ESAB EMP 285ic 1PH and 3PH User manual

Category
Welding System
Type
User manual
MANUAL PART # 0463 620 001 © ESAB AB 2017
Valid for: serial nos. 745-xxx-xxxx, 747-xxx-xxxx
Rights
reserved
to alter specifications without
notice.
SERVICE MANUAL
EMP 285ic 1PH and 3PH
(Intentionally Blank)
CAUTION
These INSTRUCTIONS are for experienced operators. If you are not fully familiar with the
principles of operation and safe practices for arc welding and cutting equip
ment, we urge
you to read our booklet, "Precautions and Safe Practices for Arc
Welding, Cutting, and
Gouging," Form 52-529. See:
http://www.esabna.com/eu/literature/precautions%20and%20safe%20practices%20fo
r%20arc%20welding,%20cutting%20and%20gouging.pdf
Do NOT permit untrained persons to install, operate, or maintain this equipment. Do NOT
attempt to install or operate this equipment until you have read and fully understand
these instructions. If you do not fully understand these instructions, contact your supplier
for further information. Be sure to read the Safety Precautions before installing or
operating this equipment.
CAUTION
These INSTRUCTIONS are for experienced operators. If you are not fully familiar with the
principles of operation and safe practices for arc welding and cutting equip
ment, we urge
you to read our booklet, "Precautions and Safe Practices for Arc
Welding, Cutting, and
Gouging," Form 52-529. See:
http://www.esabna.com/literature/precautions%20and%20safe%20practices%20for%20a
rc%20welding,%20cutting%20and%20gouging.pdf
Do NOT permit untrained persons to install, operate, or maintain this equipment. Do NOT
attempt to install or operate this equipment until you have read and fully understand
these instructions. If you do not fully understand these instructions, contact your supplier
for further information. Be sure to read the Safety Precautions before installing or
operating this equipment.
WARNING
Before use, read and understand the instruction and follow all
labels, employer’s safety practices and Safety Data Sheets.
(Intentionally Blank)
i
SECTION TABLE OF CONTENTS
Paragraph Page
SECTION 1 WELCOME TO ESAB
1.1 HOW TO USE THIS MANUAL ................................................................................... I
1.2 EQUIPMENT IDENTIFICATION ................................................................................. I
1.3
RECEIPT OF EQUIPMENT ......................................................................................... I
1.4 DESCRIPTION .......................................................................................................... I
SECTION 2 SAFETY
2.1 MEANING OF SYMBOLS ...................................................................................... 2-1
2.1.1 SAFETY GUIDANCE AND INFORMATION ............................................................ 2-1
2.1.2 SAFETY PRECAUTIONS ...................................................................................... 2-1
2.1.3 FIRES AND EXPLOSIONS .................................................................................... 2-3
2.1.4 ELECTRICAL SHOCK ........................................................................................... 2-4
2.1.5 ELECTRIC AND MAGNETIC FIELDS ..................................................................... 2-4
2.1.6 FUMES AND GASES ........................................................................................... 2-5
2.1.7 CYLINDER HANDLING ........................................................................................ 2-6
2.1.8 MOVING PARTS ................................................................................................ 2-7
2.1.9 MALFUNCTION ................................................................................................. 2-7
2.1.10 EQUIPMENT MAINTENANCE ............................................................................. 2-7
2.1.11 FALLING EQUPMENT ........................................................................................ 2-8
2.1.12 ARC RAYS .......................................................................................................... 2-8
2.1.13 NOISE ............................................................................................................... 2-8
2.1.14 USER RESPONSIBILITY ....................................................................................... 2-9
2.2 ESD (ELECTROSTATIC DISCHARGE) .................................................................... 2-11
SECTION 3 INTRODUCTION
3.1 KEY FEATURES ..................................................................................................... 3-1
3.2 EQUIPMENT ........................................................................................................ 3-1
3.2.1 EMP 285ic 1ph.................................................................................................. 3-1
3.2.2 EMP 285ic 3ph:................................................................................................. 3-2
3.3 OVERHEATING PROTECTION ............................................................................... 3-2
SECTION 4 TECHNICAL SPECIFICATIONS
4.1 EMP 285IC (1PH) SPECIFICATIONS ...................................................................... 4-1
