Festool CTL MINI I Operating instructions

Page is loading ...

6

HF-CT MINI/MIDI-2/CT15

204 200

NF-CT MINI/MIDI-2/CT15

204 202

7-1

7

Absaugmobil

Mobile dust

extractors

Aspirateurs

Seriennummer *

Serial number *

N° de série *

(T-Nr.)

CTL Mini 203448

CTL Midi 203449

CTL Mini I 201918, 201919, 201917, 201931

CTL Midi I 201926, 204379, 201922,

201925,201924

CTM Midi I 201934, 201933, 10019662,

201935

CT 15 E 201941, 201944, 201943

de

EG-Konformitätserklärung. Wir erklären

in alleiniger Verantwortung, dass dieses Produkt

allen einschlägigen Bestimmungen der folgenden

Richtlinien einschließlich ihrer Änderungen ent-

spricht und mit den folgenden Normen überein-

stimmt:

en

EC-Declaration of Conformity. We declare

under our sole responsibility that this product is in

conformity with all relevant provisions of the fol-

lowing directives including their amendments and

complies with the following standards:

fr

CE-Déclaration de conformité communau-

taire. Nous déclarons sous notre propre respons-

abilité que ce produit est conforme aux normes ou

documents de normalisation suivants:

es

CE-Declaración de conformidad. Declaramos

bajo nuestra exclusiva responsabilidad que este

producto corresponde a las siguientes normas o

documentos normalizados:

it

CE-Dichiarazione di conformità. Dichiariamo

sotto la nostra esclusiva responsabilità che il pre-

sente prodotto e conforme alle norme e ai docu-

menti normativi seguenti:

nl

EG-conformiteitsverklaring. Wij verklaren op

eigen verantwoordelijkheid dat dit produkt voldoet

aan de volgende normen of normatieve documen-

ten:

sv

EG-konformitetsförklaring. Vi förklarar i eget

ansvar, att denna produkt stämmer överens med

följande normer och normativa dokument:

ﬁ

EY-standardinmukaisuusvakuutus. Va-

kuutamme yksinvastuullisina, etta tuote on seu-

raavien standardien ja normatiivisten ohjeiden

mukainen:

da

EF-konformitetserklæring Vi erklærer at

have alene ansvaret for, at dette produkt er i over-

ensstemmelse med de følgende normer eller

normative dokumenter:

nb

CE-Konformitetserklæring Vi erklærer på

eget ansvar at dette produktet er i overensstem-

melse med følgende normer eller normative doku-

menter:

pt

CE-Declaração de conformidade: Declara-

mos, sob a nossa exclusiva responsabilidade, que

este produto corresponde às normas ou aos docu-

mentos normativos citados a seguir:

ru

Декларация соответствия ЕС: Мы заявляем

с исключительной ответственностью, что данный

продукт соответствует следующим нормам или

нормативным документам:

cs

ES prohlašeni o shodě: Prohlašujeme s vešk-

erou odpovědnosti, že tento vyrobek je ve shodě s

nasledujicimi normami nebo normativnimi doku-

menty:

pl

Deklaracja o zgodności z normami UE: Ninie-

jszym oświadczamy na własną odpowiedzialność,

że produkt ten spełnia następujące normy lub

dokumenty normatywne:

________________________________________

2006/42/EG, 2014/30/EU

2)

, 2014/53/EU

3)

, 2011/65/EU

EN 60335-1:2012, EN 60335-2-69:2012, EN

55014-1:2017

2)

, EN 55014-2: 2015

2)

, EN 61000-

3-2: 2015

2) 3)

, EN 61000-3-3: 2014

2) 3)

, EN 300

328:2016 V2.1.1

3)

, EN 301 489-1:2017 V.2.1.1

3)

, EN

301 489-17:2017 V3.1.1

3)

, EN 50581: 2012

________________________________________

Festool GmbH

Wertstr. 20, D-73240 Wendlingen

GERMANY

Wendlingen, 2019-08-07

Markus Stark

Head of Product Development

Ralf Brandt

Head of Standardization & Approbation

1)

im deﬁnierten Seriennummer-Bereich (S-Nr.) von/in the speciﬁed serial number

range (S-Nr.) from/dans la plage de numéro de série (S-Nr.) de 40000000 - 49999999

