GPS 5 panel
USER MANUAL
(MEO2.520-27MAY2010)
1
Please read this manual before operating your
units and keep it for future reference.
All stated here is subject to change without advanced notice for improvement.
Tel : +82-31-284-7090~91 Fax : +82-31-284-7092 E-mail : [email protected] Web site : www.vrinsight.com
Virtual Reality Insight
VRinsight
BEFORE USE : Thanks for purchasing VRi’s GPS-5.
Before operating your units, please read through this manual and keep it for future
reference.
For any further question, visit www.wilcopub.com or contact us below:
Fax : +32-2-33107 51
E-mail (Support team) : info@wilcopub.com
NOTE : This manual could be redistributed unless you modify the contents.
This manual has been written out on a Serial FP v2/Jet Liner’s GPS-5 basis.
All software (& software versions) stated here (MEO2.520-16APR2010) is
Subject to change without advanced notice for improvement.
If you want to download the latest driver version for panel & application
programs, visit www.vrinsight.com
2
programs, visit www.vrinsight.com
VRinsight GPS-5
3
The GPS-5 of VRinsight features Control Display Unit for providing terrain
information and for warning terrain hazard of potential conflicts. It is the most
fundamental approach guide into the airports inaccessible in IFR conditions.
Real shape & full functionality of GPS-5 supports all default aircrafts & add-on
aircrafts. It is completely interfaced with MSFS9 and MSFSX through
interfacing application software “SerialFP2” (supplied).
Requires USB 2.0 port , unregistered FSUIPC and a free DVI or VGA port
•Standalone type
•SerialFP2 software supports all functions to GPS-5.
• If you want to use a USB hub, be sure that the USB hub is USB 2.0 compliant.
Otherwise it may cause a malfunction.
• Available in Window mode only.
Features
• Realistically shaped and fully functional buttons, dual knob and LCD
• LCD size : 15cm (L) X 8.8cm (W) / 7 inch
• Fully metal cases
• Standalone type
• Available in Window mode only
• One year warranty
Technical specifications
• USB interface type to computer
•
External power requirement ; DC 12V adaptor (Included in package)
4
•
External power requirement ; DC 12V adaptor (Included in package)
• Video port requirement : One DVI or VGA video port
• 19 cm (L) x 14 cm (W) x 14 cm (H)
• 1.3Kg
Compatibility software
• Flight Simulator 2004 / FSX by Microsoft
Operating software
• SerialFP2
BEFORE USE
Before use GPS-5, please check below procedures.
SerialFP2 Installation
In the GPS-5 package, one “Install DVD” is included. When you insert it in DVD
driver of your computer, “VRinsight HTML” document will be shown. Then click
“SerialFP2” (operating software) and install it at a proper folder.
“SerialFP2” is the main operating software of VRinsight used for all VRinsight flight
panels.
SerialFP2 software supports all functions of GPS-5 and completely interfaced with
MSFS9 and MSFSX enables full simulation with simple connection your computer
through USB.
Be sure that when installing SerialFP2, “Install USB-Serial Driver” must be checked.
After installation, you can find “SeiralFP2” in “All programs” of “Start menu”.
USB Connection
5
The connection between GPS-5 and your computer is made using a USB cable
that plugs into one USB port on your computer. If you want to use a USB hub, be sure
that the USB hub is USB 2.0 compliant. Otherwise it may cause a malfunction.
When you connect GPS-5 to your computer at first, your computer will detect it and
will describe the process step by step.
Power Connection
Power supplying of GPS-5 panel is done by universal power supply adaptor DC
12V (Included in package).
Video Connection
The connection between GPS-5 and your computer is made using DVI or VGA
cable.
Run “SerialFP2”
When you confirm all setup processes done; “SerialFP2” installation, “USB
connection”, “Video Connect” and “Power connection”, you are ready to operate
GPS-5.
Double click the shortcut of “SerialFP2” or find it in “All programs” of “Start menu .
If everything is done properly, below window will be shown.
