Unbranded 0011 User guide

Unbranded
Brand
Unbranded
Model
0011
Type
User guide

This manual is also suitable for

21.25”
7.125”
1/2” NO PRINTING AREA
.5”
OVERALL DIMENSION: 7 1/8” X 21 1/4”
NO PRINTING AREA OF 1/2” TO ACCOMMODATE GLUE AREA OF LABEL
GLUE LAP CAN BE ON EITHER END OF LABEL. DIFFERENT MACHINES USE DIFFERENT POSITIONS
EAR HOLES ARE 1 3/8” IN DIAMETER. THEY ARE 10 1/4” APART, ON CENTER.
IT IS BETWEEN THESE TWO HOLES THAT THE FRONT OF LABEL USUALLY FALLS.
DIRECTIONS COPY GOES HERE
FRONT COPY GOES HERE
10.25”
10.25”
7”
THIS TEMPLATE IS A GUIDE ONLY. YOUR ARTWORK SHOULD BE
COMPOSED TO FIT THE ACTUAL CAN YOU ARE FILLING AND THE
EQUIPMENT IT IS BEING APPLIED WITH.
1 GALLON COVERS APPROX. 325 SQ. FT. WWW.WEATHERWASHCOATIN GS.COM
WOOD PREP
Surface must be free of sealers, stains, & conditioners
before staining. Prepare wood for staining by sanding with 80 grit
sandpaper with the grain.
PRODUCT PREP
MIX STAIN WELL before and during use to ensure
settled materials are re-dispersed. Do not thin. First, TEST an
INCONSPICUOUS SWATCH. For best results, store and use only
when temperature is between 60-90°F (16-32°C) and relative
humidity is below 85%. Do not store in metal containers.
COVERAGE
1 gallon treats 325 sq. ft. of smooth wood.
APPLICATION
Use a foam roller, rag, brush, or paint sprayer to
apply one liberal coat of stain in the direction of the grain. Wood
will absorb stain and each species will turn its own darkest color.
D o N O T apply an d w ipe off. DR EN C H the wo od evenl y to ens ure
consistent color. For exteriors, MIST may be applied on site and
w ill n ot affe
c
t groun d or pl ant life. Ho w ever, it ma y s tain
exposed concrete or siding.
DRYIN G TIM E
Allow wood to dry 60 minutes. Longer dry times
for damp / humid climates, rough sawn & soft woods.
CLEAN UP
Easy soap and water clean up.
FIN ISHES
After a minimum of 1 hour apply your favorite
Weatherwash topcoat per the directions on the can.
CAUTION S
Do not take internally. Keep out of reach of children.
In cas e of eye con tact flus h wi th large am oun ts of w ater.
Get medical attention if irritation persists. If swallowed do
not induce vomiting. Get medical attention immediately.
Why waste hours applying primers, paints, and glazes
when you can actually age wood? Weatherwash MIST
is a tannin-based, reactive stain, which naturally ages
wood in minutes. Woods that are high in tannic acid
will yield a lightly aged look in minutes instead of
centuries. Color results depend on wood species and
will create a natural-looking result without compromising
the grain. Weatherwash MIST can be top-coated
and will maintain color consistency.
AGE IN DEX
Use for a lightly weathered look.
SPECIES
H igh tan nin w oods like cedar, douglas fir
,
redw o od,
locust, and walnut. See our color chart online.
USE
For us e on w ood w alls , ceilin gs , floors , cabin etry, furn iture,
millwork, siding, fences, etc.
Water-Based
Top Coat Compatible
VOC Free
Non Toxic
Commercial & Residential
Interior & Exterior
WARNING!
Rem oval of old pain t by s an din g, s craping or other m eans m ay gen erate dus t or fum es that contain lead.
Expos ure to lead dus t or fum es m ay caus e brain dam age or other advers e health effec ts, es pecially in children or
pregnant women. Controlling exposure to lead or other hazardous substances requires the use of proper protective
equipm en t s uch as a properly fit
t
ed res pirator (NI OS H approved) and proper con tain m en t and clean up. For m ore
information, call the National Lead Information Center at 1-800-424-LEAD (in US) or contact your local health authority.
21.25”
7.125”
1/2” NO PRINTING AREA
.5”
OVERALL DIMENSION: 7 1/8” X 21 1/4”
NO PRINTING AREA OF 1/2” TO ACCOMMODATE GLUE AREA OF LABEL
GLUE LAP CAN BE ON EITHER END OF LABEL. DIFFERENT MACHINES USE DIFFERENT POSITIONS
EAR HOLES ARE 1 3/8” IN DIAMETER. THEY ARE 10 1/4” APART, ON CENTER.
IT IS BETWEEN THESE TWO HOLES THAT THE FRONT OF LABEL USUALLY FALLS.
DIRECTIONS COPY GOES HERE
FRONT COPY GOES HERE
10.25”
10.25”
7”
THIS TEMPLATE IS A GUIDE ONLY. YOUR ARTWORK SHOULD BE
COMPOSED TO FIT THE ACTUAL CAN YOU ARE FILLING AND THE
EQUIPMENT IT IS BEING APPLIED WITH.
1 GALLON COVERS APPROX. 325 SQ. FT. WWW.WEATHERWASHCOATIN GS.COM
WOOD PREP
Surface must be free of sealers, stains, & conditioners
before staining. Prepare wood for staining by sanding with 80 grit
sandpaper with the grain.
PRODUCT PREP
MIX STAIN WELL before and during use to ensure
settled materials are re-dispersed. Do not thin. First, TEST an
INCONSPICUOUS SWATCH. For best results, store and use only
when temperature is between 60-90°F (16-32°C) and relative
humidity is below 85%. Do not store in metal containers.
