MULTISPAN VOLT-19 Owner's manual

Brand: MULTISPAN

Model: VOLT-19

Type: Owner's manual

VOLT 19

FEATURES :

INPUT SPECIFICATION :

DISPLAY AND KEYS :

AUXILIARY SUPPLY :

GENERAL SPECIFICATION :

3 Line 3 digit bright LED display,

3 PHASE VOLT METER

Display

Supply voltage

Dimension (mm)

Keys

Power consumption

(VA RATING)

3 digit, 3line, 7 seg, 0.56” RED LED

96 (H) x 96 (W) x 43 (D) mm

INC, DEC (Scroll)

ENVIRONMENT CONDITION :

NETWORK CONNECTION :

Relative Humidity

Protection Level

(As per request)

Operating Temp. 0°C to 55°C

UP to 95% RH

(non-condensing)

IP-65 (Front side) As per IS/IEC

60529 : 2001

100 to 270V AC,50/60Hz

TECHNICAL SPECIFICATION

MECHANICAL INSTALLATION

Measure Parameter VLL - VLN (3Ø - 4W)

VLL (3Ø - 3W)

TERMINAL CONNECTION

3Ø-3W/3Ø-4W

Network Selection 3Ø-3W/3Ø-4W

Class 0.5 (Standard)

ACCURACY

Panel Cutout 92 (H) x 92 (W) mm

Outline Dimension (mm) Panel Cutout

Dimension (mm)

VOLT 19

4 1 5

4 2 0

4 2 1

30 to 300V (L - N)

< 0.2 VA

45.0 to 65.0 Hz

50 to 520V (L - L)

Burden

(Direct voltage AC)

Frequency

Primary PT Ratio

Rated voltage Ac

100V to 520KV (Programmable)

Secondary PT Ratio 100V to 520V (Programmable)

Voltage AC

PARAMETER SETTING

Enter Password = 19

PT Ratio

100V - 520KV

p T R

4 1 5

PT Ratio

Secondary

100V to 520V

Network Selection

3Ø - 3W/4W

P A S

1 9

p t r

s e C

4 1 5

n e t

Change by &

Press + Key

Press + Key for 5 sec to

enter into parameter setting

p R I

Primary

3 - 4

Change by &

Press + Key

Press + Key to save & exit

Change by &

3VA

Page -1

1 2 3 4 78910

20 19 18 17 14 13 12 11

16 15

VL1VL2VL3N

L N

3Ph-4W/3Ph-3W

Accuracy Class: 0.5

Range: System:

www.multispanindia.com

50/60 HZ

3VA

100

270V AC

VOLT-19-A2-N0

Made in India

Primary PT: 100V to 520KV AC

Secondary PT: 100V to 520V AC

Voltage(L-L) : 50-520V AC

(L-N) : 30-300V AC

Page -2

KEY OPERATION

To enter in parameter setting

To view individual phase voltage

PRESS KEYFUNCTION

OPERATOR MODE

PARAMETER SETTING MODE

It is used to set parameter value

and to be save & exit from menu

To increment value in parameter

setting

To decrement value in parameter

setting

For 5 sec

Read complete instructions prior to installation

and operation of the unit.

WARNING : Risk of electric shock.

SAFETY PRECAUTION

All safety related codifications, symbols and instructions

that appear in this operating manual or on the equipment

must be strictly followed to ensure the safety of the operating

personnel as well as the instrument.

If all the equipment is not handled in a manner specified

by the manufacturer, it might impair the protection provided

by the equipment.

WARNING GUIDELINES

WARNING : Risk of electric shock.

1) To prevent the risk of electric shock, power supply to the

equipment must be kept OFF while doing the wiring

arrangement. Do not touch the terminals while power is

being supplied.

2) To reduce electro magnetic interference, use wire with

adequate rating and twists of the same of equal size shall

be made with shortest connection.

3. Cable used for connection to power source, must have a

cross section of 1mm or greater. These wires should have

insulations capacity made of at least 1.5kV.

4) A better anti-noise effect can be expected by using

standard power supply cable for the instrument.

1) Do not allow pieces of metal, wire clippings, or fine

metallic fillings from installation to enter the product or

else it may lead to a safety hazard that may in turn

endanger life or cause electrical shock to the operator.

2) Circuit breaker or mains switch must be installed

between power source and supply terminal to facilitate

power ‘ON’ or ‘OFF’ function. However this mains switch

or circuit breaker must be installed at convenient place

normally accessible to the operator.

INSTALLATION GUIDELINES

3) Use and store the instrument within the specified ambient

temperature and humidity ranges as mentioned in this

manual.

MECHANICAL INSTALLATION

DISPLAY PAGE

1) To install the instrument on a DIN rail, raise the clamp at the

back of the instrument and place it on the rail. Now release

the clamp, so the instrument fits on the DIN rail.

2) Ensure proper fitting of the instrument by pulling it outwards.

3) To remove the instrument raise the clamp to release it from

the DIN rail.

1) The equipment should be cleaned regularly to avoid

blockage of ventilating parts.

2) Clean the equipment with a clean soft cloth. Do not use

isopropyl alcohol or any other cleaning agent.

MAINTENANCE

3) Fusible resistor must not be replaced by operator.

3Ø-4W

4) The equipment in its installed state must not come in

close proximity to any heating source, caustic vapors, oil

steam, or other unwanted process byproducts.

5) Do not connect anything to unused terminals.

3Ø-3W

4 1 5

2 3 0

2 2 9

2 2 8

1) Voltage L12-L23-L31

2) Voltage L1-L2-L3

4 1 5

1) Voltage L12-L23-L31

6 3 5

1) Voltage L1-L2-L3

1 1 0

1) Voltage L12-L23-L31

6 3 5

To Scroll & Hold Page

For 5 sec

(Only 3Ø4W)

Specifications are subject to change, since development is a continuous process,

So for more updated operating information and Support,

Please contact our Helpline: +91-9081078683/81 or

Email at Ver:2204[email protected]

MULTISPAN VOLT-19 Owner's manual

MULTISPAN VOLT-19 Owner's manual

MULTISPAN VOLT-19 Owner's manual

Related papers

Other documents