ZyXEL DMA2501 Quick start guide

www.zyxel.com

Full HD Digital Media Streamer

Firmware v1.00

Edition 1, 5/2010

DMA2501

CONTENTS

ENGLISH 5

DEUTSCH 21

ESPAÑOL 39

FRANÇAIS 57

ITALIANO 75

NEDERLANDS 95

SVENSKA 113

ZyXEL Communications Corporation

4

Device Panels

POWER

LED

REMOTE CONTROL

ACTIVITY LED

IR

RECEIVER

USB

PORT

ETHERNET

PORT

HDMI PORT

POWER

AV PORT

OPTICAL

PORT

ENGLISH

5

Connect Your DMA2501

This is a hardware connection overview. Take the following steps to set

up your DMA2501’s hardware connections. Use either the cables that

came with your DMA2501, or those that came with your TV or Internet

access device.

Turn off your TV before you connect the DMA2501.

or

1

2

3

4

5

ENGLISH

6

1. If your TV has an HDMI connector, use an HDMI cable to connect the

DMA2501’s HDMI connector to the TV. Then go to step 3.

If your TV does not have an HDMI connector:

Use a composite AV to 3 RCA cable to connect the DMA2501’s AV

jack to the TV.

2. If your stereo has an optical jack, use a digital audio cable to connect

it to the DMA2501’s OPTICAL jack.

3. Skip to step 4 if you will only play files from a USB device. To play

media files located on computers or devices on your network or the

Internet, connect the DMA2501’s Ethernet port.

• Use the straight-through Ethernet cable to connect to an Ethernet

switch, router, or hub.

• Or use a cross-over Ethernet cable (not included) to connect

directly to your computer.

ENGLISH

7

4. To play files from a USB device, connect it to the DMA2501’s USB

port. Make sure the USB device also uses its external power supply if

it has one.

5. Connect the POWER socket to a power source using only the

included power adaptor.

6. If you want to stand the DMA2501 up vertically, attach the included

stand as shown next.

Configure the DMA2501

1. Turn on the TV and set its video source to the DMA2501’s

connection: HDMI or composite (AV).

2. Install the remote control’s batteries.

8

Point the remote at the black dot on the front of the DMA2501. The

DMA2501 remote is sensitive to input from the remote. Holding a button

on the remote down may register as multiple pushes.

3. Turn on the DMA2501. The POWER light turns green.

 Check your power connection if the power light does not

come on.

4. If the DMA2501’s picture displays on the TV properly, continue to the

next step. Otherwise, use the remote’s OUTPUT button to change the

video mode. Wait a few seconds during each mode. When you get to

the correct mode, use the arrow and OK buttons to select OK.

5. Press the remote’s SETUP button. Use the arrow and OK buttons to

select System Setup.

6. Press OK to select Language.

ENGLISH

9

7. Press OK to display a language list. Use the up and/or down arrow

and OK buttons to select your language.

Wireless Setup

Connect a ZyXEL NWD-211AN or NWD-270N wireless USB adapter to

the USB port and use this section to set up a wireless network

connection. For wireless connections the DMA2501 only supports

getting an IP address automatically so your network must have a DHCP

server to assign the DMA2501 an IP address.

1. Press the remote’s SETUP button and use the arrow and OK buttons

to select Network Setup and then the Network Wizard.

10

2. Select Wireless.

3. The DMA2501 scans and lists the wireless networks in the area.

Select the wireless network to which you want to connect and press

OK.

• Red: this first dot (on the left) indicates a weak signal.

• Yellow: (the second dot) indicates a fair signal.

• Green: (the third dot) indicates a strong signal.

ENGLISH

11

4. The DMA2501 lists the selected wireless network’s key settings. If the

wireless network uses security, select Key Value and use the remote

control’s arrow and OK buttons to input the password. Then select

Next.

5. The DMA2501 applies your settings and your DMA2501’s network

setup is complete. Select Done to return to the Network Setup

menu.

6. Select IP Setup.

12

7. Your wireless setup is complete if the DMA2501 has been assigned

an IP address. Otherwise use the wireless wizard again and make

sure you use the correct settings.

If you change the wireless AP’s settings, disconnect and reconnect the

DMA2501’s power and configure the wireless wizard again.

Media Server Software

Install the included media server software to let the DMA2501 play files

stored on your computer.

To just use a USB device, skip to page 17. You can only install the media

server software on a Windows computer. See page 18 for more details.

Install the Media Server Software

1. Put the CD into your CD-ROM. Click Setup in

the following screen.

 If this screen does not display, locate and

double-click setup.exe.

ENGLISH

13

2. Select your language and click OK.

3. The installation wizard appears. Follow the directions to install the

software.

4. In the final wizard screen, select Launch ZyXEL Media Server and

click Finish.

