Bryant LEGACY 580J Submittal Data

Bryant
Brand
Bryant
Model
LEGACY 580J
Category
Split-system air conditioners
Type
Submittal Data

Bryant LEGACY 580J is a single-packaged electric cooling, gas heating unit pre-wired and pre-charged with PuronR (R--410A) HFC refrigerant. The unit is factory tested in both heating and cooling modes and meets ASHRAE 90.1-2007 efficiency levels. It features:

  • SEER’s up to 13.0 (04-- 06 sizes)
  • EER’s up to 11.0
  • IEER 11.2 (07 size only)
  • Non-corrosive composite sloping design; side or center drain condensate pan. Meets ASHRAE Standard 62
  • Standard cooling operating range from 40_F up to 115_F (4_C up to 46_C). Field installable accessory extends the minimum down to - 20_F (-- 29_C

Bryant LEGACY 580J is a single-packaged electric cooling, gas heating unit pre-wired and pre-charged with PuronR (R--410A) HFC refrigerant. The unit is factory tested in both heating and cooling modes and meets ASHRAE 90.1-2007 efficiency levels. It features:

  • SEER’s up to 13.0 (04-- 06 sizes)
  • EER’s up to 11.0
  • IEER 11.2 (07 size only)
  • Non-corrosive composite sloping design; side or center drain condensate pan. Meets ASHRAE Standard 62
  • Standard cooling operating range from 40_F up to 115_F (4_C up to 46_C). Field installable accessory extends the minimum down to - 20_F (-- 29_C
580J
SINGLE PACKAGE ROOFTOP
GAS HEATING/ELECTRIC COOLING UNIT
SIZES 04 -- 07 with PURONr (R--410A) REFRIGERANT
Submittal Data
Certified to ISO
Use of the AHRI Certified
TM Mark indicates a
manufacturer’s
participation in the
program For verification
of certification for individual
products, go to
www.ahridirectory.org.
9001
—or—
DESCRIPTION
580J units are single--packaged electric cooling, gas heating
units that are pre--wired and pre--charged with Puron
R
(R--410A) HFC refrigerant. The units are factory tested in
both heating and cooling modes. These units meet the
ASHRAE 90.1--2007 efficiency levels.
STANDARD FEATURES
Base Unit
S Puron (R--410A) HFC refrigerant
S SEER’s up to 13.0 (04--06 sizes)
S EER’s up to 11.0
S IEER 11.2 (07 size only)
S Rated in accordance with AHRI Standards 210/240
(04--06 sizes) and 340/360 (07size)
S Designed in accordance with Underwriters’
Laboratories Std 1995
S Listed by UL & CUL--Canada or ETL & ETL--Canada
S Single--stage cooling capacity control
S Non--corrosive composite sloping design; side or center
drain condensate pan. Meets ASHRAE Standard 62
S Standard cooling operating range from 40_Fupto
115_F(4_Cupto46_C). Field installable accessory
extends the minimum down to --20_F(--29_C)
S Field convertible from vertical to horizontal airflow for
slab mounting — No special kits required
S Two--inch disposable return air filters
S Thru--the--bottom power and gas entry capability
S Single point gas and electric connections
S 24--volt control circuit protected with resettable circuit
breaker
S Belt drive, constant torque, permanently lubricated
evaporator--fan motor
S Totally enclosed condenser motors with permanently
lubricated bearings
S Low--pressure and high--pressure switches
S Full perimeter base rail with built--in rigging adapters
and fork truck slots
