American DJ LTS-50T User Instructions

Brand: American DJ

Model: LTS-50T

Type: User Instructions

LTS-50T

• 2 x T-bars

• 6 x Slide mount T-collars

• 1 x Center “I-Beam” Support bar

• 2 x Beam connectors

• 4 x Knobs for beam connectors

• 2 x 5’ Truss I-Beam Sections

• 2 x 9’ Tri-pod stands

American DJ

User Instructions

Instructions for assembling your LTS-50T

1. After removing the contents from the box, locate the I-beam connectors and the end of one of

one of the 5’ I-beams with the perpendicular, or vertical support rod. Slide the I-beam connector

into the I-beam tube. Slide the other connector into the other tube. (See Fig. 1)

2. Insert the connector knob through the I-beam and the connector and fasten with wing nut. Do

the same for other connector knob. (See Fig. 2)

3. Now take two of the slide mount T-collar and attach to either end of the center support bar.

(See Fig. 3)

4. Slide the center support bar assembly onto the I-beam with attached connectors. (See Fig. 4)

5. Take the other 5’ I-beam (the side with the vertical support rod) and slide it over the beam con-

nector inside the center support bar assembly’s T-collars. (See Fig. 5)

6. With the both I-beams in place, insert the remaining two knobs into the other 5’ I-beam and

fasten with wing nut. (See Fig. 6)

7. On the T-collars above and below the center support bar, tighten the small knobs so the full

truss is secure. (See Fig. 7)

8. Set up the two Tri-pod stands. Adjust the telescopic adjustment assemblies by loosening the

knobs to preferred height. Slide two T-collars each onto the Tri-pod center posts. Move the truss

assembly into the T-collars. Then place another T-collar on the very top of each Tri-pod’s center

post. (See Fig.8)

9. Tighten the small knobs on the T-collars on the Tri-pod center posts at each end of the truss.

Slide a T-bar into each of the top T-collars on the Tri-pod posts. (See Fig. 9)

10. Fasten bolts and wing nuts into T-bar. Finish by tightening the small knobs on the T-collar.

(See Fig. 10)

11. Reposition if needed, recheck all connectors, and tighten all fastners before mounting any

fixtures to your completed LTS-50T trussing system.

Specifications: Model LTS-50T

Weight: 42 lbs.

System Capacity: 200 lbs.

Affordable Quality Lighting Products from

American DJ® Los Angeles, CA 90058

Portable Trussing System

LTS-50T Parts List:

All manuals and user guides at all-guides.com

all-guides.com

Z-LTS/SB

fig. 3

Z-LTS-T

Z-LTS-I/KNOB

fig. 2

Z-LTS-I/C5 FT. I-BEAM

Z-LTS-I/C

*PERPENDICULAR

SUPPORT ROD

fig. 1

fig. 4

All manuals and user guides at all-guides.com

fig. 7

fig. 6

fig. 5

Z-LTS2/SK

Z-LTS-I/KNOB

5 FT. I-BEAM

All manuals and user guides at all-guides.com

Z-LTS-T

Z-LTS/LL-ADAPTOR

5 FT. I-BEAMZ-LTS-T

Z-LTS-T

Z-LTS2/TEL-ADJ

TRI-POD STAND

TRI-POD CENTER POST

fig. 8

Z-LTS2/LK

Z-LTS2/TEL-ADJ

Z-1.0/M6B

Z-1.0/M6

Z-1.0/M6B

Z-1.0/M6

Z-LTS2/SK

All manuals and user guides at all-guides.com

Z-LTS2/SK

Z-LTS50/TB

fig. 9

All manuals and user guides at all-guides.com

Z-LTS2/SK

Z-UBNA Z-UBNA

fig. 10

All manuals and user guides at all-guides.com

all-guides.com

American DJ LTS-50T User Instructions

American DJ LTS-50T User Instructions

American DJ LTS-50T User Instructions

Related papers

Other documents