4.2 EMP 285IC (3PH) SPECIFICATIONS ...................................................................... 4-4
SECTION 5 INSTALLATION
5.1 LOCATION ........................................................................................................... 5-1
ii
SECTION TABLE OF CONTENTS
Paragraph Page
5.2 HIGH FREQUENCY INTERFERENCE ....................................................................... 5-2
5.2.1 User’s Responsibility......................................................................................... 5-3
5.2.2 Assessment of Area .......................................................................................... 5-3
5.3 LIFTING INSTRUCTIONS ....................................................................................... 5-4
5.4 MAIN SUPPLY...................................................................................................... 5-5
5.5 RECOMMENDED ELECTRICAL-SUPPLY SPECIFICATIONS ...................................... 5-6
5.6 SUPPLY FROM POWER GENERATORS ................................................................. 5-7
SECTION 6 OPERATION
6.1 UNIT’S CONNECTIONS AND CONTROLS .............................................................. 6-2
6.2 CONNECTION OF WELDING AND RETURN CABLES .............................................. 6-3
6.2.1 FOR MIG/MMA PROCESS .................................................................................. 6-3
6.2.2 FOR TIG PROCESS ............................................................................................. 6-4
6.3 POLARITY CHANGE .............................................................................................. 6-4
6.4 SHIELDING GAS ................................................................................................... 6-4
6.5 VOLT-AMPERE CURVES ....................................................................................... 6-5
6.5.1 1ph VOLT-AMPERE CURVES .............................................................................. 6-5
6.5.1.1 SMAW (Stick) 120 V, 1ph ............................................................................... 6-5
6.5.1.2 SMAW (Stick) 230 V, 1ph ............................................................................... 6-5
6.5.1.3 GMAW (MIG) 120 V, 1ph ............................................................................... 6-6
6.5.1.4 GMAW (MIG) 230 V, 1ph ............................................................................... 6-6
6.5.1.5 GTAW (TIG) 120 V, 1ph .................................................................................. 6-7
6.5.1.6 GTAW (TIG) 230 V, 1ph .................................................................................. 6-7
6.5.2 3ph VOLT-AMPERE CURVES .............................................................................. 6-8
6.5.2.1 SMAW (Stick) 460 V, 3ph / SMAW (Stick) 575 V, 3ph ..................................... 6-8
6.5.2.2 GMAW (MIG) 460 V, 3ph / GMAW (MIG) 575 V, 3ph ..................................... 6-8
6.5.2.3 GTAW (TIG) 460 V, 3ph / GTAW (TIG) 575 V, 3ph ........................................... 6-9
6.6 DUTY CYCLE....................................................................................................... 6-10
6.7 REMOVING/INSTALLING BOBBIN ..................................................................... 6-13
6.8 REMOVING/INSTALLING WIRE .......................................................................... 6-15
6.8.1 REMOVING WIRE ............................................................................................ 6-16
6.8.2 INSTALLLING WIRE ......................................................................................... 6-19
6.9 WELDING WITH ALUMINUM WIRE ................................................................... 6-20
6.10 SETTING WIRE-FEED PRESSURE ......................................................................... 6-21
6.11 REMOVING/INSTALLING WIRE-FEED ROLLERS .................................................. 6-23
6.11.1 REMOVING WIRE-FEED ROLLERS .................................................................... 6-24
6.11.2 INSTALLING WIRE-FEED ROLLERS .................................................................... 6-26
6.12 REMOVING/INSTALLING/ADJUSTING WIRE-FEED GUIDES ................................ 6-28
6.12.1 OUTPUT WIRE-GUIDE REMOVAL/INSTALLATION ............................................ 6-32
iii
SECTION TABLE OF CONTENTS
Paragraph Page
6.12.2 CENTER WIRE-GUIDE REMOVAL/INSTALLATION ............................................. 6-32
6.12.3 ADJUSTING WIRE GUIDES ............................................................................... 6-32
SECTION 7 CONTROL PANEL
7.1 HOW TO NAVIGATE ............................................................................................ 7-1
7.2 MAIN MENU ....................................................................................................... 7-1
7.3 SMIG MODE: BASIC ............................................................................................. 7-2
7.4 SMIG MODE: ADVANCED .................................................................................... 7-2
