2. KUFATEC
  3. 35538
35538

KUFATEC 35538 Operating instructions

  • Hello! I'm your chat assistant. I've reviewed the provided brief instruction document, which details the installation and connection of KUFATEC multimedia interfaces and rear view camera systems, including wiring and coding instructions for various head units. I'm ready to assist with any questions you might have regarding the information in this document.
  • What type of video signal does the RVC need?
    What should be done if the image display is incorrect?
    What needs to be done before connecting to MFD2?
1
26
13
1 5
13
35676 (RNS-E)
35677 (MFD2)
head unit
4
C2
35570
connector Interface
10 18
NOTE: If there is an error regarding the display of
the image while putting the vehicle in reverse, you
have to use the Cinch-input on the circuit board
instead.
14
3 5
6
Version 1.03 25.06.2019
Brief instruction multimedia interface
Article-ID 35538 (Basic Plus), 35537 (Basic)
PIN Configuration
RNS-E, MFD2, RNS 510 RNS-D, MFD Comand
14 26
Can High - PIN 9
Can Low - PIN 10
Ground - PIN 12
Red - Steady plus
1 13
Can High - PIN 13
Can Low - PIN 26
Ground - PIN 8
Red - Steady plus Ground - PIN 8
Red - PIN 7
PIN Configuration for factory fitted RVC
In case of factory fitted RVC the loom (35951) has to be connected to the 54-
pole connector of the control unit for RVC.
The control unit can be located on different places within the vehicle.
Vehicle
Location
—
RVC - Control unit
Wiring — Vehicle wiring
Red (Audio) — PIN 5 (if taken remove PIN)
Black (Audio) — PIN 4 (if taken remove PIN)
White (Audio) — PIN 7 (if taken remove PIN)
Blue — PIN 11
Gray — PIN 13
Yellow — PIN 15
Touareg, Tiguan — Behind the cover in the trunk (ride hand side)
Passat 3C Variant — Behind the cover in the trunk (ride hand side)
Audi R8 — Behind the cover driver seat
Wiring — Vehicle wiring
Violett — PIN 17
White — PIN 18
Black/White — PIN 40
Black/Yellow — PIN 39
Brown (Ground) — PIN 44
Red — PIN 43
Fitting after market camera
The RVC has to process NTCS signals!
RNS-E - C2 - RFSL
MFD2 - PIN 6
10 18
1
9
35676 (RNS-E) - Pin C2
35677 (MFD2) - Pin 6
1 9
Article-ID 35570 Black - Pin 5 (Video ground)
Yellow - Pin 14 (Video)
Article-ID 35676 (RNS-E) add on cable - Pin 3
35677 (MFD2/RNS2)
For RNS 510 with softwareindex 522 and higher the CAN-Gateway (Address 19) has
to be coded to TV. Please contact your VW-dealer!
For MFD2 the AV and AUX source have
to be deactivated before connecting.
1 5 9 13
10
4 12 FUSE
1
8
1
7
8
Detailed manual: http://www.kufatec.de/infocenter/download/
F U S E
F U S E
2
14
1 2 3 5
6
6
Fitting original (OEM) RVC
head unit
RNS-E - C2 - RFSL
MFD2 - PIN 6
10 18
1
9
35676 (RNS-E) - Pin C2
35677 (MFD2) - Pin 6
connector Interface
10 18
Furtheremore you need to connect the wiring to the original RVC.
1 9
Article-ID 36136 Black - Pin 5 (Video ground)
Yellow - Pin 14 (Video)
Red - Pin 1 (Plus)
Brown - Pin 2 (Ground)
Article-ID 35676 (RNS-E) add on cable - Pin 3
35677 (MFD2/RNS2)
Coding RVC
• Head unit Audi RNS-E
Address 56 - Chanal 04 - set 0 to 1
The head unit has to have a softwareindex of at least 550.
• Head unit VW RNS 510
• For fitting RVC interface universal
Address 19 - Diagnostic interface - needs to be coded to RVC
• Fitting RVC in connection with multimedia adapter 35538 is not possible
Autom. switch RVC is limited to head unit RNS-E, MFD2/ RNS2, RNS 510
No auto switch for MFD, RNS-D, Comand 2.0, Comand 2.5
For vehicles which do not support the RNS-E - C2 - RFSL MFD2 - PIN 6
10 18
1
9
35676 (RNS-E) - Pin C2
35677 (MFD2) - Pin 6
Control line
Control line needs to be connected to the 2-pole connector of the main loom.
Infrared
connection
Multimedia device
Y-junction
For connection of 2
devices
SETUP as well as operation please see manual mulimedia adpter page 10.
36136
35676 (RNS-E)
35677 (MFD2)
1 5
13
4
C2
Rear-signal through the CAN article-
ID 35676, 35677 can be connected
directly to the rear signal of the car
35676 (RNS-E)
35677 (MFD2)
Rear-Signal
1
5
13
(ONLY RNS-E, MFD2)
4
FUSE
for example Audi A2, A6 (4B)
C2
/