Wentronic 30618 User manual

Category
Power supply
Type
User manual

This manual is also suitable for

Pillmannstraße 12 | 38112 Braunschweig | Germany
Read the instructions carefully and completely. It is part of the product and contains important notes for use. Keep this document!
Safety Instructions
Risk of life by electric shock Avoid contacting mains voltages!
Risk of self-intervention and misuse Do not modify or alter either the product or the accessories!
Do not open the housing.
Instructions for mains separation Attend to the delivered VDE Notes!
Install the product at an easily accessible place.
Risk of injury by tripping and falling Place, transport and install product, parts and acceories in a safe way.
Risk of injury by inappropriate ambient
conditions
Not suitable for children and people with physically and / or mentally
limited capabilities.
Only use in dry ambiance.
Risk of material damage by improper
product combination
The specications of all used products must match or be within the
specied range.
Material damage by improper
methods
Use product, product parts and accessories only in perfect condition.
Description and Function
Your product is a voltage converter, converting mains voltage to low voltage and eg. can be used in furnitures. The SET 24-XX LED slim transfor-
mer serie is characterized by constant output voltage, what your LED lighting protects and prolongs their lifespan. The compact design ts almost
anywhere.
Transformer housing
Terminals
Mounting slot
Seconrady side with cap
(Connecting of LED lighting)
Primary side with cap
(mains connection)
Intended Use
Constant-voltage transformers of the SET LED series are primarily made for parallel circuits. With varying the number of LEDs, the secondary current
varies, too. Only use the product like described in chapter Description and Function. Use it only in dry ambience. Other use is not permitted. Misuse
will void the warranty and liability.
Connecting and Operating
1. Compare all products to be compatible to each other.
2. Attend to the Safety Instructions and the VDE notes.
3. Turn off the mains fuse and check with a voltage tester to be sure, all lines are really stress-free. If in doubt, a electrician must do the
installation work.
4. Leave 50 mm space around all dimensions of the transformer when installing.
5. First, connect the secondary circuit (SEC) by removing the cap with a suitable Phillips head screwdriver.
6. Now you can see 2 free terminals at the secondary side.
7. Connect your LED lights in correct polarity to the terminals of the secondary circuit (SEC).
Alternatively connect lamps with DC plug to the DC jack, if existing.
For calculating the total power (P in Watt) of your LED lighting combination, multiply the current of your LED lighting (I in Ampere) with its voltage
(U in Volt). Therefor this applies: P=U*I.
>> In Parallel circuits, the voltage (U) stays constant.
>> In Serie circuits, the current (I) stays constant.
8. If all LEDs are connected to the secondary side right way, connect the primary circuit (PRI / 200-240 V AC) with its 2 terminals N and
L on to the electricity grid.
9. Reattach the cover caps and tighten them.
10. Fix the product by the 2 mounting holes on a rm, safe surface, if needed.
11. Turn the mains fuse on.
User‘s Manual for
LED transformers
3/8
Pillmannstraße 12 | 38112 Braunschweig | Germany
User‘s Manual for
LED transformers
The voltage transformer works when a voltage is applied on the primary side. It does not have its own switch and is maintenance-free.
Warranty and Responsibility
The producer grants a 2 years warranty.
As the manufacturer has no inuence on installation, warranty only applies to the product itself.
The manufacturer is not liable for damages to persons or property caused by improper installation, operation or maintenance.
Do not alter or modify the product or its accessories.
Any use other than described in this user`s manual is not permitted and causes loss of warranty, loss of guarantee, and non-liability.
We reserve our right for misprints and changes of the device, packing, or user`s manual.
Disposal Instructions
According to the European WEEE directive, electrical and electronic equipment must not be disposed with consumers waste. Its components must be
recycled or disposed apart from each other. Otherwise contaminative and hazardous substances can pollute our environment.
As a consumer, you are committed by law to dispose electrical and electronic devices to the producer, the dealer, or public collecting points at the end
of the devices lifetime for free. Particulars are regulated in national right. The symbol on the product, in the user`s manual, or at the packaging alludes
to these terms. With this kind of waste separation, application, and waste disposal of used devices you achieve an important share to environmental
protection.
WEEE Directive: 2012/19/EU
WEEE N
o
: 82898622
EC Declaration
With the CE sign Goobay
®
, a registered trademark of Wentronic GmbH ensures, that the product is conformed to the basic standards and directives.
Specications
Physical Size
Model 30530 30632 30612 30606 30618 30633
Input voltage (PRI) 200-240V~ AC, 50Hz
Output voltage (SEC) constant DC 24V
Output current max. 0.25A max. 0.50A max. 0.84A max. 1.25A max. 2.08A max. 0.625A
tc / ta 80/45°C
Protection class II
Temperature fuse 110°C
Ambient temperature -20 ~ +45°C
Power (W) 0-6 0-12 0-20 0.5-30 0-50 0.5-15
Standby power (W) 0.5
Protection level IP20
Primary and Secondary cable H03VVH2-F 2x0.75mm²
Dimensions (mm)
98x 45.5
x10.6
127 x49
x10
154 x 50 x14 159 x59 x18 185 x64 x22 123 x45 x19
Weight 0.042 0.059 0.097 0.157 0.248 0.068
Document
Revision date: 2014-01-28
Version 1
4/8
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8

Wentronic 30618 User manual

Category
Power supply
Type
User manual
This manual is also suitable for

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI