2. Gamber-Johnson
  3. 7170-0822-02

Gamber-Johnson 7170-0822-02, 2020+ Ford Police Interceptor Utility Full Depth Console Kit with Center Mount, Armrest and Cup Holder, 2020+ Ford Police Interceptor Utility Full Depth Console Kit with Printer Insert, Side Mount, Armrest, and Cup Holder, 2020+ Ford Police Interceptor Utility Full Depth Console Kit with Printer Insert, Side Mount, Armrest, Cup Holder, and Mongoose- 9" Locking Slide Arm, 2020+ Ford Police Interceptor Utility Full Depth Console Kit with Printer Insert, Side Mount, Armrest, Cup Holder, and Mongoose- 9" Locking Slide Arm with Short Clevis, 2020+ Ford Police Interceptor Utility Full Depth Console Kit with Side Mount, Armrest, and Cup Holder, 7170-0822-00, 7170-0822-01, 7170-0822-03, 7170-0822-04 Installation guide

  • Hello! I am an AI chatbot trained to assist you with the Gamber-Johnson 7170-0822-02 Installation guide. I’ve already reviewed the document and can help you find the information you need or explain it in simple terms. Just ask your questions, and providing more details will help me assist you more effectively!
A
INST-970
7170-0822-01 KIT
CENTER MOUNT
7170-0822-00 KIT
SIDE MOUNT
CONSOLE KIT - 2020+ FORD PI UTILITY, FULL DEPTH
Printing Spec:
PS-001
© Copyright 2020 Gamber-Johnson, LLC
1/4
7170-0822-00
7170-0822-01
OEM USB/12V
RELOCATION
If you need assistance or have questions, call Gamber-Johnson at 1-800-456-6868
Form
Revision
Product
INSTALLATION INSTRUCTIONS
Product Mounting Disclaimer
Gamber-Johnson is not liable under any theory of contract or tort law for any loss, damage, personal injury, special, incidental or consequential damages for personal injury or other damage
of any nature arising directly or indirectly as a result of the improper installation or use of its products in vehicle or any other application. In order to safely install and use Gamber-Johnson
products full consideration of vehicle occupants, vehicle systems (i.e., the location of fuel lines, brake lines, electrical, drive train or other systems), air-bags and other safety equipment is
required. Gamber-Johnson specifically disclaims any responsibility for the improper use or installation of its products not consistent with original vehicle manufactures specifications
and recommendations, Gamber-Johnson product instruction sheets, or workmanship standards as endorsed through the Gamber-Johnson Certified Installer Program.
2/4
3. With the OEM controller removed reinstall the trim back in place.
run the wires through the opennings
Figure 2
Figure 1
Installation:
1. Remove the OEM Center console
by loosen the 4 nuts using 10MM
socket.(shown in figure 1)
2. Remove the OEM center trim by
loosen the 2 bolts holding it using
7MM socket. Remove the OEM
12v/USB/E-brake from the Trim, (to
remove the E-brake use T20
socket.)
4. With the OEM trim removed, place the 2
front leg of the full depth console in the
OEM stud as shown. (yellow arrow)
Figure 3
Figure 4
5. With the front legs installed, then drop the main
console over the legs. (the legs stay on the inside
of the console). The rear legs mounts to the rear
OEM stud (yellow arrow). then the front leg can be
attached to the console with 1/4-20 allen head
bolts.
*If vehicle is equipped with OEM rear wire tunnel it
can be directly attached to the console (black
arrow) with provided 1/4-20 hardware.
3/4
SIDE MOUNT
BRACKET
COVER PLATE
TOP PLATE
PARKING BRAKE
BRACKET
TOP PLATE
COVER PLATE
LOWER TUBE
Side Mount (7170-0822-00)
Install the parking brake switch to the side of the console first
1.
Then install the top plate over the lower pole
2.
Install equipment as needed, then attached the cover plate
3.
Install the Side mount bracket if needed for motion device
4.
Center Mount (7170-0822-01)
Install the parking brake switch to the side of the console first
1.
Install the lower pole on to the console center beam
2.
Then install the top plate over the lower pole
3.
Install equipment as needed, then attached the cover plate.
4.
For motion device attach the upper pole to the lower tube.
5.
4/4
/