S Central Terminal Board facilitating simple safety circuit
troubleshooting and simplified control box arrangement
Cabinet
S Access panels with easy grip handles
S Innovative, easy starting, no--strip screw feature on unit
access panels
S Pre--painted exterior panels and primer--coated interior
panels tested to 500 hours salt spray protection
S Fully insulated cabinet
S Tool--less filter access door
Refrigerant System
S Acutrolt refrigerant metering system
S Liquid line filter drier
S Scroll compressors with internal line--break overload
protection
S Copper tube, aluminum fin coils with optional corrosion
resistant coils. Corrosion resistant coils are not available
for single phase (--J voltage) models.
S Removable gauge line plugs for reading refrigerant
pressure with unit panels in place
2
STANDARD FEATURES (cont.)
Gas Heat
S IGC solid--state gas heat exchanger control for on--board
diagnostics, anti--cycle protection, LED error code
designation, burner control logic and energy saving
indoor fan motor delay
S Dedicated 3--5 ton “Low NOx” models available that
meet California Air Quality Management NOx
requirement of 40 nangrams/joule or less. Low NOx
models include stainless steel heat exchangers
S Gas efficiencies up to 82%
S Inducted draft combustion
S Redundant gas valve, with 2 states of heating
S Flame roll--out safety protector
S Solid--state electronic direct spark ignition system
Standard Parts Warranty
S 15--year gas heat exchanger parts -- Stainless Steel
S 10--year gas heat exchanger parts -- Aluminized
S 5--year compressor parts
S 1--year parts
PERFORMANCE DATA
Unit Operating Weight lb
Cooling
Gross Total Capacity: Btuh
at Condenser Air Temperature _F
Gross Sensible Capacity: Btuh
Compressor Power Input: kW
Indoor Entering db _Fwb _F
Airflow CFM External Static Pressure in.wg
Indoor Fan Motor Size Hp
Exhaust Fan Motor Size Hp
Curb Weight lb
Heating
Heating Capacity:
Stage 1 Btuh
Stage 2 Btuh
Heating Capacity Total Btuh
Stage 1 kW
Stage 2 kW
Heating Capacity Total kW
ELECTRICAL DATA
Power Supply to Unit Volts Phase Hz
Minimum Circuit Amps Maximum Overcurrent Protection
SUBMITTAL DATA
Job Name
Architect
Engineer
Contractor
Unit Designation
580J
3
FACTORY--INSTALLED OPTIONS (FIOPs)
j Economizer with DRY BULB sensing and barometric
relief*
Standard Air Leak Dampers —
f Models with W7212 controller provides standard
non--diagnostic control. EconoMi$er IV.
f Models with W7220 controller meets California
Title 24 (section 120.2) Fault Detection and
Diagnostic (FDD) requirements. EconoMi$er X.
f Models with RTU Open controller meets California
Title 24 (section 120.2) Fault Detection and
Diagnostic (FDD) requirements. EconoMi$er 2.
j Economizer with E
NTHALPY sensing and barometric
relief*
Standard Air Leak Dampers —
f Models with W7212 controller provides standard
non--diagnostic control. EconoMi$er IV.
f Models with W7220 controller meets California
Title 24 (section 120.2) Fault Detection and
Diagnostic (FDD) requirements. EconoMi$er X.
f Models with RTU Open controller meets California
Title 24 (section 120.2) Fault Detection and
Diagnostic (FDD) requirements. EconoMi$er 2.
j Economizer with D
RY BULB sensing and barometric