14

Configure the Media Server

1. This icon displays in the system tray (usually in the bottom right

corner) after the installation is done. Double-click the icon to open the

server configuration screens.

2. Use the Options tab to select the language and set the media server

to automatically start when the computer turns on.

3. Use the Media List tab to select folders of files for your computer to

share with the DMA2501 and then turn on the media sharing service

by clicking the Start Service icon.

ENGLISH

15

• Click the Add a Folder icon and browse to select a folder that you

want to share.

• To remove a folder from the list, select it and click the Remove a

Folder icon.

• Stop the service to be able to edit the shared media list.

You can use the DMA2501 to display photos and play videos and music.

This is an example to play video files.

1. Use the remote’s VIDEO, arrow and OK buttons to select Media

Server.

2. Use the remote’s arrow and OK buttons to select your media server’s

name.

16

3. Select Video and then All Videos.

4. Select a video file and use the remote’s OK button to play.

Set Up Your Computer’s IP Address

If you connected the DMA2501’s Ethernet port directly to your computer,

set both of the DMA2501 and your computer to use a static IP address in

the 192.168.1.3 - 192.168.1.254 range with a subnet mask of

255.255.255.0. This lets the computer and DMA2501 communicate.

Note down your computer’s current IP settings before you change them.

See your User’s Guide for information on setting up your computer’s IP

address. Use the remote’s Setup, arrow, OK and number 0~9 buttons to

set up the DMA2501’s IP address.

ENGLISH

17

Play Files

Here is how to play a video file from a connected USB device. Playing

other files works in a similar way.

1. Press the remote’s VIDEO and then OK button.

2. Use the remote’s arrow and OK buttons to select a USB device to

access.

3. Navigate to the file you want to play. You may need to go through

multiple layers of folders. Use the left or right arrow button to go to the

previous or next page of entries. This example uses a file in Video.

The total and

the available

storage size of

the selected

device or disk.

The number of

the item

currently

selected

followed by the

total number of

items in the

menu.

The file name and the type.

18

4. Use the remote’s OK button to play a video file.

 Files with unsupported formats or codecs may not display

properly.

The DMA2501 supports the following file formats. See the User’s Guide

for more details.

Requirements

 If you have trouble installing the media server software,

make sure your computer meets the following requirements.

Audio Audio Container: AAC, M4A, MPEG audio (MP1, MP2, MP3, MPA), WAV,

WMA, FLAC, OGG

Audio Decoders: Dolby Digital, DTS, WMA, WMA Pro, MPEG-1 Layer 1/2/3,

MPEG-4 AAC-LC, MPEG-4 HE-AAC, MPEG-4 BSAC, LPCM, FLAC, Vorbis

Video Video Containers: MPEG1/2/4, MPEG1/2 PS (M2P, MPG, DAT, VOB)

MPEG2 Transport Stream (TS, TP, TRP, M2T, M2TS, MTS), AVI, ASF, WMV

Matroska (MKV), MOV (H.264), MP4, RMP4

Video Decoders: H.264, WMV9, VC1, MPEG 1/2/4, Xvid, AVC

Photo TIF/TIFF, PNG, GIF, BMP, JPEG

Microsoft Windows XP or Windows Vista

CPU 1.8 GHz Pentium 4 or above

Memory 512 MB or above recommended

Peripherals CD-ROM drive

Hard Disk 20 MB or above.

ENGLISH

19

The Remote Control

MUTE turns off the sound.

REC, FUNC and COPY are

reserved for future use.

Power turns the DMA2501 on or

off.

Help displays help information for a

screen.

OUTPUT switches the video output

type.

SORT/EPG rearranges the order of

the files.

SUBTITLE changes the subtitles.

LANGUAGE changes the language.

Press MENU while playing a DVD

file to open the DVD menu.

STOP function during file playback.

ZOOM zooms in on a photo or

video.

A-B lets you select start and stop

times to repeat an interval for a

playing music or video.

Use 0~9 to input numbers. Use

GOTO to jump to a specific

percentage (%) or time slice

(hh:mm) of a playing music or

video file.

Previous, and next functions during

file playback.

BACK return to the previous menu.

INFO displays details about the

playing video or photo file.

VOL -/+ adjust the

volume.

HOME return to the main

menu.

SETUP opens the SETUP

menu for configuring

settings.

BGM select and play

background music.

REPEAT keeps playing

(loops) the file.

ROTATE turns a photo 90°

clockwise.

SLOW/SLIDE functions to

slow down a playing video

or display pictures

automatically.

Use the OK and arrow

buttons to go through the

menus and play your files.

IMEDIA opens a menu of

Internet media to play.

PICTURES opens a menu

of picture files to view.

VIDEO opens a menu of video files

to play.

MUSIC opens a menu of music files

to play.

Page is loading ...

54

El DMA2501 soporta los siguientes formatos de archivo. Consulte la

Guía del usuario para más detalles.

Requisitos

 Si tiene problemas para instalar el software del servidor

multimedia, compruebe si su ordenador cumple con los

requisitos siguientes.

Audio Audio Container: AAC, M4A, MPEG audio (MP1, MP2, MP3, MPA), WAV,

WMA, FLAC, OGG

Audio Decoders: Dolby Digital, DTS, WMA, WMA Pro, MPEG-1 Layer 1/2/3,

MPEG-4 AAC-LC, MPEG-4 HE-AAC, MPEG-4 BSAC, LPCM, FLAC, Vorbis

Video Video Containers: MPEG1/2/4, MPEG1/2 PS (M2P, MPG, DAT, VOB)

MPEG2 Transport Stream (TS, TP, TRP, M2T, M2TS, MTS), AVI, ASF, WMV

Matroska (MKV), MOV (H.264), MP4, RMP4

Video Decoders: H.264, WMV9, VC1, MPEG 1/2/4, Xvid, AVC

Photo TIF/TIFF, PNG, GIF, BMP, JPEG

Microsoft Windows Windows XP o Windows Vista

CPU Pentium 4 a 1.8 GHz o superior

Memoria 512 MB o más recomendado

Periféricos Unidad de CD-ROM

Disco duro 20 MB o más.

Page is loading ...

FRANÇAIS

71

3. Allez sur le fichier que vous voulez lire. Vous devrez peut-être

parcourir plusieurs niveaux de dossiers. Utilisez les boutons fléchés

pour aller à la page précédente ou suivante des entrées. Cet exemple

utilise un fichier dans Video (vidéo).

4. Utilisez le bouton fléché et le bouton OK de la télécommande pour

sélectionner et lire un fichier vidéo.

 Les fichiers ou codecs d'un format non pris en charge

risquent de ne pas s'afficher correctement.

Le DMA2501 prend en charge les formats de fichiers suivants. Voir le

guide de l'utilisateur pour plus de détails.

Audio Audio Container: AAC, M4A, MPEG audio (MP1, MP2, MP3, MPA), WAV,

WMA, FLAC, OGG

Audio Decoders: Dolby Digital, DTS, WMA, WMA Pro, MPEG-1 Layer 1/2/3,

MPEG-4 AAC-LC, MPEG-4 HE-AAC, MPEG-4 BSAC, LPCM, FLAC, Vorbis

Video Video Containers: MPEG1/2/4, MPEG1/2 PS (M2P, MPG, DAT, VOB)

MPEG2 Transport Stream (TS, TP, TRP, M2T, M2TS, MTS), AVI, ASF, WMV

Matroska (MKV), MOV (H.264), MP4, RMP4

Video Decoders: H.264, WMV9, VC1, MPEG 1/2/4, Xvid, AVC

Photo TIF/TIFF, PNG, GIF, BMP, JPEG

Le nom de fichier et le type.

Le nombre

d'éléments

actuellement

sélectionnés suivi du

nombre total

d'éléments dans le

menu.

Page is loading ...

90

3. Navigare fino al file da riprodurre. Può essere necessario passare più

livelli di cartelle. Utilizzare i tasti sinistra o destra per passare alla

pagina di voci precedente o successiva. In questo esempio viene

utilizzato un file in Video (video).

4. Utilizzare i pulsanti freccia e OK del telecomando per selezionare e

riprodurre un file video.

 I file con formati o codec non supportati possono non essere

visualizzati correttamente.

DMA2501 supporta i seguenti formati di file. Cedere la Guida dell'utente

per ulteriori informazioni.

Audio Audio Container: AAC, M4A, MPEG audio (MP1, MP2, MP3, MPA), WAV,

WMA, FLAC, OGG

Audio Decoders: Dolby Digital, DTS, WMA, WMA Pro, MPEG-1 Layer 1/2/3,

MPEG-4 AAC-LC, MPEG-4 HE-AAC, MPEG-4 BSAC, LPCM, FLAC, Vorbis

Video Video Containers: MPEG1/2/4, MPEG1/2 PS (M2P, MPG, DAT, VOB)

MPEG2 Transport Stream (TS, TP, TRP, M2T, M2TS, MTS), AVI, ASF, WMV

Matroska (MKV), MOV (H.264), MP4, RMP4

Video Decoders: H.264, WMV9, VC1, MPEG 1/2/4, Xvid, AVC

Foto TIF/TIFF, PNG, GIF, BMP, JPEG

Nome e tipo di file.

Il numero

dell'elemento

correntemente

selezionato seguito

dal numero totale di

elementi presenti nel

menu.

Page is loading ...

ZyXEL DMA2501 Quick start guide

Related papers

Other documents