LIGHT MY BRICKS 10211 Operating instructions

Here is the instructions document for the Lego Grand Emporium LED lighting kit.

Please read and follow the steps carefully to ensure this lighting kit is installed

properly.

Package contents:

6x White Strip Lights

14x White 30cm Bit Lights 

Light My Bricks : Grand Emporium LED Lighting

Kit

1x 12-port Expansion Board

1x 8-port Expansion Board

1x Lamp Post with LED and cable attached

8x Adhesive squares

5x LEGO Plates 1×6 (for mounting strip lights)

1x Battery Pack (requires 3x AA Batteries)

OR

1x USB Power Cable

Note – Battery Pack will be replaced with USB Power Cables from mid April

2020

Connecting Cables

2x 5cm cable

3x 15cm cable

2x 30cm cable

Important things tonote:

Laying cables in between and underneath bricks

Cables can t in between and underneath LEGO® bricks, plates, and tiles providing

they are laid correctly between the LEGO® studs. Do NOT forcefully join LEGO®

together around cables; instead ensure they are laying comfortably in between each

stud.



Connecting cable connectors to StripLights

Take extra care when inserting connectors to ports on the Strip Lights. Connectors

can be inserted only one way. With the Strip Light facing up, ensure the side of the

connector with the wires exposed is facing down. If a plug won’t t easily into a port

connector, don’t force it. Doing so will damage the plug and the connector.

CAUTION: Forcing LEGO® to connect over a cable can result in damaging

the cable andlight.

“



Connecting cable connectors to Expansion Boards



Take extra care when inserting connectors to ports of Expansion Boards. Connectors

can be inserted only one way. With the expansion board facing up, look for the

soldered “=” symbol on the left side of the port. The connector side with the wires

exposed should be facing toward the soldered “=” symbol as you insert into the port.

If a plug won’t t easily into a port connector, do not force it.

WARNING: Incorrectly inserting the connector can result in bent pins inside the

port or possible overheating of the expansion board when connected.



Installing Bit Lights under LEGO® bricks andplates.

When installing Bit Lights under LEGO® pieces, ensure they are placed the correct

way up (Yellow LED component exposed). You can either place them directly on top

of LEGO® studs or in between.



OK, Let’sBegin!



Instructions for installing thiskit

1.) This lighting kit is installed from the bottom up. Start by removing the 2nd and

top levels of the modular building.



2.) To enable us to lay the cable for the lamp post underneath the brick tiles, remove

the stock lamp post and mail box, as well as the following tiles as per below.



3.) Replace the stock lamp post with the Light My Bricks lamp post ensuring that the

cable is laid in the middle of the 2 studs facing toward the right of the building.

Gently bend the base plate down and lift the building of the ground oor up so we

can thread the cable for the lamp post underneath the building wall.



Pull the cable all the way up from the inside of the building underneath the wall and

then use some sticky tape to secure the cable to the wall and to prevent it from

being seen from the outside looking in.



4.) Ensure the lamp post cable is laid neatly in between the Lego studs before

reconnecting the tiles we removed earlier, followed by the mail box.



5.) We will now light up the lamps on the sides as well as two green shades. First

remove the following Lego pieces to allow us access.



6.) Remove one of the pillars and then disconnect the top 2 layers. Disconnect the

lamp and disassemble it as per below.



7.) Take 1x Bit Light and thread the connector end through the top whole of the

black brick and out through the bottom end. Pull it all the way through until the LED

reaches the end and then secure it in place by reconnecting the trans yellow piece.



8.) Reattach the lamp with bit light installed onto the pillar ensuring the cable is laid

in between the 2 black Lego studs, then reconnect the top two layers of the pillar.



Page is loading ...

LIGHT MY BRICKS 10211 Operating instructions

LIGHT MY BRICKS 10211 Operating instructions

Related papers

Other documents