relief*
ULTRA LOW LEAK Air Dampers —
f Models with W7220 controller meets California
Title 24 (section 120.2) Fault Detection and
Diagnostic (FDD) requirements, has return, outside
air and relief damper leakage that meets Title 24
(section 140.4 and ASHRAE 90.1) requirements --
plus 5 year limited parts warranty. EconoMi$er X.
f Models with RTU Open controller meets California
Title 24 (section 120.2) Fault Detection and
Diagnostic (FDD) requirements, has return, outside
air and relief damper leakage that meets Title 24
(section 140.4 and ASHRAE 90.1) requirements --
plus 5 year limited parts warranty. EconoMi$er 2.
j Economizer with E
NTHALPY sensing and barometric
relief*
ULTRA LOW LEAK Air Dampers —
f Models with W7220 controller meets California
Title 24 (section 120.2) Fault Detection and
Diagnostic (FDD) requirements, has return, outside
air and relief damper leakage that meets Title 24
(section 140.4 and ASHRAE 90.1) requirements --
plus 5 year limited parts warranty. EconoMi$er X.
f Models with RTU Open controller meets California
Title 24 (section 120.2) Fault Detection and
Diagnostic (FDD) requirements, has return, outside
air and relief damper leakage that meets Title 24
(section 140.4 and ASHRAE 90.1) requirements --
plus 5 year limited parts warranty. EconoMi$er 2.
j RTU Open multi--protocol controller communicates to
LON, MODBUS, BACNET and Johnson N2 protocols.
j Through the base connectors for gas and electric
conduit/piping
j Stainless steel gas heat exchanger (includes tubes,
vestibule plate and collector box)
j Perfect Humidityt dehumidification system*
j 2 position motorized outdoor air damper*
j Non--fused disconnect
j Powered 115--volt convenience outlet*
j Non--powered 115--volt convenience outlet
j High static evaporator fan motor
j Return Air smoke detector
j Supply Air smoke detector
j CO
2
sensor
j Condenser hail guard -- louvered style*
j Special coating protection for evaporator
and condenser coils*
* Not available for single phase (--J voltage) models.
OPTIONAL WARRANTIES
j Complete Unit Parts only up to 5 years
j Complete Unit Parts and Labor up to 5 years
Many other optional warranties are available.
See the Commercial Start--Up and Optional Extended
Warranty Price price pages for further information.
580J
4
FIELD INSTALLED ACCESSORIES
j Economizer with DRY BULB sensing and barometric
relief
Standard Air Leak Dampers —
f Models with W7212 controller provides standard
non--diagnostic control. EconoMi$er IV.
f Models with W7220 controller meets California
Title 24 (section 120.2) Fault Detection and
Diagnostic (FDD) requirements. EconoMi$er X.
f Models with RTU Open controller meets California
Title 24 (section 120.2) Fault Detection and
Diagnostic (FDD) requirements. EconoMi$er 2.
j Economizer with E
NTHALPY sensing and barometric
relief
Standard Air Leak Dampers —
f Models with W7212 controller provides standard
non--diagnostic control. EconoMi$er IV.
f Models with W7220 controller meets California
Title 24 (section 120.2) Fault Detection and
Diagnostic (FDD) requirements. EconoMi$er X.
f Models with RTU Open controller meets California
Title 24 (section 120.2) Fault Detection and
