American DJ LTS-50T User manual

Brand: American DJ

Model: LTS-50T

Type: User manual

American DJ LTS-50T is an affordable and easy-to-assemble lighting trussing system. The system comprises two 5' truss I-beam sections, two 9' tripod stands, and various connectors and T-collars. The LTS-50T has a weight capacity of 200 lbs. and is ideal for mounting lighting fixtures for events, parties, and other applications.

The LTS-50T is easy to assemble, with clear instructions and numbered parts. The system is also adjustable, allowing you to customize the height and width of the truss to suit your needs. The tripod stands provide a stable base for the truss, and the T-collars allow you to attach lighting fixtures securely.

LTS-50T

• 2 x T-bars

• 6 x Slide mount T-collars

• 1 x Center “I-Beam” Support bar

• 2 x Beam connectors

• 4 x Knobs for beam connectors

• 2 x 5’ Truss I-Beam Sections

• 2 x 9’ Tri-pod stands

American DJ

User Instructions

Instructions for assembling your LTS-50T

1. After removing the contents from the box, locate the I-beam connectors and the end of one of

one of the 5’ I-beams with the perpendicular, or vertical support rod. Slide the I-beam connector

into the I-beam tube. Slide the other connector into the other tube. (See Fig. 1)

2. Insert the connector knob through the I-beam and the connector and fasten with wing nut. Do

the same for other connector knob. (See Fig. 2)

3. Now take two of the slide mount T-collar and attach to either end of the center support bar.

(See Fig. 3)

4. Slide the center support bar assembly onto the I-beam with attached connectors. (See Fig. 4)

5. Take the other 5’ I-beam (the side with the vertical support rod) and slide it over the beam con-

nector inside the center support bar assembly’s T-collars. (See Fig. 5)

6. With the both I-beams in place, insert the remaining two knobs into the other 5’ I-beam and

fasten with wing nut. (See Fig. 6)

7. On the T-collars above and below the center support bar, tighten the small knobs so the full

truss is secure. (See Fig. 7)

8. Set up the two Tri-pod stands. Adjust the telescopic adjustment assemblies by loosening the

knobs to preferred height. Slide two T-collars each onto the Tri-pod center posts. Move the truss

assembly into the T-collars. Then place another T-collar on the very top of each Tri-pod’s center

post. (See Fig.8)

9. Tighten the small knobs on the T-collars on the Tri-pod center posts at each end of the truss.

Slide a T-bar into each of the top T-collars on the Tri-pod posts. (See Fig. 9)

10. Fasten bolts and wing nuts into T-bar. Finish by tightening the small knobs on the T-collar.

(See Fig. 10)

11. Reposition if needed, recheck all connectors, and tighten all fastners before mounting any

fixtures to your completed LTS-50T trussing system.

Specifications: Model LTS-50T

Weight: 42 lbs.

System Capacity: 200 lbs.

Affordable Quality Lighting Products from

American DJ® Los Angeles, CA 90058

Portable Trussing System

LTS-50T Parts List:

Z-LTS/SB

fig. 3

Z-LTS-T

Z-LTS-I/KNOB

fig. 2

Z-LTS-I/C5 FT. I-BEAM

Z-LTS-I/C

*PERPENDICULAR

SUPPORT ROD

fig. 1

fig. 4

fig. 7

fig. 6

fig. 5

Z-LTS2/SK

Z-LTS-I/KNOB

5 FT. I-BEAM

Z-LTS-T

Z-LTS/LL-ADAPTOR

5 FT. I-BEAMZ-LTS-T

Z-LTS-T

Z-LTS2/TEL-ADJ

TRI-POD STAND

TRI-POD CENTER POST

fig. 8

Z-LTS2/LK

Z-LTS2/TEL-ADJ

Z-1.0/M6B

Z-1.0/M6

Z-1.0/M6B

Z-1.0/M6

Z-LTS2/SK

Z-LTS50/TB

fig. 9

Z-LTS2/SK

Z-UBNA Z-UBNA

fig. 10

American DJ LTS-50T User manual

American DJ LTS-50T User manual

American DJ LTS-50T User manual

Related papers

Other documents