall Ovens
and Warming Drawers. Refer to cooktop and wall
oven/warming drawer installation instructions
packed with product for current dimensional
data. If installed with a GE Telescopic Downdraft
System, consult both the cooktop and downdraft
installation instructions packed with product before
installing. Cooktop gas/electric supply may need to
be re-routed to install downdraft. The countertop
cutout requires 23-1/2" minimum flat countertop
surface and 25" minimum total countertop depth.
In addition, other clearances to front edge of the
countertop must be considered. Before installing,
consult installation instructions packed with
product for current dimensional data.
CUTOUT FILLER TRIM KIT: A filler trim kit is
available for use if your countertop cutout is larger
than the dimension shown, up to 29-13/16" x
20-7/16". Order JXTR32B for black or JXTR32W for
white, to reduce the cutout opening for installation
of this cooktop. These kits may be ordered from
your GE Appliances Dealer.
DIMENSIONS AND INSTALLATION INFORMATION (IN INCHES)
To insure accuracy, it is best to make a
template when cutting the opening in the counter
Cooktop
29-3/4" 20-7/8"
19-1/4" 28-1/16"
19-5/8" to
19-3/4"
28-1/2" to
28-5/8"
2-1/2" MIN.
Required
1-3/4" MIN.
to rear wall
3-9/16" at front of unit and
5-9/16" at conduit location
13" MAX. depth of unprotected
overhead cabinets
30" MIN. Clearance from
countertop to unprotected
overhead surface
2" MIN. Clearance
from cutout to
nearest vertical
wall or cabinet on
left side of the unit
below the 15" MIN.
clearance height.
1 1/2" MIN. (30") and
2" MIN. (36") Clearance
from cutout to nearest
vertical wall or cabinet
on right side of the unit
below the 15" MIN.
clearance height.
30" MIN. for
30" cooktop
15" MIN. height
from countertop
to nearest cabinet
(including light rails)
on both sides of
cooktop
APPROXIMATE COOKING DIMENSIONS
VOLTAGE (60HZ AC) 240V 208V
CONNECTED LOAD (MAX.) 9.5kW 7.1kW
CURRENT DRAW (MAX.) 39.6 Amps 34.3 Amps
RECOMMENDED CIRCUIT BREAKER40 Amps 40 Amps
NOTE: Check local codes for required breaker size.
2-1/2" MIN
From front edge
of countertop to front
edge of cooktop cutout
31-1/4" MIN
From top surface
of countertop to
top surface of
wall oven support
platform
INSTALLATION ABOVE A WALL OVEN
INSTALLATION ABOVE A WALL OVEN
PEP7030DT
GE Profile 30" Built-In Touch-Control Electric Cooktop
Specification Revised 03/23
HOT
Low
High
HOT
Warm
High
HOT
Melt
High
APP PREHEATING
C
F
o
APP PREHEATING
C
F
o
Timer
Cancel Hold 3 Sec
HR MIN
TAP COOKWARE SET TEMP
Precision
Cooking
Wi-Fi
Connect
Connect
Bluetooth
Controls
Lock
Hold 3 Sec
All O
Burners
Sync
HOT
Low
P
o
w
e
r
B
o
i
l
Warm
Power Boil
Melt
FEATURES AND BENEFITS
Power Boil on Dual-Ring Element
Precision Temperature Control
Guided Cooking
Glide Touch Controls - 11 Control Levels
Easy Clean Surface
Synchronized Elements
Chef Connect
Built-in WiFi
Compatible Cooktop with Smart Cookware
Keep Warm Setting
Control Lock
Hot Surface Indicator Lights
Fit Guarantee
Model PEP7030DTBB – Black on black
OPTIONAL FILLER TRIM KIT
Fill in any counter top gaps with this filler trim kit. Order part
number JXTR32B.
GUARANTEED FIT
Replacing a similar cooktop from GE Appliances or another
brand? GE cooktops are guaranteed for an exact fit or
GE Appliances will pay up to $100 toward modifications.
Visit geappliances.com for more info.
COMPATIBLE COOKTOP WITH SMART COOKWARE
Smart pans easily pair with this smart cooktop to ensure you
get the perfect cooking results. Accessories sold separately.
  • Page 1 1
  • Page 2 2

GE Profile PEP7030DT Owner's manual

Type
Owner's manual

GE Profile PEP7030DT is a 30-inch built-in electric cooktop with a sleek touch-control interface and a host of features to make cooking easier and more efficient. With its dual-ring element and power boil function, you can quickly bring water to a boil for pasta or vegetables. The precision temperature control ensures accurate cooking, while the guided cooking feature provides step-by-step instructions for a variety of recipes. The glide touch controls offer 11 precise heat settings, giving you ultimate control over your cooking.

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI