PHP9030SJ/BM
GE Profile
™
Series 30" Built-In Touch-Control Induction Cooktop
For answers to your Monogram, GE Café
™
Series, GE Profile
™
Series or
GE Appliances product questions, visit our website at geappliances.com
or call GE Answer Center
®
Service, 800.626.2000.
ADA
COMPLIANT
Listed by
Underwriters
Laboratories
Specification Revised 1/19
To insure accuracy, it is best to make a
template when cutting the opening in the counter
Electrical junction box 16" MIN.
below countertop
Cooktop
29-7/8"
21"
19-1/4"
28"
19-5/8"
to 19-3/4"
2-1/2" MIN.
Required
28-1/2" to
28-5/8"
1-3/4" MIN.
to rear wall
PHP9030SJ
4-5/8" at baffle near center
ofunit (except when installed
above an approved wall
oven) and 3-1/4" at rear
of air intake
13" MAX. depth of unprotected
overhead cabinets (when no
hood or microwave is installed)
30" MIN. from countertop to
unprotected cabinet (when
no hood or microwave is
installed)
2" MIN. clearance
to side wall from cut-out
on both sides of cooktop
15" MIN. height from countertop
to nearest cabinet (including
light rails) on both sides of
cooktop
IMPORTANT: Requires a 3" free area between
the bottom of the cooktop to any combustible
material, i.e., shelving. Free area not required
when installing wall oven underneath cooktop.
Refer to installation instructions. Requires a 15"
minimum from cooktop to adjacent overhead
cabinets. Units are furnished with a 48" flexible
armored cable.
NOTE: 30" induction cooktops are approved
for use over select GE 27" and GE 30" Single
Wall Ovens and Warming Drawers. Refer
to cooktop and wall oven/warming drawer
installation instructions packed with product for
current dimensional data. If installed with a GE
Telescopic Downdraft System, consult both the
cooktop and downdraft installation instructions
packed with product before installing. Cooktop
gas/electric supply may need to be re-routed to
install downdraft. The countertop cutout requires
23-1/2" minimum flat countertop surface and 25"
minimum total countertop depth. In addition,
other clearances to front edge of the countertop
must be considered. Before installing, consult
installation instructions packed with product for
current dimensional data.
CUTOUT FILLER TRIM KIT: A filler trim kit
is available for use if your countertop cutout
is larger than the dimension shown, up to
29-13/16" x 20-7/16". Order JXTR32B for black or
JXTR32W for white, to reduce the cutout opening
for installation of this cooktop. These kits may be
ordered from your GE Appliances Dealer.
DIMENSIONS AND INSTALLATION INFORMATION (IN INCHES)
APPROXIMATE COOKING DIMENSIONS
KW RATING
240V 7.4
208V 6.4
AMPERAGE
240V 40 Amps
†
208V 40 Amps
†
†
NOTE: Check local
codes for required
breaker size.
2-1/2" MIN
From front edge
of countertop to front
edge of cooktop cutout
31-1/4" MIN
From top surface
of countertop to
top surface of
wall oven support
platform
INSTALLATION ABOVE A WALL OVEN
INSTALLATION ABOVE A WALL OVEN
PHP9030SJ/BM
GE Profile
™
Series 30" Built-In Touch-Control Induction Cooktop
Specification Revised 1/19
PHP9030SJSS
FEATURES AND BENEFITS
Four Induction elements – Enjoy a new level of rapid, precise heating
with a cool-to-the-touch surface that’s easy to clean
Digital touch controls – Accurately control your heating and enjoy an
easy to clean surface
11" 3,700-watt induction element – Rapidly boil water with
GE Appliances' most powerfull induction element
SyncBurners – Control two 7" elements simultaneously to evenly heat
large cookware or griddles*
Kitchen timer – Helps coordinate meal preparation and cooking
Control lock capability – Protects against unintended activation
Pan presence & size sensor – Cook efficiently with elements that heat to
the size of your pan and shut off when no pan is present
Red LED display with black glass surface and stainless steel trim –
Achieve a modern look that complements the entire kitchen and other
stainless steel appliances
Hot surface indicator lights – Know when elements are too
hot to touch with a quick glance
Model PHP9030SJSS – Stainless Steel
Model PHP9030BMTS – Black stainless
* OPTIONAL STAINLESS STEEL CLAD
ALUMINUM GRIDDLE
Achieve even results with this lightweight griddle,
tailored to fit GE SyncBurners. Order part number
JXGRIDL1 from your GE Dealer.
GUARANTEED FIT
Replacing a similar cooktop from GE Appliances or another brand?
GE cooktops are guaranteed for an exact fit or GE Appliances will
pay up to $100 toward modifications
Visit geappliances.com for more info
-
1
-
2
Ask a question and I''ll find the answer in the document
Finding information in a document is now easier with AI
Related papers
Other documents
-
GE Appliances PHP9030BMTS Owner's manual
-
GE Profile PEP7036DT User manual
-
GE Profile PEP7030DT Owner's manual
-
GE Profile PEP9030ST User manual
-
GE Profile JP5030DJ 30 Inch Built-In Touch-Control Electric Cooktop Owner's manual
-
-
GE Appliances PHP9036DJ User manual
-
Cafe CEP90301NBB Dimensions Guide
