Pacific Entries P2210-24S Installation guide

Brand
Pacific Entries
Model
P2210-24S
Type
Installation guide
Taking Pride in Providing You the Perfect Door Reversible Jamb System
Interior Door: Prehang Kit
Installation Instructions
TOOLS REQUIRED
READ ALL INSTRUCTIONS PRIOR TO STARTING!
- continued -
Shims
Blue Tape
Hammer
Tape
Measure
Level
Wood Glue
Power Drill with
Phillips Head Bit
BEFORE GETTING STARTED: PRECAUTIONS
1. Please wear safety gear appropriate to tools being used. Eye protection should be used at all times. Failure to use
protective eye gear can result in serious injury. ALWAYS wear proper safety gear when operating power tools.
2. Always ensure you have ample space to operate power tools with complete control of the power tool.
3. Door(s) are heavy and should be lifted by 2 people at all times. Mishandling of heavy objects (i.e., doors) may cause a
loss of balance resulting in injury. Always take precaution in assuring proper balance before moving the door(s). Safety
shoes should also be worn to prevent any foot injuries.
5. Door(s) swing on hinges which can create pinch points (hair, fingers, clothing, etc.). Take precaution when swinging.
6. Take care in not catching fingers in door opening when swinging the door closed.
GLUE
page 1 of 2
In addition to the written
instructions on page 2, click
on the QR code to view the
assembly video
rev. 04-13-16
rev. 04-13-16
INSTALLING INTERIOR DOOR: PREHANG KIT
* please read ALL instructions prior to assembling *
1) Determine door handing - Standing on the side you want the door to swing
towards, establish whether hinges will be on left or right side of door (figure 1).
2) With door standing, apply screws in each square side of hinge with pin facing
towards you (figure 2).
3) a. Place door on flat protected work surface (use protective blanket or pad so as to
not scratch) with hinges facing down. Make sure surface is clean of any debris.
Apply hinge jamb with top of jamb (end with pre-drilled screw holes) towards
top of door.
b. Attach head jamb and then strike jamb using provided screws (figure 3). Make
sure install channel lines up with hinge jamb. Careful not to over tighten so as
to avoid splitting the wood.
4) Install door frame into opening:
a. Place frame in the opening.
b. Shim frame in opening centering as close as possible. Wood shim placement
should provide plum and square alignment with even reveal between door and
jambs (figure 4).
c. Either using screws or nail gun, attach hinge jamb side of frame making sure the
screws or nails penetrate thru the shims. Installation screws or nails should be
placed in jamb channel. Jamb should be fastened in close location to the
hinges (figure 5).
d. Secure the head jamb and strike jamb in same fashion.
5) Install wood stops:
a. Once the door and frame are installed, double check operation and reveals for
proper alignment (figure 6).
b. Using a high quality wood glue, apply small amount to head stop, insert in
groove and hold with blue tape until dry (figure 7 and 8). Wipe any excess glue
off immediately with wet cloth.
c. Repeat stop install for side jambs.
d. NOTE - by gluing the stops in, all nails
or screws will be hidden giving the
install a clean look (no filling or
puttying of the installation holes).
Figure 1
Figure 2
Figure 3
Figure 4
Figure 5
Figure 7
Figure 6
radius edge
hinge ange
onto jamb
square edge hinge
ange onto door
edge of door
jamb and door are predrilled
3 screws per side
if needed, ip jamb to
make latch jamb hole
align with door
handle hole
padded work surface
overhead view
conrm
door & jamb
margins
are equal
conrm
dooris square
(diagonals
should be equal)
Figure 8
edge of door
screw or nail in jamb channel
jamb
channel
center
door in
opening
wood
shims
SIDE VIEW FACE VIEW
GLUE
jamb
channel
head stop
SIDE VIEW FACE VIEW
blue
tape
page 2 of 2
rev. 04-13-16
  • Page 1 1
  • Page 2 2

Pacific Entries P2210-24S Installation guide

Brand
Pacific Entries
Model
P2210-24S
Type
Installation guide
Download PDF
report

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI

Other documents