7.5 MANUAL MIG MODE: BASIC ............................................................................... 7-3
7.6 MANUAL MIG MODE: ADVANCED ...................................................................... 7-3
7.7 FLUX CORED WIRE MODE: BASIC ........................................................................ 7-4
7.8 FLUX CORED WIRE MODE: ADVANCED ............................................................... 7-4
7.9 MMA MODE: BASIC ............................................................................................ 7-5
7.10 MMA MODE: ADVANCED ................................................................................... 7-5
7.11 LIFT-TIG MODE: BASIC ........................................................................................ 7-6
7.12 LIFT-TIG MODE: ADVANCED................................................................................ 7-6
7.13 SETTINGS ............................................................................................................ 7-7
7.14 USER MANUAL INFORMATION ........................................................................... 7-7
7.15 ICON REFERENCE GUIDE ...................................................................................... 7-8
SECTION 8 MAINTENANCE
8.1 ROUTINE MAINTENANCE .................................................................................... 8-2
8.2 WIRE-FEEDER ASSEMBLY MAINTENANCE .......................................................... 8-2
8.2.1 WIRE-FEEDER ASSEMBLY CLEANING ................................................................. 8-2
8.3 EMP-UNIT POWER-SIDE MAINTENANCE ............................................................. 8-5
8.4 TORCH LINER MAINTENANCE ............................................................................. 8-5
8.4.1 TORCH LINER CLEANING ................................................................................... 8-5
SECTION 9 TROUBLESHOOTING 3-PHASE UNIT
9.1 POWER-SUPPLY SIDE THEORY OF OPERATION ................................................... 9-1
9.1.1 Structure of the Power-Supply Side .................................................................. 9-2
9.1.2 Design structure of the Power Supply Circuit .................................................... 9-3
9.1.3 Working Principle of the Power Supply Side Sub-Assemblies ............................ 9-3
9.2 PRELIMINARY FUNCTIONAL CHECKS ................................................................... 9-5
9.3 SUBASSEMBLY DESCRIPTION, LOCATION, TEST POINTS, REMOVAL ................... 9-7
9.3.1 Access into the Power Side ............................................................................... 9-7
9.3.2 User Interface (UI) ............................................................................................ 9-7
9.3.2.1 UI Disassembly .............................................................................................. 9-9
iv
SECTION TABLE OF CONTENTS
Paragraph Page
9.3.2.2 User Interface (UI) Software-Displayed Fault Codes ..................................... 9-10
9.4 POWER-SUPPLY SIDE INTERNAL LED (LIGHT EMITTING DIODE) DIAGNOSTICS . 9-11
9.4.1 Main Power Switch, SW1 ................................................................................ 9-11
9.4.2 EMI Filter Board ............................................................................................. 9-13
9.4.2.1 EMI Filter Board Disassembly....................................................................... 9-15
9.4.3 Main Power Board .......................................................................................... 9-15
9.4.3.1 Main Power Board Disassembly ................................................................... 9-18
9.4.4 Internal Power Supply (IPS) Board .................................................................. 9-20
9.4.4.1 IPS Board Disassembly ................................................................................. 9-22
9.4.5 Control Board ................................................................................................. 9-23
9.4.5.1 DIP Switch Settings ...................................................................................... 9-25
9.4.5.2 Control Board Disassembly .......................................................................... 9-28
9.4.6 Main Transformer .......................................................................................... 9-28
9.4.7 Output Diode Assembly .................................................................................. 9-30
9.4.7.1 Output Diode Board Disassembly ................................................................ 9-32
9.4.8 Output Inductor ............................................................................................. 9-32
9.4.9 Current Sensor ............................................................................................... 9-34
9.4.10 Cooling Fans ................................................................................................... 9-35
9.4.11 Gas Valves ...................................................................................................... 9-36
9.5 FUNCTIONAL TEST PROCEDURES ...................................................................... 9-37