6
1. Check the current display properties in order that another sub monitor is
connected or not. (See “Settings”)
Monitor setting
7
2. Connect video cable of GPS-5 to your computer.
3. Connect AC/DC adaptor to your GPS-5.
4. Check the display properties in order that GPS-5 monitor is detected or not.
* If the GPS-5 monitor (=Monitor 2) isn’t detected, check the connection of video
cable & AC/DC adaptor.
* If your OS is VISTA, please restart your computer.
5. When the GPS-5 monitor is recognized, click monitor 2(=GPS-5 monitor).
6. Adjust the resolution for GPS-5 monitor.
(Recommended resolution is 1280 * 768).
7. Check the position of the monitor 2 :
8
8. Move the monitor 2 to the left side of monitor 1 (important)
9. Check “Extend my Windows desktop onto this monitor”.
* If GPS-5 monitor doesn’t illuminate, restart your computer.
10. Click “Apply” and click “OK”
11. If everything is done properly, GPS-5 will be power on.
12. Multiple display & Monitor rotation setting
12-A. NVIDIA
12-A-1. Launch “NVIDIA Control Panel”.
12-A-2. Go to “Set up multiple displays and check “Configured independently
from each other (
Dualview
). Then the monitor of GPS
-
5 will independently
9
from each other (
Dualview
). Then the monitor of GPS
-
5 will independently
display your “Desktop” view.
12-B. ATI
12-B-1. Launch “Catalyst(TM) Control Center”.
The monitor of GPS-5 will automatically display your “Desktop” view.
12-B-2. Go to “Displays Properties” and select monitor 2.
10
GPS-5 controls explanation
11
Buttons : Buttons are used to input & assign the data and enter the pages
LCD display : Shows all information about GPS-5
Buttons : Programmable button
Dual knob : Input alphabet & number
MENU
Displays a context-sensitive list of options. This options list
allows the pilot to access additional features or make settings
changes which relate to the currently displayed page.
CLR
Used to erase information, remove map detail, or to cancel an
entry. Press and hold the CLR Key to immediately display the
Default NAV Page
ENT
Used to approve an operation or complete data entry. It is
also used to confirm information during power on
RNG+
Allows the pilot to select the desired map
range. Use the up arrow to zoom out to a larger area, or
the down arrow to zoom in to a smaller area
RNG-
DIR
Provides access to the direct-to function, which allows the
pilot to enter a destination waypoint and establishes a direct
course to the selected Destination.
12
ENT
NRST
OBS
MSG
also used to confirm information during power on
The NRST Key displays the Nearest Airports Page. Then,
turning the small right knob steps through the NRST pages
Used to select manual or automatic sequencing of
waypoints. Pressing the OBS Key selects OBS mode, which
retains the current ‘active to’ waypoint as the navigation
reference even after passing the waypoint (i.e., prevents
sequencing to the next waypoint). Pressing the OBS Key
again returns the unit to normal operation, with automatic
sequencing of waypoints. When OBS mode is selected, the
pilot may set the desired course to/from a waypoint using
the Select OBS Course pop-up window, or an external OBS
selector on the HSI or CDI.
Used to view system messages and to alert the pilot to
important warnings and requirements
FPL
Allows the pilot to create, edit, activate, and invert flight plans,
as well as access approaches, departures, and arrivals. A
closest point to flight plan feature is also available from the
FPL Key
TERR
Used to select pages within one of the page groups. Press
this knob momentarily to display the on-screen cursor. The
cursor allows the pilot to enter data and/or make a selection
from a list of options. When entering data, the small right
knob is used to select the desired letter or number and the
large right knob is used to move to the next character space.
The small right knob is also used to move the target pointer
up (turn clockwise) or down (counterclockwise) when the
map panning function is active.
Allows the pilot to create a three-dimensional profile which
provides guidance to a final (target) altitude at a specified
location
Allows the pilot to select and remove
approaches, departures, and arrivals from the flight plan.
When using a flight plan, available procedures for the
departure and/or arrival airport are offered automatically.