Diagnostic (FDD) requirements. EconoMi$er 2.
j Economizer with D
RY BULB sensing and barometric
relief
ULTRA LOW LEAK Air Dampers —
f Models with W7220 controller meets California
Title 24 (section 120.2) Fault Detection and
Diagnostic (FDD) requirements, has return, outside
air and relief damper leakage that meets Title 24
(section 140.4 and ASHRAE 90.1) requirements.
EconoMi$er X.
f Models with RTU Open controller meets California
Title 24 (section 120.2) Fault Detection and
Diagnostic (FDD) requirements, has return, outside
air and relief damper leakage that meets Title 24
(section 140.4 and ASHRAE 90.1) requirements.
EconoMi$er 2.
j Economizer with E
NTHALPY sensing and barometric
relief
ULTRA LOW LEAK Air Dampers —
f Models with W7220 controller meets California
Title 24 (section 120.2) Fault Detection and
Diagnostic (FDD) requirements, has return, outside
air and relief damper leakage that meets Title 24
(section 140.4 and ASHRAE 90.1) requirements.
EconoMi$er X.
f Models with RTU Open controller meets California
Title 24 (section 120.2) Fault Detection and
Diagnostic (FDD) requirements, has return, outside
air and relief damper leakage that meets Title 24
(section 140.4 and ASHRAE 90.1) requirements.
EconoMi$er 2.
j Power exhaust -- prop fan design
j Two--position motorized outdoor air damper
j Manual outside air damper 25%
j Manual outside air damper 50%
j Roofcurb -- 14 inch (356mm) tall
j Roofcurb -- 24 inch (610mm) tall
j Thru--the--bottom connections--electrical only
j Thru--the--bottom connections--electrical and gas
j Condenser hail guard -- louvered style
j Flue shield
j Flue discharge deflector
j Liquid propane (LP) conversion kit
j High altitude conversion kit
j Phase monitor (loss of phase/phase reversal)
j Winter start kit, down to 25_F(--4_C)
j Fan/Filter status switch
j Low ambient head pressure controller,
downto0_F(--18_C)
j Low ambient head pressure controller,
down to --20_F(--29_C)
j Time Guard II compressor anti--cycle protection
j Return Air smoke detector
j Supply Air smoke detector
j Thermostats and Sensors
Economizer Sensors
j Single Dry bulb control
j Differential Dry bulb control
j Single enthalpy control
j Differential enthalpy control
j CO
2
-- wall mounted
j CO
2
-- duct mounted
j CO
2
-- unit mounted
580J
5
CERTIFIED DIMENSION 580J*04--07
C08039
580J
6
CERTIFIED DIMENSION 580J*04--07
C08040
580J
7
ROOF CURB DETAILS
E
E
7/16"
[11]
4 9/16"
[115.5]
1/4"
[7.0]
5' 7-3/8"
[1711.3]
1' 4-13/16"
[427] INSIDE
1-3/4"
[44.4]
2-3/8"
[61]
1-3/4"
[44.5]
1.00"
[25.4]
"A"
1-3/4"
[44.4]
21.74"
[552.2]
5.42"
[137.7]
11.96"
[303.8]
4.96"
[126.0]
70.87"
[1800.2]
40.69"
[1033.5]
21.84"
[554.7]
16.03"
[407.2]
1.75"
[44.5]
20.41"
[518.3]
3.00"
[76.2]
13.78"
[350.0]
14.00"
[355.6]
3.00"
[76.2]
15.19"
[385.8]
32.19"
[817.6]
3'-1 3/16"
[944.6]
"A"
1-3/4"
[44.5]
CRBTMPWR001A01 3/4" [19] NPT
3/4" [19] NPT
1/2" [12.7] NPTCRRFCURB002A01
CONNECTOR PKG. ACC. GAS CONNECTION TYPE GAS FITTING
POWER WIRING
FITTING
CONTROL WIRING
FITTING
ACCESSORY CONVENIENCE
OUTLET WIRING CONNECTOR
THRU THE CURB
1/2" [12.7] NPT 1/2" [12.7] NPT
CRBTMPWR003A01 THRU THE BOTTOM
ROOF CURB
ACCESSORY #
A
CRRFCURB001A01
14"
[356]
24"
[610]