9.5.1 Initial Set up conditions .................................................................................. 9-37
9.6 POWER UP TEST ................................................................................................ 9-38
9.6.1 POWER-UP TEST PROBLEMS ........................................................................... 9-40
9.7 SMAW PROCESS TEST ....................................................................................... 9-42
9.7.1 SMAW Process Test: LED status ...................................................................... 9-42
9.7.2 SMAW PROCESS TEST PROBLEMS ................................................................... 9-43
9.8 GTAW LIFT TIG PROCESS TEST .......................................................................... 9-44
9.8.1 GTAW LIFT TIG Process Test: LED status ......................................................... 9-44
9.8.2 GTAW LIFT TIG PROCESS TEST PROBLEMS ...................................................... 9-45
9.9 GMAW MIG PROCESS TEST ............................................................................... 9-46
9.9.1 GMAW Process Test: LED status ..................................................................... 9-46
9.9.2 GMAW PROCESS TEST PROBLEMS .................................................................. 9-47
9.10 COMPONENT, SUB-ASSEMBLY TESTS................................................................ 9-49
9.10.1 Power Cord/Plug, Power Switch, and EMI Board Test ..................................... 9-49
9.10.2 Primary Rectifier Test ..................................................................................... 9-51
9.10.2.1 BR1, BR2 Test Procedure ............................................................................. 9-53
9.10.3 IPS Board Test ................................................................................................ 9-55
9.10.4 Main Power Board Test .................................................................................. 9-57
9.10.5 Control Board Test ......................................................................................... 9-61
v
SECTION TABLE OF CONTENTS
Paragraph Page
9.10.6 UI Board Test .................................................................................................. 9-65
9.10.7 D67-D69/D174-D177 Output Diode Board Test .............................................. 9-67
9.10.7.1 Output Diode Board External Test ............................................................... 9-67
9.10.7.2 Output Diode Board Internal Test ................................................................ 9-68
9.10.8 Current Sensor Test ........................................................................................ 9-69
9.10.9 Remote Control Trigger Test ........................................................................... 9-70
SECTION 10 TROUBLESHOOTING 1-PHASE UNIT
10.1 1-PHASE UNIT: POWER-SUPPLY SIDE OPERATION ............................................ 10-1
10.1.1 Structure of the Power-Supply Side ................................................................ 10-1
10.1.2 1-Phase Unit: Design structure of the Power Supply Circuit ............................ 10-2
10.1.3 1-Phase Unit: Working Principle of the Power Supply Side Sub-Assemblies .... 10-3
10.2 PRELIMINARY FUNCTIONAL CHECKS ................................................................. 10-5
10.3 SUBASSEMBLY DESCRIPTION, LOCATION, TEST POINTS, REMOVAL ................. 10-8
10.3.1 User Interface (UI) .......................................................................................... 10-8
10.3.1.1 UI Disassembly ............................................................................................ 10-9
10.3.1.2 User Interface (UI) Software-Displayed Fault Codes ................................... 10-10
10.3.2 Main Power Switch, SW1 .............................................................................. 10-11
10.3.3 Main Power Board ........................................................................................ 10-12
10.3.3.1 Main Power Board Disassembly ................................................................. 10-16
10.3.4 Control Board ............................................................................................... 10-18
10.3.4.1 DIP Switch Settings .................................................................................... 10-20
10.3.4.2 Control Board Disassembly ........................................................................ 10-23
10.3.5 Main Transformer ........................................................................................ 10-23
10.3.6 Output Diode Assembly ................................................................................ 10-25
10.3.6.1 Output Diode Board Disassembly .............................................................. 10-26
10.3.7 Output Inductor ........................................................................................... 10-27
10.3.8 Current Sensor ............................................................................................. 10-29