Otherwise, the pilot may select the desired airport, then
the desired procedure
PROC
13
Used to select page groups: NAV,WPT, AUX, or NRST. With
the on-screen cursor enabled, the large right knob allows the
pilot to move the cursor about the page. The large right knob
is also used to move the target pointer right (turn clockwise)
or left (counterclockwise) when the map panning function is
active.
User programmable
Panel installer launch
: Panel installer will copy & paste all necessary panel data to work GPS-5
automatically. Be sure “Panel Installer” should run before running SerialFP2.
* Once the panel is installed, aircraft configuration is kept.
After “SerialFP2” installation, you can find “Panel Installer”.
14
How to use “Panel Installer”.
A. Run “Panel Installer” first
1. MSFS-Root Path : Browse the path where “Flight Simulator 9” or “Microsoft Flight
Simulator X” is installed.
* If “Flight Simulator 9” or “Microsoft Flight Simulator X” is installed other “Drive” or
“Directory”, find the path and click “OK”.
1
2 3 4
5
15
* if you select a wrong path, “Status” window displays error message.
2. VRinsight panel : Drop down and select your panel.
3. Aircraft : Drop down and select your aircraft.
16
4. Run : Copy & paste all necessary panel data to work GPS-5 automatically.
* If you select an aircraft for FS9 and the “MSFS-Root Path” is for FSX, “Status”
window displays error message and all necessary panel date will not be
automatically copied & pasted. And vice versa.
5. Status : Inform current status.
* If everything is done properly, you will get below message
17
Preparing GPS-5 before Flight (With Cessna 172)
Step 1 : Initial check up
Before flight with GPS-5, please check the followings are done
A. Install of SerialFP2.
* Check that “Install USB-Serial Driver” is checked or not.
B. Confirm the USB connection.
* Check that the USB port of your computer is dead or not
* Check that if you use USB hub, be sure that the USB hub is USB 2.0 compliant.
C. Confirm DC 12V adaptor is plugged in.
D. Confirm the DVI or VGA connection.
E Confirm the monitor setting. (See page no. 7)
F. Confirm that “Panel Installer” is executed or not.
Step 2 : Run flight simulator (MSFS9 / MSFSX)
A. Run flight simulator (MSFS9 / MSFSX).
B. Select Cessna 172.
18
Step 3 : Click “Views” => “Instrument Panel” => GPS.
When “GPS” window is shown, undock it.
Step 4 : Run panel linking application software “SerialFP2”.
19
1 : Number of COM(USB) port
2 : Type of panel
3 : Firmware version
4 : Aircraft selection
5 : Link to game
6 : Software loading sequence change
Original sequence
(MSFS loading first => SerialFP2 running)
New sequence
(MSFS loading / SerailFP2 running first
=> Serial FP2 running / MSFS loading)
7 : Input test for panel
8 :Link test for panel with game
1 2 3
4
5
6
78
Step 5. Press “Load FS Module” to move undocked GPS display to GPS-5.
Step 6. Input the X & Y position and size of GPS-5 monitor and press “Redraw”.
Step 7. Confirm the GPS display has been moved to GPS-5. Then press “Save” for
future purpose. With “Panel Config” window, you can adjust position and size of the
display. See how to control them.
* For instance,
If X & Y position is
same as page 8,
Put X=1680, Y=0.
If X & Y size is same as
page 8, Put W=768,
Y=1280.
20
Page is loading ...
-
1
-
2
-
3
-
4
-
5
-
6
-
7
-
8
-
9
-
10
-
11
-
12
-
13
-
14
-
15
-
16
-
17
-
18
-
19
-
20
-
21
Ask a question and I''ll find the answer in the document
Finding information in a document is now easier with AI
Other documents
-
Garmin GNS 480 User guide
-
Garmin G1000 - Cessna 182T/T182T/J182T Nav III Reference guide
-
-
-
-
Apollo CNX80 User manual
-
-
-
-
Garmin G1000 NXi - Cessna 172R/172S Nav III Reference guide