ECN NO.APP'DCHK'DBYDATEREVISION RECORDREV
1067898--MMC04/22/13
OVERALL DIM. 5'-7 3/8" WAS 5'-7 7/8; 18GA
MATERIAL WA 16 GA.; NAIL FIELD SUPPLIED WAS
WITH CURB
A
DRAWING RELEASE LEVEL:
PRODUCTION
THIRD ANGLE
PROJECTION
UNLESS OTHERWISE SPECIFIED
DIMENSIONS ARE IN INCHES
TOLERANCES ON:
THIS DOCUMENT AND THE INFORMATION CONTAINED THEREIN
IS PROPRIETARY TO CARRIER CORPORATION AND SHALL NOT
BE USED OR DISCLOSED TO OTHERS, IN WHOLE OR IN PART,
WITHOUT THE WRITTEN AUTHORIZATION OF CARRIER CORPORATION.
1 DEC 2 DEC 3 DEC ANG
MATERIAL
----
-
-
-
AUTHORIZATION NUMBER TITLE
1041738
CURB ASY, ROOF
ENGINEERING MANUFACTURING
(004-007)
ENGINEERING REQUIREMENTS
-
-
-
-
SIZE DRAWING NUMBER REV
T-005, Y-002
DRAFTER CHECKER
D
48TC400427
B
WEIGHT:
-
MMC 06/17/11 - -
SHEET 5 OF 5
SURFACE FINISH MFG/PURCH MODEL (INTERNAL USE ONLY) NEXT DRAWING SCALE DISTRIBUTION
- PURCH - N/A MMC
NOTES:
1. ROOFCURB ACCESSORY IS SHIPPED DISASSEMBLED.
2. INSULATED PANELS: 25.4 [1"] THK. POLYURETHANE FOAM, 44.5 [1-3/4] # DENSITY.
3. DIMENSIONS IN [ ] ARE IN MILLIMETERS.
4. ROOFCURB: 18 GAGE STEEL.
5. ATTACH DUCTWORK TO CURB. (FLANGES OF DUCT REST ON CURB).
6. SERVICE CLEARANCE 4 FEET ON EACH SIDE.
7. DIRECTION OF AIR FLOW.
8. CONNECTOR PACKAGE CRBTMPWR001A01 IS FOR THRU-THE-CURB GAS TYPE
PACKAGE CRBTMPWR003A01 IS FOR THRU-THE-BOTTOM TYPE GAS CONNECTIONS.
TYPICAL (4) SIDES
SUPPLY AIR RETURN AIR
ROOFING MATERIAL
(FIELD SUPPLIED)
CANT STRIP
(FIELD SUPPLIED)
ROOFING FELT
(FIELD SUPPLIED)
COUNTER FLASHING
(FIELD SUPPLIED)
UNIT
GASKET
(SUPPLIED WITH CURB)
RIGID INSULATION
(FIELD SUPPLIED)
DUCT
(FIELD SUPPLIED)
NAIL (FIELD SUPPLIED)
CERTIFIED DRAWING
VIEW "B"
CORNER DETAIL
SEE VIEW "B"
RETURN AIR
SUPPLY AIR
SUPPLY AIR
OPENING
RETURN AIR
OPENING
GAS SERVICE PLATE
THRU THE CURB
DRILL HOLE
2" [50.8] @
ASSEMBLY (IF
REQUIRED)
(SEE NOTE #8)
SEE NOTE #2
11 3/4"[298.5] WIDE
INSULATED DECK PANELS
8 9/16"[217.5] WIDE
INSULATED DECK PANEL
1/3/4"[44.5]
SCALE 0.250
E-ESECTION
C13310
580J
8
Manufacturer reserves the right to discontinue, or change at any ti me, specifications or designs without notice and without incurring obligations.
E2014 Bryant Heating & Coo li ng Systems D 7310 W. Morri s St. D Indianapolis, IN 46231 Edition Date: 06/14
Replaces: SUB580J--- 13
Catalog No. SUB580J---4---7---01
580J
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8

Bryant LEGACY 580J Submittal Data

Bryant
Brand
Bryant
Model
LEGACY 580J
Category
Split-system air conditioners
Type
Submittal Data

Bryant LEGACY 580J is a single-packaged electric cooling, gas heating unit pre-wired and pre-charged with PuronR (R--410A) HFC refrigerant. The unit is factory tested in both heating and cooling modes and meets ASHRAE 90.1-2007 efficiency levels. It features:

  • SEER’s up to 13.0 (04-- 06 sizes)
  • EER’s up to 11.0
  • IEER 11.2 (07 size only)
  • Non-corrosive composite sloping design; side or center drain condensate pan. Meets ASHRAE Standard 62
  • Standard cooling operating range from 40_F up to 115_F (4_C up to 46_C). Field installable accessory extends the minimum down to - 20_F (-- 29_C
Download PDF
report

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI

Related papers

Other documents