Page is loading ...
www.infineon.com
Please note that Cypress is an Infineon Technologies Company.
The document following this cover page is marked as “Cypress” document as this is the
company that originally developed the product. Please note that Infineon will continue
to offer the product to new and existing customers as part of the Infineon product
The fact that Infineon offers the following product as part of the Infineon product
portfolio.
Continuity of document content
portfolio does not lead to any changes to this document. Future revisions will occur
when appropriate, and any changes will be set out on the document history page.
Continuity of ordering part numbers
Infineon continues to support existing part numbers. Please continue to use the
ordering part numbers listed in the datasheet for ordering.
HX3 USB 3.0 SHARED LINKTM HUB DEVELOPMENT KIT
CY4613 QUICK START GUIDE
Step 2: Powering the HX3 Board
• Plug the AC-DC adapter into an AC wall power
receptacle. Connect the power supply plug to the
board’s DC supply jack (J1)
• The Power LED (PWR) glows green to indicate that
the board is powered and the Suspend Status LED
(SUSP) glows amber to indicate that the hub is in
Suspend State
Step 1: Conguring the HX3 Board
• Unpack the kit contents which include the DVK board,
12-V/3-A AC-DC adapter with four types of plugs,
USB 3.0 ‘A to micro-B’ cable and jumpers
• Ensure that the Conguration Mode Select Jumpers
(J5 and J6) are set for default operation as shown
above. Ensure that pins 2 and 3 are shorted on all the
3-pin jumper blocks except J28 as shown in step 2
image. Ensure that pins 2 and 4 are shorted on both
the 4-pin jumper blocks (J7 and J10). Also short pins 1
and 2 on J28 and J20
21
J5
J6
Pin 3 Pin 2 Pin 1
Conguration
Mode Select Jumpers
(J5 and J6)
Pin 3
Pin 3
Pin 2
Pin 4
4 Pin Jumper Block
3 Pin Jumper Block
Pin 2
Pin 1
Pin 1
DC Supply
Jack (J1)
J28
Power
LED (PWR)
Suspend
Status
LED (SUSP)
J20
Step 4: Identifying Standard and Shared LinkTM ports
• Identify the three types of downstream ports on
the board:
1. Standard USB 3.0 downstream ports (DS3 and DS4)
2. Shared Link
TM
USB 2.0 downstream ports
(DS1 and DS2)
3. Shared Link SS (SuperSpeed) downstream ports
(DS1 and DS2)
Step 3: Connecting the HX3 Board to a USB 3.0
PC / Laptop
• Connect the micro-B end of the USB 3.0 cable to the
board’s upstream port; connect the other end to the
USB 3.0 receptacle on a PC / laptop. The Suspend
Status LED (SUSP) turns off (on a PC / laptop running
Windows 7)
Note: The behavior of the SUSP LED varies across
operating systems. For example, in Windows 8, the
SUSP LED turns off momentarily and turns on again
when there is no further USB activity on the board
43
Standard
USB 3.0
downstream
port (DS3 and DS4)
Shared Link USB 2.0
downstream ports
(DS1 and DS2)
Shared Link SS
downstream ports
(DS1 and DS2)
USB 3.0
port on the
PC/Laptop
USB cable
connected
to board’s
upstream port
Suspend
Status LED
J10J7
CY4613 QUICK START GUIDE
Step 5: Demonstrating USB 3.0 Data Transfer on a
Standard USB 3.0 port
• Get a USB 3.0- certied ash drive and store a 2 GB
le on it. Connect the ash drive to one of the
two Standard USB 3.0 downstream ports (DS3 / DS4).
The Status LED associated with that downstream port
glows blue. Copy the 2-GB le from the ash drive to
the PC / laptop to transfer data in USB 3.0 mode
7
Step 7: Demonstrating Battery Charging
• Connect an Apple device or a USB battery charging
v1.2 compliant device to a Standard USB 3.0
downstream port or a Shared Link USB 2.0 port to
charge the device.
Note: Battery charging is not supported on the
Shared Link SS downstream ports
Step 6: Demonstrating SS and USB 2.0 Data Transfer on
the Shared Link ports
• Power off the board by disconnecting the AC-DC
adapter. Connect a USB 3.0 certied ash drive to a
Shared Link SS downstream port (DS1 / DS2). Power
on the board. Connect a USB 2.0certied ash drive to
a Shared Link USB 2.0 downstream port (DS1 / DS2)
Note 1: The board needs to be in powered off state
while connecting a device to any of the Shared Link SS
downstream ports as they are non-removable ports
Note 2: Status LED is not supported for the two
Shared Link USB 2.0 downstream ports
Note 3: USB 2.0 devices are not supported on
Shared Link SS downstream ports
• Copy a 2-GB le from the PC / laptop to both ash
drives. SS and USB 2.0 data transfer happen
simultaneously on the Shared Link downstream ports
Step 8: Demonstrating Ghost Charging
• Disconnect the USB cable from the upstream port to
detach the board from the PC / laptop. The device
connected to the downstream port continues to be
charged using the Ghost Charging™ feature
Note: When the USB cable is detached from the
upstream port, charging of the device stops
momentarily and resumes in 1-2 seconds
8
5
USB 3.0 ash
drive connected
to a Standard USB 3.0
downstream port (DS4)
Status LED for
DS4 (DS4_SS)
USB 2.0 ash drive
connected to a Shared Link
USB 2.0 downstream port
(DS1)
USB 3.0 ash drive
connected to a Shared Link
SS downstream port (DS1)
Battery charging
through a
standard USB 3.0
downstream port
6
CY4613 QUICK START GUIDE
Step 9: Conguring the HX3 Board for ACA-Dock
• Power Off the HX3 board and remove the USB 3.0
‘A to micro-B’ cable. Remove the devices connected on
the downstream ports
• Install jumper on pins 2 and 3 of J28. Also install
jumpers on pins 1 and 2 of J26 (PWR_HOST) and
J27 (RID). Note: The ACA-Dock feature is disabled by
default on CY4613 board while shipping from factory.