COVERAGE
1 gallon treats 325 sq. ft. of smooth wood.
APPLICATION
Use a foam roller, rag, brush, or paint sprayer to
apply one liberal coat of stain in the direction of the grain. Wood
will absorb stain and each species will turn its own darkest color.
D o N O T apply an d w ipe off. DR EN C H the wo od evenl y to en s ure
consistent color. For exteriors, MIST may be applied on site and
w ill n ot affe
c
t groun d or pl ant life. Ho w ever, it ma y s tain
exposed concrete or siding.
DRYIN G TIM E
Allow wood to dry 60 minutes. Longer dry times
for damp / humid climates, rough sawn & soft woods.
CLEAN UP
Easy soap and water clean up.
FIN ISHES
After a minimum of 1 hour apply your favorite
Weatherwash topcoat per the directions on the can.
CAUTION S
Do not take internally. Keep out of reach of children.
In cas e of eye con tact flus h wi th large am oun ts of w ater.
Get medical attention if irritation persists. If swallowed do
not induce vomiting. Get medical attention immediately.
Why waste hours applying primers, paints, and glazes
when you can actually age wood? Weatherwash MIST
is a tannin-based, reactive stain, which naturally ages
wood in minutes. Woods that are high in tannic acid
will yield a lightly aged look in minutes instead of
centuries. Color results depend on wood species and
will create a natural-looking result without compromising
the grain. Weatherwash MIST can be top-coated
and will maintain color consistency.
AGE IN DEX
Use for a lightly weathered look.
SPECIES
H igh tannin w oods like cedar, douglas fir
,
redw o od,
locust, and walnut. See our color chart online.
USE
For us e on w ood w alls , ceilin gs , floors , cabin etry, furn iture,
millwork, siding, fences, etc.
Water-Based
Top Coat Compatible
VOC Free
Non Toxic
Commercial & Residential
Interior & Exterior
WARNING!
Rem oval of old paint by s an ding, s craping or other m ean s m ay gen erate dus t or fum es that contain lead.
Expos ure to lead dus t or fum es m ay caus e brain dam age or other advers e health effec ts, es pecially in children or
pregnant women. Controlling exposure to lead or other hazardous substances requires the use of proper protective
equipm en t s uch as a properly fit
t
ed res pi rator (NI OS H approved) an d proper con tain m en t and clean up. For m ore
information, call the National Lead Information Center at 1-800-424-LEAD (in US) or contact your local health authority.
DIRECTIONS
WEATHERWASH’S “MIST” PRODUCT OVERVIEW
WOOD PREP Sand wood with the grain. Do not apply pretreaters.
PRODUCT PREP Mix stain well before and during use to ensure
settled materials are re-dispersed. Do not thin. First, test and
inconspicuous swatch. For best results, store and use only when
temperature is between 60-90°F (16-32°C) and relative humidity is
below 85%. Do not store in metal containers
COVERAGE 1 Gallon treats 400 sq. ft. of smooth wood.
APPLICATION Use a foam roller, brush or paint sprayer to apply one
liberal coat of stain in the direction of the grain. Wood will absorb
stain. Each species will turns its own darkest color. For exteriors,
stain may be applied on site but avoid contact with concrete or
siding.
DRYING TIME Allow wood to dry 60 minutes. Longer dry times for
damp/humid climates, rough sawn & soft woods.
CLEAN UP Easy soap and water clean up.
FINISHES After a minimum of 1 hour apply your favorite
Weatherwash topcoat per the directions on the can.
Why waste hours applying primers, paints, and glazes when you can age wood in minutes?
Mist is a tannin-based, reactive stain, that naturally ages wood. It is suitable for mid-high tannin
wood types and yields light weathered grays in minutes, instead of centuries. Unlike pigment
based stains, latex paints, or oil-based stains. Mist won’t compromise the wood’s grain. Color
results depend on wood specie is and will create a natural-looking result from plank to plank. Stain
can be top coated to maintain color consistency.
AGE INDEX Lightly Weathered
SPECIES Mid-high tannin woods like cedar, redwood, douglas fir, maple, alder, hickory, locust,
walnut, oak, etc. S Not for use on pine, spruce, poplar, or teak. See our color chart.
USES For interior and exterior use, good for siding, walls, ceilings, floors, millwork, cabinetry,
decks, fences, etc.
MIST STAIN ON VARIOUS WOOD SPECIES
MAPLE HICKORY BIRCH BEECH
DOUG FIR -ROUGH DOUG FIR – SMOOTH RED CEDAR - ROUGH RED CEDAR - SMOOTH
MAPLE ALDER MAHOGANY REDWOD
CHERRY WALNUT LOCUST OAK
  • Page 1 1
  • Page 2 2

Unbranded 0011 User guide

Unbranded
Brand
Unbranded
Model
0011
Type
User guide
This manual is also suitable for
Download PDF
report

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI

Related papers

Other documents