10.3.9 Cooling Fans ................................................................................................. 10-30
10.3.10 Gas Valves .................................................................................................... 10-31
10.4 FUNCTIONAL TEST PROCEDURES .................................................................... 10-32
10.4.1 Power-UP Procedure .................................................................................... 10-32
10.4.1.1 Power-Up Faults ........................................................................................ 10-34
10.4.2 SMAW Process Test ...................................................................................... 10-36
10.4.2.1 SMAW Process Test: LED status ................................................................. 10-36
10.4.2.2 SMAW Process Test Problems ................................................................... 10-37
10.4.3 GTAW LIFT TIG Process Test ......................................................................... 10-38
10.4.3.1 GTAW LIFT TIG Process Test: LED status .................................................... 10-38
10.4.3.2 GTAW LIFT TIG Process Test Problems ....................................................... 10-39
vi
SECTION TABLE OF CONTENTS
Paragraph Page
10.4.4 GMAW MIG Process Test .............................................................................. 10-40
10.4.4.1 GMAW Process Test Problems ................................................................... 10-41
10.5 COMPONENT, SUB-ASSEMBLY TESTS.............................................................. 10-43
10.5.1 Initial Set up conditions ................................................................................ 10-43
10.5.2 MAIN POWER CABLE/PLUG Test ................................................................... 10-44
10.5.3 SW1, ON/OFF SWITCH Test ........................................................................... 10-45
10.5.4 VR1, VARISTOR on POWER BOARD Test ........................................................ 10-46
10.5.5 BR1/BR2, BRIDGE RECTIFIERS ON POWER-BOARD ........................................ 10-47
10.5.6 PTC1 (R79)/RELAY (RY1) CONTACTS IN PARALLEL ON POWER BOARD Test ... 10-47
10.5.7 D49, D50 DIODES/Q19, Q21/C35-38 on POWER BOARD Test ....................... 10-48
10.5.8 Q3, Q4, Q6; Q7 SWITCHING TRANSISTORS on POWER BOARD Test ................ 10-50
10.5.9 D67-D69/D174-D177 Output Diode Board Test ............................................ 10-52
10.5.9.1 Output Diode Board External Test ............................................................. 10-52
10.5.9.2 Output Diode Board Internal Test .............................................................. 10-53
10.5.10 Main Power Board Test ................................................................................ 10-54
10.5.11 Control Board Test ....................................................................................... 10-56
10.5.12 UI Board Test ................................................................................................ 10-60
10.5.13 Current Sensor Test ...................................................................................... 10-62
10.5.14 Remote Control Trigger Test ......................................................................... 10-63
10.6 CALIBRATION (FOR BOTH 3 PH AND 1 PH) ...................................................... 10-64
SECTION 11 ORDERING SPARE PARTS
11.1 SPARE PARTS .................................................................................................... 11-1
11.2 WEAR PARTS ..................................................................................................... 11-3
11.3 ACCESSORIES .................................................................................................... 11-4
11.4 REPLACEMENTS PARTS ..................................................................................... 11-5
vii
(Intentionally Blank)
viii
SECTION LIST OF FIGURES
Figure Page
Figure 2-1. Danger and Warning Symbols ............................................................................ 2-1
Figure 5-1. Minimum Safe Clearances .................................................................................. 5-1
Figure 5-2. Lifting Illustrated ................................................................................................ 5-4
Figure 5-3. Sloping Ground .................................................................................................. 5-4
Figure 5-4. Rating plate (1) with supply connection data ..................................................... 5-6
Figure 6-1. Front & Rear Views: Model EMP 285ic ............................................................... 6-2
Figure 6-2. Function of User Interface Control Dials............................................................. 6-3
Figure 6-3. SMAW (Stick) 120 V, 1ph ................................................................................... 6-5
Figure 6-4. SMAW (Stick) 230 V, 1ph ................................................................................... 6-5
Figure 6-5. GMAW (MIG), 120 V, 1 ph.................................................................................. 6-6
