Geovision 84-LPR20-ED1 Datasheet

Brand: Geovision

Model: 84-LPR20-ED1

Category: Security cameras

Type: Datasheet

GV-IRCAM V1.5

Installation Guide

Before attempting to connect or operate this product,

please read these instructions carefully and save this manual for future use.

(10-Meter / 20-Meter Models)

GV-IRCAM offers a selection of models that support different optimal distances and video

formats to meet various needs. This installation guide will take you through the functionality

and use of GV-IRCAM.

List of Models

AC Power Cable (110-125V, 10A) x 1

Power Adapter (100-240V, 12V/3A) x 1

Outdoor Mounting Bracket x 1

Models

Packing List

Model

GV-IRCAM 10M EIA DC12V

GV-IRCAM 20M EIA DC12V

GV-IRCAM 10M CCIR DC12V

GV-IRCAM 20M CCIR DC12V

Optimal Distance

10 m / 32.80 ft

20 m / 65.61 ft

10 m / 32.80 ft

20 m / 65.61 ft

Video Format

NTSC

PAL

Specifications

Model

Distance (optimal)

Sensor

Resolution

Lens Focal Length

Construction

Protection classification

Environmental

Power Supply

Power Consumption

LED Quantity

Illumination Range

Illumination View Angle

Illuminator Life

1/3" B/W EXview CCD

600 TVL

Robust aluminum with weatherproof sun-shield

IP 66

Operation: -20˚C ~ 50˚C / -4˚F ~ 122˚F Storage: -30˚C ~ 60˚C / -22˚F ~ 140˚F

DC 12V

30˚

25,000 hrs

GV-IRCAM 10M

EIA DC 12V

7~15 m /

22.96 ~ 49.21 ft

5 ~ 50 mm, 10X

15W

12 high-efficiency

reflex LED

20M (object of view

reflecting IR light)

GV-IRCAM 20M

EIA DC 12V

15 ~ 25 m /

49.21 ~ 82.02 ft

10 ~ 120 mm, 12X

20W

24 high-efficiency

reflex LED

30M (object of view

reflecting IR light)

GV-IRCAM 10M

CCIR DC 12V

7 ~ 15 m /

22.96 ~ 49.21 ft

5 ~ 50 mm, 10X

15W

12 high-efficiency

reflex LED

20M (object of view

reflecting IR light)

GV-IRCAM 20M

CCIR DC 12V

15 ~ 25 m /

22.96 ~ 49.21 ft

10 ~ 120 mm, 12X

20W

24 high-efficiency

reflex LED

30M (object of view

reflecting IR light)

Installing Camera Module

Push the sun shield forward to align with

the back of camera enclosure.

1. Slightly lift the camera module and slide it

out completely.

Remove the foam.5.

Pull out the camera module.

Sun Shield

Camera Enclosure Back

Camera Module

Completely slide the camera

module out

Loosen the set screws on the back of the

camera enclosure.

Loosen the screw cap on the right.6.

Insert the video cable through the screw

cap and the inside rubber of the cap.

Rubber

Screw Cap

VIDEO OUT Jack

Attach the video cable to the BNC

connector and plug it into the “VIDEO OUT”

jack.

Adjust the length of the video cable and

seal it with the waterproof tape.

Tightly screw the cap.10.

Loosen the screw cap on the left, insert the

power cable through the screw cap and the

inside rubber.

11.

Plug the power cable into the DC jack.12.

Adjust the length of the cable, seal it with

the waterproof tape, and then tightly screw

the cap (see Steps 9 and 10 for the

pictures).

13.

DC Jack

Adjusting Camera Settings

BLCOFF

AUTO IRIS

AI SHUT

SUPERAGC

FLOFF

BLC

CCD-I

NORM

NAGC

r=.45

Overview

Switch Control

Function

Switch Control (For details, see

the chart below.)

Video Out

Power Terminal (It is already

connected. Follow Steps 11 to 12

in Installing Camera Module to

insert the power cable.)

Power LED

The switches on the panel are set by default as the picture below shows.

Switch

FLOFF

BLC

CCD-I

NORM

NAGC

r = .45

Switch

BLCOFF

AUTO IRIS

AI SHUT

SUPERAGC

r = 1

Description

Auto Exposure Mode

Flickerless off

Auto Backlight on

CCD-Iris

Auto Iris + Shutter Mode

Average Convergence

Normal AGC=30dB

GAMMA (.45)

Description

Manual Exposure Mode

Flickerless on

Auto Backlight off

Auto Iris

Auto Iris + Shutter Speed

Peak Convergence

Super AGC=36dB

GAMMA (1)

ME Settings

Shutter Speed Settings

SHUTTER SPEED

1/50(1/60) SEC

1/120(1/100)SEC

1/250 SEC

1/500 SEC

1/1000 SEC (*)

1/2000 SEC

1/4000 SEC

1/10000 SEC

AE/ME

FLOFF

BLC

BLCOFF

BLC

BLCOFF

CCD-I

AUTO IRIS

Notes:

1. The default settings are marked with (*).

2. The gray areas in the charts are not recommended for use.

The default setting is DC.

Gain Control Settings

GAIN

0 dB

6 dB (*)

12 dB

18 dB

AE/ME

NAGC

SUPERAGC

Switch

VIDEO

Description

DC Drive Lens

Video Drive Lens

Auto Iris Selection

DC VIDEO

Installing Camera Enclosure

After the installation of camera module and settings adjustment, you are now ready to install the

camera enclosure back.

1. Adjust the lens focus. 2. Lift the camera module.

Align the camera module to the camera

enclosure and slide it back.

Secure the camera enclosure with the

screws on both sides.

Push the sun shield back.5.

9F, No. 246, Sec. 1, Neihu Rd.,

Neihu District, Taipei, Taiwan

Tel: +886-2-8797-8377

Fax: +886-2-8797-8335

[email protected]

http://www.geovision.com.tw

Geovision 84-LPR20-ED1 Datasheet

Brand: Geovision

Model: 84-LPR20-ED1

Category: Security cameras

Type: Datasheet

Download PDF

report

Geovision 84-LPR20-ED1 Datasheet

Geovision 84-LPR20-ED1 Datasheet

Related papers

Other documents