Bunn Single® SH Soft Heat® DBC® Stainless 120/240V User manual

Brand: Bunn

Model: Single® SH Soft Heat® DBC® Stainless 120/240V

Category: Coffee making accessories

Type: User manual

This manual is also suitable for

USE & CARE INSTRUCTIONS for BrewWISE

System

(Includes G92T DBC Grinder and DUAL SH DBC Brewer with Smart Funnel™)

STEP 1

STEP 2 STEP 3 STEP 4

34481 011403

Select the desired batch

size and coffee ﬂavor on

the grinder. It is not nec-

essary to select a size on

the brewer.

Discard the grounds and

filter when brewing is

completed.

Momentarily press and

release the BREW button.

Place an empty server

under the funnel.

Slide funnel into the fun-

nel rails. The brewer reads

the batch size and ﬂavor

ground through a chip in

the funnel handle and will

automatically select the

correct settings to brew.

Grind the proper amount of

fresh coffee into the Smart

Funnel™ using the G92-

HD with Smart Funnel™

operation.

Insert a BUNN

ﬁlter into

the funnel.

A batch size must be cho-

sen at the brewer when

grounds are not obtained

from a Smart Funnel™

compatible grinder.

STEP 5

STEP 6 STEP 7

STEP 8

STEP 9 STEP 10

Level grounds by gently

shaking.

Press the ON/OFF button

to ON.

STEP 2

STEP 4

Clean mineral deposits

and rinse. Using a paper

clip, make sure all holes

are open.

STEP 1

Remove the sprayhead.

STEP 5

Use a clean damp cloth

rinsed in nonabrasive,

mild detergent to clean all

surfaces.

Remove the lid of the

server.

STEP 3

Reinstall the sprayhead.

CLEANING

COFFEE BREWING

34481 031617

STEP 6

STEP 8STEP 7 STEP 9 STEP 10

STEP 12 STEP 14STEP 11 STEP 15

Unscrew the inlet cap.

Pull out lid assembly.

Clean inlet tube with the

medium sized brush

(BOM #00675.0000) and

cleaning product solution.

Rinse well. Reassemble

the lid making sure to

replace the retainer cap.

Clean the sight gauge with

the small brush (BOM

#00674.0000) and reas-

semble.

Remove the glass tube.

Make sure reservoir is

empty and unscrew the

sight gauge cap.

Use a clean damp cloth

rinsed in nonabrasive,

mild detergent to clean all

surfaces.

Thoroughly rinse entire

inside of the server. DO

NOT immerse server in

water.

STEP 13

Reinstall glass tube and

the sight gauge cap.

Use a small brush (BOM

#00674.0000) to thor-

oughly scrub the faucet

shank.

Allow the parts to soak in

a sanitizer solution for a

minimum of ten minutes.

Remove the faucet parts

from the sanitizer solution.

Allow parts to air-dry

overnight.

Transfer these parts to a

three compartment sink

for cleaning. Fill the ﬁrst

sink with a soap solution

using a mild detergent,

the second sink is used for

clean rinse and the third

sink is used for a sanitizer

solution (75°F warm

non-chlorine sanitizing

solution).

STEP 16

STEP 17 STEP 18 STEP 19 STEP 20

Turn the faucet wing nut in

a clockwise direction and

remove the faucet from

the dispenser. Unscrew

the faucet cap from the

faucet body and disas-

semble all faucet parts.

Use a small brush (BOM

#00674.0000) to thor-

oughly scrub the faucet

body.

CLEANING (Continued)

USE & CARE INSTRUCTIONS for BrewWISE

System

(Includes G92T DBC Grinder and DUAL SH DBC Brewer with Smart Funnel™)

Bunn Single® SH Soft Heat® DBC® Stainless 120/240V User manual

Brand: Bunn

Model: Single® SH Soft Heat® DBC® Stainless 120/240V

Category: Coffee making accessories

Type: User manual

This manual is also suitable for

Download PDF

report

in other languages

italiano: Bunn Single® SH Soft Heat® DBC® Stainless 120/240V Manuale utente

Bunn Single® SH Soft Heat® DBC® Stainless 120/240V User manual

This manual is also suitable for

Bunn Single® SH Soft Heat® DBC® Stainless 120/240V User manual

in other languages

Related papers

Other documents