It has to be enabled using the above jumper settings
• Get a BC v1.2 compliant phone with OTG feature
(Host and Device functionality) such as Sony Xperia
(S/P/neo V). Get a USB 2.0 micro-B to micro-B cable
with ID pin connectivity. Connect one end of that cable
to HX3 board's USB 2.0 portion of the upstream port
as shown above
Note: To use ACA-Dock feature with Samsung Galaxy
Note 3, S3 and S4 devices, install jumper on pins 2
and 3 of J27
9
Step 12: Disabling the ACA-Dock Feature
• Power off the HX3 board. Disconnect the phone by
detaching the ‘micro-B to micro-B’ cable
• Install a jumper between pins 1 and 2 of J28. Remove
the jumpers on J26 (PWR_HOST) and J27 (RID)
1211
Step 10: Demonstrating Battery Charging on
Upstream Port
• Power the HX3 board by connecting the power supply
plug to the board’s DC supply jack
CAUTION: Make sure the phone is compliant to
BC v1.2 specication before using with the HX3 board.
Connecting a non-BC v1.2- compliant phone to the
board can damage or affect the phone functionality
as the board supplies VBUS on the upstream port
• Connect the other end of USB 2.0 ‘micro-B to micro-B’
cable to the phone as shown above
• The phone is charged by the upstream port using
HX3’s ACA-Dock feature
10
Step 11: Demonstrating Usage of Downstream Device
with Phone
• Connect a mouse to a Shared Link USB 2.0
downstream port (DS1 or DS2) or to a Standard
USB 3.0 downstream port (DS3 or DS4)
• The mouse is enumerated on the phone and the
on-screen cursor can be tracked using the mouse.
At the same time, the phone continues to get charged
by the board’s upstream port
USB 2.0 ‘micro-B to
micro-B’ cable connected
to USB 2.0 portion of the
upstream port
ACA-Dock
Conguration
Jumpers
(J26, J27 and J28)
Battery charging
as per BC v1.2
specication
USB 2.0
‘micro-B to
micro-B’ cable
connected to
the phone
Battery charging
status and mouse
cursor tracking
Mouse connected to
a standard USB 3.0
downstream port (DS3)
ACA-Dock jumper
settings for disabling
the ACA-Dock feature
HX3 USB 3.0 SHARED LINKTM HUB DEVELOPMENT KIT
CY4613 QUICK START GUIDE
Kit Operation: CY4613 is the development kit (DVK) for CYUSB3328-88LTXC, an advanced 4-port USB 3.0 Hub Controller from
Inneon supporting Shared Link and ACA-Dock features
The Shared Link feature allows each downstream USB 3.0 port
to be split into a SS port and a Standard USB 2.0 port.
CY4613 implements the Shared Link feature on two of the four
Standard USB 3.0 ports to support a total of six ports
(Two Standard USB 3.0 ports, two Shared Link SS ports and
two Shared Link USB 2.0 ports)
HX3's ACA-Dock feature enables charging of a BC v1.2-
compliant OTG host connected to the upstream port. HX3
on the CY4613 board controls the external power switch to
drive VBUS on the upstream port.
Operation of the DVK can be congured using a PC-based tool named BlasterPlus. More details about Shared Link, ACA-Dock
and the BlasterPlus tool can be found in the DVK user guide. To access the DVK user guide and the hardware design les,
download the 'CY4613HX3DVKSetup.exe’ le from www.inneon.com/cms/en/product/evaluation-boards/cy4613. Launch
the 'CY4613HX3DVKSetup.exe’ le and follow the steps in the installer window.
Standard
USB 3.0
Downstream
Port 3 (DS3, J21)
Shared Link SS
Downstream
Port 2
(DS2, J24)
Shared Link SS
Downstream
Port 1
(DS1, J29)
Port Status
Indicator LEDs
Pin Strap
Jumpers
Power LED (PWR)
12-V to 5-V
Regulator (U2)
12-V DC Supply Jack (J1)
Pin Strap Jumpers
HX3 (MPN:
CYUSB3328-88LTXC)
ACA-Dock Conguration
Jumpers (J26, J27 and J28)
Reset Switch
(SW1)
Standard USB 3.0
Downstream
Port 4 (DS4, J22)
Shared Link USB 2.0
Downstream Port 2 (DS2, J30)
Shared Link USB 2.0
Downstream Port 1 (DS1, J31)
Hub Suspend
Status LED (SUSP)
Conguration Mode
Select Jumpers
(J5 and J6)
USB3.0
Upstream
Port (J28)
Shared Link
SS DS2
Standard
USB 3.0
DS4
CY4613 Board Standard USB 3.0 DS3 USB 3.0 ports
split into SS ports
and standard
USB 2.0 ports
Shared Link
USB 2.0 DS2
Shared Link
USB 2.0 DS1
Shared Link
SS DS1
DS1
DS3
DS2
DS4
Overview of Shared Link VBUS supplied by
CY4613 to charge
the OTG host
Overview of ACA-Dock
Upstream
Port
VBUS
RID
HX3 Power
Switch
VBUS
Power
Source
Enable
Power
CY4613 Board
Doc.# 001-91548 Rev.*C
Published by Inneon Technologies AG Am Campeon 1-15, 85579 Neubiberg Germany
© 2023 Inneon Technologies AG. All Rights Reserved. Date: 10 / 2023
www.inneon.com
/