Figure 6-6. GMAW (MIG) 230 V, 1ph ................................................................................... 6-6
Figure 6-7. GTAW (TIG) 120 V, 1ph ...................................................................................... 6-7
Figure 6-8. GTAW (TIG) 230 V, 1ph ...................................................................................... 6-7
Figure 6-9. SMAW (Stick) 460 V, 3ph / SMAW (Stick) 575 V, 3ph ......................................... 6-8
Figure 6-10. GMAW (MIG) 460 V, 3ph / GMAW (MIG) 575 V, 3ph ....................................... 6-8
Figure 6-11 GTAW (TIG) 460 V, 3ph / GTAW (TIG) 575 V, 3ph .............................................. 6-9
Figure 6-12. Example of 40 % Duty Cycle ........................................................................... 6-10
Figure 6-13. Example of 50 % Duty Cycle ........................................................................... 6-10
Figure 6-14. Plotting Duty Cycle for 120 V, 1ph AC ............................................................. 6-11
Figure 6-15. Plotting Duty Cycle for 230 V, 1ph AC ............................................................. 6-11
Figure 6-16 Plotting Duty Cycle for 460 V or 575 V, 3ph AC ............................................... 6-12
Figure 6-17 Tightening the Bobbin Locking Nut (A) for 100 mm (4 in.) .............................. 6-13
Figure 6-18. Tightening the Bobbin Locking Nut (A) for 200 mm (8 in.), 300 mm (12 in.) ... 6-14
Figure 6-19. View of Wire-Bobbin-Side .............................................................................. 6-15
Figure 6-20. Wire-Bobbin Side Exposed View..................................................................... 6-16
Figure 6-21. Wire-Feed Mechanism ................................................................................... 6-17
Figure 6-22. Holding Knob for Torch Adapter ..................................................................... 6-18
Figure 6-23. Check Feed-Roller for Slip, Indicating no Over-pressure ................................. 6-21
Figure 6-24. Checking for Proper Feed-Roller Pressure ...................................................... 6-22
Figure 6-25. Location of Wire-Feed Rollers and Pressure Rollers........................................ 6-23
Figure 6-26. Wire-Feed Mechanism ................................................................................... 6-24
Figure 6-27. Drive Gear with Woodruff Key on Motor Shaft............................................... 6-25
ix
SECTION LIST OF FIGURES
Figure Page
Figure 6-28. Feed Roller Removal and Installation ............................................................. 6-25
Figure 6-29. Wire-Feed Rollers Offered in Multiple Sizes ................................................... 6-26
Figure 6-30. Location of Wire-Guides and Their Set Screws ............................................... 6-29
Figure 6-31. Wire Guides ................................................................................................... 6-30
Figure 6-32. Wire-Feed Mechanism ................................................................................... 6-31
Figure 6-33. Verify Clearance of Both Guide Tubes ............................................................ 6-33
Figure 8-1. Tension Arm & Wire-Feed Cover on Wire-Feed Assembly .................................. 8-3
Figure 9-1. EMP 3-Phase Unit’s Power Supply Side .............................................................. 9-1
Figure 9-2. 3-Phase Power Supply Side Assemblies .............................................................. 9-2
Figure 9-3. 3-Phase Power Supply Circuit Functional Block Diagram .................................... 9-4
Figure 9-4. Power-Side Cover Removal ................................................................................ 9-7
Figure 9-5. User Interface (UI) ............................................................................................. 9-8
Figure 9-6. Connector Location on UI board ........................................................................ 9-8
Figure 9-7. UI Structure ....................................................................................................... 9-9
Figure 9-8. Location of Mounting Screws for UI ................................................................... 9-9
Figure 9-9. Main Power Switch, SW1, Functional Location ................................................. 9-11
Figure 9-10. Main Power Switch, SW!, Connection Labels.................................................. 9-12
Figure 9-11. Main Power Switch, SW1, 3 ph....................................................................... 9-12
Figure 9-12. Location of EMI Filter Board ........................................................................... 9-13
Figure 9-13. EMI Filter Board Map ..................................................................................... 9-14
Figure 9-14. EMI Filter Functional Location ........................................................................ 9-14
Figure 9-15. EMI Board Disassembly .................................................................................. 9-15