2)

gilt in Kombination mit Akku/valid in combination with battery pack/valable en

combinaison avec batterie BP 18 Li 5,2 AS, BP 18 Li 6,2 AS, BP 18 Li 3,1 C

3)

gilt in Kombination mit Bluetooth

®

Akku/valid in combination with Bluetooth

®

battery pack/valable en combinaison avec Bluetooth

®

batterie BP 18 Li 5,2 ASI, BP

18 Li 6,2 ASI, BP 18 Li 3,1 CI

Die Wortmarke Bluetooth® und die Logos sind eingetragene Marken von Bluetooth

SIG, Inc. und werden von der TTS Tooltechnic Systems AG & Co. KG und somit von

Festool unter Lizenz verwendet./ The Bluetooth® word mark and the logos are

registered trademarks of Bluetooth SIG, Inc.; they are used by TTS Tooltechnic

Systems AG &Co. KG, and therefore by Festool, under licence./ La marque verbale

Bluetooth® et les logos sont des marques déposées de Bluetooth SIG, Inc. et sont

utilisés sous licence par TTS Tooltechnic SystemsAG &Co.KG et donc par Festool

GmbH.

720425_C

Page is loading ...

Contents

1 Safety warnings.........................................12

2 Symbols.....................................................12

3 Parts of the machine.................................13

4 Technical data........................................... 13

5 Intended use..............................................13

6 Commissioning..........................................13

7 Settings......................................................14

8 Working..................................................... 14

9 Service and maintenance..........................15

10 Environment..............................................15

1 Safety warnings

Warning! Read and observe all instruc

tions and safety warnings. Failure to observe

the instructions and safety warnings may lead

to electric shocks, fires and/or serious injuries.

Keep all safety warnings and instructions for

future reference.

– This appliance must not be used by persons

(including children) with reduced physical,

sensory or mental capabilities, or lack of

experience and knowledge.

Children need

to be supervised to ensure they do not play

with the device.

– If this device's mains power cable is dam

aged, it must be replaced by an authorised

service workshop to prevent it posing a

risk.

– Always operate with the filter system in

stalled.

– Warning Operators must be appropriately

instructed in the use of this machine.

– The mains plug must always be disconnec

ted from the socket before performing

cleaning or maintenance tasks, when re

placing consumables or when converting

the machine.

– Warning Only use the electrical outlet

module on the machine for the purposes

specified in the instructions.

– Warning If foam or fluid starts to escape,

switch off the machine immediately.

– Caution Regularly clean the water level

limiting device and inspect it for signs of

damage.

– Not suitable for extracting fluids that foam

excessively.

– Sound pressure level as per EN

60335-2-69/uncertainty K

70 dB(A)/3 dB

– Hand-arm vibration value as per EN

60335-6-69/uncertainty K

< 2.5 m/s² / 1.5 m/s²

– Not suitable for extracting hazardous dust.

– Risk of explosion and fire: Do not extract:

– Sparks or hot dust;

– combustible or explosive materials (e.g.

magnesium, aluminium, petrol, diluting

agents);

– aggressive materials (e.g. acid, alkaline

solutions, solvents);

– chemically reactive materials, which lead

to the generation of heat, acids/bases,

gases, etc. (e.g. reactive two-component

materials, aluminium and water).

– Observe all national safety regulations as

well as the material manufacturer's speci

fications!

– Always use suitable protective equipment!

– If intact following a visual inspection, work

in a dry environment according to instruc

tions!

– Check the plug, the electrical outlet mod

ule, the cable and the filter regularly in or

der to prevent a hazard. Damaged electri

cal components must be replaced by an au

thorised service workshop only.

– Do not lift or transport the device using a

crane hook or lifting gear.

– The mobile dust extractor must not be car

ried by the suction hose mount

[1-3].

