Read through ALL instructions before commencing
assembly. If you have any questions about this
product or issues with assembly contact the
customer services help line before returning
this product to the store.
STOP
Retain all packaging in case the bracket needs to be returned.
Contents may vary from photography/ Illustrations.
You will not need all these parts, so expect there to be some left over depending upon the
specification of your projector
.
This product is intended for indoor use only. Use of this product outdoors could lead to failure and
personal injury
.
It is the responsibility of the installer to ensure that the mounting surface is of a suitable standard and
void of any services (eg gas, electricity, water etc).
SUPTEK accept no responsibility for any damage or loss caused by installing this product on a sub
standard surface.
Stud Finder
Ø3mm (1/8")
Wood
Ø10mm (25/64")
Masonry
Tools RT ecommended
Boxed Parts
A
1
x1
B
1
x1
C
1
x1
D
2
x4
D
x2
F
x12
E
x4
G
x4
H
x4
25mm
25mm
25mm
25mm
J
x4
K
x4
L
x4
M
x4
M3 M4 M5 M6
4mm
I
x4
B
x4
A
x4
C
x1
Projector Screws
Measure the Projector fixing holes
1
Projector
Fixing Holes
Trous de Fixation
du Projecteur
Huecos de fijación
del proyector
Fixing holes must be within
the shaded area
Max 450mm
Min 72mm
If your Projector fixing holes are not within
the shaded area STOP installation now
and contact the customer help line
!
K
J
M5 =
M4 =
M3 =
L
M6 =
M
You are provided with 4
diameters of Projector
fixing screws,M3,M4,M5
and M6 . Determine the
screw diameter that fits
and remember for step 3.
Configurations are not limited to the examples shown
below . Use the parts supplied in any configuration to
suit your projector.
2
Prepare the Projector Mounting Brack.
Extra Small
Large
Triangular
C1
C1
C1
C1
D2 D2
D2 D2
D2D2
D2
D
2
D
2
D
2
D
2
E
The example shown below is the
medium hole configuration.
F
x4
E
x4
3
Fitting the Projector Mounting Brack.et
WARNING
J M-
G
H
Screw diameter
dependant
If required
I
PR05
J
x4
K
x4
L
x4
M
x4
M3
M4
M5
M6
If required
Attach the bracket to your Projector
using suitable screw reducer and
spacer combinations
I
x4
I
x4
and / or and / or and / or and / or
After completing step 3 you will
have fittings left over please keep
for future reference
!
4
Attach Ceiling Brack et to Extendable Post
D
x2
F
x4
B
1
F
C
A
1
D
If you have chosen not to use the
extendable post A
1
, please ignore
stages 4 and 5.
You will then fit the ceiling bracket as
per stage 6.
!
5
Different Locations
Please see below for examples of dif ferent
Projector mounting locations
Ceiling
Wall
Sloped Ceiling
70mm (
23/4
")
Ø10mm
(25/64")
B
A
Remove dust from hole
Solid Wall
Lubricate screw
thread with soap
Fitting the Ceiling Brack
DO NOT over tighten
screws. Tighten screws
by hand only
!
8mm (5/16")
MAX
6
Please note, the fitting process is exactly the same
if you fit to ceiling, wall or sloping ceiling.
A
x2
B
x2
!
Ø3mm
(1/8")
55mm
(2
1/8
")
A
Lubricate screw
thread with soap
DO NOT over tighten screws.
Tighten screws by hand only
!
Wood Stud
A
x2
Attach the Projector
7
With extendable post
F
C
8
Cable Management
Ensure cables don’t restrict movement
!
i
ii
iii
9
Optional
Tilt and turn
Height adjustable
i
ii
Before loosening, make sure
the projector is fully supported
!
F
x4
C
F
Ensure bracket is in the
centre of the wood stud
-
1
-
2
Ask a question and I''ll find the answer in the document
Finding information in a document is now easier with AI
Other documents
-
AVF ZML8500 User manual
-
AVF NUL401-A Operating instructions
-
-
-
T'nB MCAV4W Datasheet
-
Unimax ZML8351-A Operating instructions
-
Black & Decker FP2650S Datasheet
-
-
Premier MAG-EXT Specification
-
