Eagle G009MA Operating instructions

G009MA

12V IP65 RGB LED Tape Light Kit

(5M) with PSU

CONGRATULATIONS ON YOUR PURCHASE

Thank you for purchasing this Eagle Tape Light Kit. Please read these instructions carefully

and leave with the user of the product for future reference. If the product is sold on then the

instruction/manual should pass on as well.

BEFORE USE

You must inspect the product and all accessories including any cables and its power supply

for any signs of damage. If the product is damaged, DO NOT use it, and contact your supplier

immediately.

PRODUCT SAFETY

• Children shall not play with this unit.

• Do not place the mains lead beneath a carpet or a rug.

• Cleaning and user maintenance shall not be made by children without supervision.

• Please ensure the power supply is switched o when not in use.

• Do not leave this device switched on when unattended.

• Though the tape light section of this product is IP rated any connections and its power supply

are not and must be kept dry.

• Periodically check this product and its power supply for damage. If any is detected do not use

and contact your supplier.

• The power supply MUST only be used in a well-ventilated area away from sources of heat and

moisture.

INCLUDED IN THE BOX

1 x 5m Tape Light

1 x 12V 4A In-line power supply

1 x IR Remote Control

1 x IR Receiver

OPERATION AND INSTALLATION

• Installation must take place whilst the unit is unplugged

• The product MUST NOT be mounted using staples, nails, or metal xings.

• The product can be cut at 5cm (3 LED) intervals to the required length, highlighted by a line

straddled with a pair of scissors. This cut can be made with regular scissors (not supplied). Cut

ends must be sealed with heat shrink (not supplied) or similar water repellent type materials.

• The product can be installed in the desired location simply by removing the self-adhesive

backing on the rear of the tape light and then pressing the tape light against a smooth clean

surface. The surface must be free of dust and grease.

• Apply rm pressure along the length of the tape light to ensure it has adhered in all locations.

• Once installed, plug the product in and switch the mains power on.

• Ensure the product is switched o when not in use.

1) Cut the product to length as required (can be cut every 5cm) before installation.

2) Install the product into position by peeling o the backing and xing in place.

3) Join the end connection of the tape with the IR receiver module (as per below)

4) Connect the power supply to the IR receiver and switch on

5) The product can be controlled via the remote control.

OFF

RGB

FLASH

STROBE

FADE

SMOOTH

Brightness

White

Colour

Selection

Programs

MAINTENANCE

There are no user serviceable parts in this product. Periodically check the product for LED failure

and damage. If any of the LED’s have failed or the product is damaged in anyway switch o

and disconnect from the mains supply. To clean the product, switch o and disconnect from the

mains supply. Using a slightly damp cloth gently wipe over. Do not use bleach, solvent based

cleaners or strong detergents. These may damage the product and invalidate the warranty. If

the mains lead is damaged, it must be replaced by the manufacturer or and authorised service

centre.

PAT TESTING

When used in an oce environment, we recommend that this product should be safety-tested

yearly by a qualied electrician (PAT Tested). We recommend that it is PAT tested regularly when

used in a domestic environment.

GENERAL SAFETY REQUIREMENTS

Domestic wiring must be tested periodically by a qualied electrician at least once every 10

years or at every change of occupancy. For oce and retail premises, and buildings such as

village halls, the wiring must be inspected at least once every 5 years. It is recommended that all

building be tted with smoke alarms (it is mandatory for new buildings).

TECHNICAL SPECIFICATION

Tape Dimensions: ...............................................................................................2.5 x 10 x 5000mm

Weight: ...................................................................................................................................0.45kg

PSU Input: ............................................................................................................................. 230V ~

PSU Output: ........................................................................................................................12V - 4A

Power consumption: ................................................................................................................. 48W

Remote Battery ....................................................................................................................CR2025

SERVICE WARRANTY

Electrovision Ltd. guarantees the product free from defects in materials and workmanship for

a period of twelve months. Should this product be operated under conditions other than those

recommended, or any attempts are made to service or modify the product, then the warranty

will be rendered void. The product you buy may sometimes dier slightly from illustrations.

This warranty is in addition to, and does not aect, your statutory rights. Our guarantee is

administered by our retailers. If your product arrives damaged, you must contact the retailer

from whom you bought it. The retailer’s contact details will be on the invoice that arrived with the

product, or on the e-mail you received when you placed the order. Do not contact Electrovision,

only your retailer can arrange a replacement. If the product needs to be repaired or replaced, you

must contact the retailer from whom you bought it. If you have just received your product and

require technical help in using it, please call our Help Desk on (0845) 459 4816

Electrovision Ltd, Lancots Lane, Sutton, St. Helens, Merseyside, WA9 3EX

Eagle G009MA Operating instructions

Related papers

Other documents