– CAUTION! Electric shock due to static dis

charge. The tool is equipped with a "non-

antistatic (AS) suction hose" in the scope of

delivery. Use the optional AS suction hose

to use the antistatic function provided on

the tool.

– Only place the tool on level ground and se

cure it against rolling away.

2 Symbols

Warning of general danger

Warning of electric shock

Read the operating instructions and

safety instructions.

Do not dispose of it with domestic

waste.

Pull out the mains plug

English

12

Wear a dust mask.

Do not climb on the unit

3 Parts of the machine

[1-1]

Electrical outlet module

[1-2]

Cable and accessory holder

[1-3]

Suction hose mount

[1-4]

Handle

[1-5]

Lock

[1-6]

Filter drawer

[1-7]

Locking clip

[1-8]

Exhaust opening

[1-9]

Dirt trap

[1-10]

On/off switch

[1-11]

MAN button

[1-12]

Suction power adjustment

The specified illustrations appear at the begin

ning of the Operating Instructions.

4 Technical data

Mobile dust extractors

Power consumption 350–1200 W

Max. electrical outlet module connected load EU

CH, DK

GB

2200 W

1150 W

1610 W

Max. suction capacity (air), extractor/turbine 130 m³/h / 222 m³/h

Max. vacuum, turbine 24,000 Pa

Filter surface area 3508 cm²

Suction hose D 27/32 mm x 3.5 m

Mains power cable length 5.5 m

Sound pressure level as per EN 60335-2-69/uncertainty K 70 dB(A)

Hand-arm vibration value as per EN 60335-2-69/uncertainty K < 2.5 m/s² / 1.5 m/s²

Type of protection IP X4

Container capacity 15 l

Dimensions L x W x H 470 x 320 x 435 mm

Weight 11.2 kg

5 Intended use

Mobile dust extractor suitable for

– Extracting non-hazardous dust, dirt, sand

and chips,

– Extracting water,

– Increased loads during commercial use,

according to IEC/EN 60335-2-69.

The mobile dust extractor is only suitable for

indoor use.

The user is liable for improper or non-in

tended use.

6 Commissioning

WARNING

Unauthorised voltage or frequency!

Risk of accidents

► Observe the specifications on the ma

chine's name plate.

► Observe country-specific regulations.

6.1 Initial commissioning

► Insert the filter bag [2].

► Connect the suction hose[3].

English

13

6.2 Connecting the mobile dust extractor

WARNING

Risk of injury from uncontrolled tool start-

up

► Before switching on ensure that the con

nected tool is switched off.

WARNING

Risk of injury from electric current

► Insert the mains plug into an earthed sock

et.

► Do not reach into the electrical outlet mod

ule on the mobile dust extractor.

While the mobile dust extractor is connec

ted to the mains socket, an electric cur

rent is running through electrical outlet

module on the mobile dust extractor at all

times.

Connecting the mobile dust extractor to a

mains socket

The mobile dust extractor is switched off.

► Connect the power cable to a mains socket.

The electrical outlet module [1-1] is live.

Switching the mobile dust extractor to standby

mode

► Press the on/off switch[1-10].

The electrical outlet module [1-1] is live.

The green LED [1-12] indicates standby

mode.

Starting the mobile dust extractor automati

cally

The mobile dust extractor is in standby mode.

► To start the mobile dust extractor automati

cally: Switch on the connected tool.

Starting the mobile dust extractor manually

The mobile dust extractor is in standby mode.

► Press the MAN button [1-11].

Pull the mains plug from the socket when

you are not using the mobile dust extrac

tor and before performing any cleaning and

maintenance work.

6.3 Connecting power tools

WARNING

Risk of injury

► Observe the maximum electrical outlet

module connected load (see section "Tech

nical data").

► Switch off the power tool.

Connecting a mains-powered power tool to the

mobile dust extractor

► Connect the power tool to the electrical out

let module [1-1].

The power tool is connected to the mobile dust

extractor via the power cable.

7 Settings

7.1 Adjusting the suction power

► Press the plus or minus button [1-12] while

extracting.

7.2 Temperature cut-out

A temperature cut-out switches the mobile dust

extractor off when it reaches a critical tempera

ture to prevent overheating. The bottom

LED

[1-12] indicates a fault.

LED lights up red Excessive temperature

► Switch off the mobile dust extractor, let it

cool down.

► Switch on the mobile dust extractor again

after approx. five minutes.

8 Working

8.1 Dust extraction

Extracting dry materials

Always use a filter bag.

8.2 Extracting wet materials/liquids

Remove the filter bag!

Use a special wet filter.

The dust extractor stops automatically when

the maximum fill level is reached.

The bottom LED [1-12] lights up red.

► Switch off the mobile dust extractor [1-10].

► Open the locking clips [1-7] and remove the

top section of the machine.

► Empty the dirt trap [1-9].

After wet extraction, allow the main filter to dry!

Dry the mobile dust extractor before extracting

dry dust.

English

14

CAUTION

Hazardous dust

Damage to the respiratory passage

► After extracting wet materials, remove the

wet filter and replace it with the main filter

for dry materials.

CAUTION

Escaping foam and fluids

► Switch off and empty the machine immedi

ately.

8.3 Blow-out function

► Open the grille in front of the exhaust open

ing

[1-8].

► Insert the suction hose in the exhaust open

ing [1-8].

► In standby mode, press the MAN but

ton [1-11].

8.4 Changing the filter bag with minimal

dust

► Open the locking clips and remove the top

section of the machine [2].

► Pull the tab on the filter bag until the filter

bag opening is fully closed.

The filter bag is now securely closed and can be

removed.

► Fit the top section of the machine and close

the locking clips.

8.5 Changing the filter element [6]

► Pull out the used filter drawer [1-6].

► Dispose of the used filter drawer in accord

ance with statutory regulations.

► Insert the new filter drawer [1-6].

Order numbers for accessories, filters and

consumables in the Festool catalogue or

online at "www.festool.com".

– Only use original Festool accessories and

consumables. Only accessories tested and

approved by Festool are safe and perfectly

adapted to the machine and application.

NOTICE

Damage to the motor

► Never extract material without a main filter

or with a damaged main filter, as this can

damage the motor.

8.6 After finishing work

► Switch off the mobile dust extractor and

pull out the mains plug.

► Vacuum and wipe the inside and outside of

the mobile dust extractor to clean it.

► Empty the dirt trap.

► Wind up the mains power cable.

► Place the mains power cable [4-1] in the

sealable depot. To do so, lay the power ca

ble through the recess

[4-2].

► Disconnect the suction hose [5-1] and fix it

to the mobile dust extractor using the suc

tion hose attachment [1-3].

► Regularly clean the fill level sensors [7-1]

and check for damage.

► Place the mobile dust extractor in a dry

room inaccessible to unauthorised users.

The lid of the depot also serves as a stor

age area for tools.

9 Service and maintenance

WARNING

Risk of injury, electric shock

► Always pull the mains plug from the socket

before performing any servicing and main

tenance work.

► All maintenance and repair work which re

quires the motor housing to be opened

should always be carried out by an author

ised service workshop.

WARNING

Incorrect testing may damage the machine

and injure users

► Special information is required for testing

the electrical safety. This is available from

your country's Festool service workshop.

Customer service and repairs must

only be carried out by the manufac

turer or service workshops. Find the

nearest address at:

www.festool.co.uk/service

Always use original Festool spare

parts. Order no. at:

www.festool.co.uk/service

EKAT

1

2

3

5

4

10 Environment

Do not dispose of the device in the

household waste! Recycle devices, ac

cessories and packaging. Observe appli

cable national regulations.

English

15

EU only: In accordance with the European Di

rective on waste electrical and electronic

equipment and implementation in national law,

used power tools must be collected separately

and handed in for environmentally friendly re

cycling.

Information on REACH: www.festool.com/reach

English

16

Page is loading ...

indsamles separat og afleveres til miljøvenlig

genvinding.

Informationer om REACh: www.festool.com/

reach

Dansk

49

Page is loading ...

Festool CTL MINI I Operating instructions

Festool CTL MINI I Operating instructions

in other languages

Related papers

Other documents