Figure 9-16. Location of Main Power Board ....................................................................... 9-16
Figure 9-17. Location of Primary Rectifier, BR1, BR2 .......................................................... 9-16
Figure 9-18. Main Power Board Map ................................................................................. 9-17
Figure 9-19. Main Power Board (3ph) Functional Location................................................. 9-18
Figure 9-20. Heat Sink Support Bracket ............................................................................. 9-19
Figure 9-21. Main Power Supply Board Disassembly .......................................................... 9-19
Figure 9-22. Location of Internal Power Supply (IPS) Board ............................................... 9-20
Figure 9-23. Internal Power Supply (IPS) Board Map .......................................................... 9-21
Figure 9-24. IPS Board Functional Location ........................................................................ 9-22
Figure 9-25. IPS Board Disassembly ................................................................................... 9-22
x
SECTION LIST OF FIGURES
Figure Page
Figure 9-26. Location of Control Board .............................................................................. 9-23
Figure 9-27. Control Board LED Locations .......................................................................... 9-24
Figure 9-28. DIP Switch Settings on Control Board ............................................................. 9-25
Figure 9-29. Control Board Functional Location ................................................................. 9-26
Figure 9-30. Control Board Connector Locations................................................................ 9-27
Figure 9-31. Control Board Disassembly ............................................................................ 9-28
Figure 9-32. Location of Main Transformer ........................................................................ 9-29
Figure 9-33. Main Transformer Functional Location .......................................................... 9-29
Figure 9-34. Location of Output Diode Assembly ............................................................... 9-30
Figure 9-35. Map of Output Diode Board ........................................................................... 9-31
Figure 9-36. Output Diode Assembly Functional Location .................................................. 9-31
Figure 9-37. Output Diode Board Disassembly ................................................................... 9-32
Figure 9-38. Location of Output Inductor ........................................................................... 9-33
Figure 9-39. Output Inductor Functional Location ............................................................. 9-33
Figure 9-40. Location of Current Sensor ............................................................................. 9-34
Figure 9-41. Current Sensor Functional Location ............................................................... 9-34
Figure 9-42. Location of Cooling Fans ................................................................................ 9-35
Figure 9-43. Cooling Fans Functional Location ................................................................... 9-35
Figure 9-44. Gas Valves...................................................................................................... 9-36
Figure 9-45. Power-Side Cover Removal ............................................................................ 9-37
Figure 9-46. Control Board LED Locations .......................................................................... 9-39
Figure 9-47. Test Points for Control Board CN10 ................................................................ 9-47
Figure 9-48. Test Points for Control Board CN13 ................................................................ 9-48
Figure 9-49 Test Points on IPS Board for Continuity to Plug Blades ................................... 9-50
Figure 9-50. Test Point Schematic for Continuity ............................................................... 9-50
Figure 9-51. Location of BR 1 and BR 2 on Main Power Board ........................................... 9-51
Figure 9-52. Pin Identification for BR1, BR2 ....................................................................... 9-52
Figure 9-53. Schematic of BR1 or BR2 ................................................................................ 9-53
Figure 9-54. Terminal Identification of BR 1, BR 2 .............................................................. 9-54
Figure 9-55. IPS Board Test Points ..................................................................................... 9-56
Figure 9-56. Location of VR1 on Main Power Board ........................................................... 9-57
Figure 9-57. Test Points for Rl79, RY1 ................................................................................ 9-58
xi
SECTION LIST OF FIGURES
Figure Page
Figure 9-58. Test Points for C70, C72, C400 ....................................................................... 9-59
Figure 9-59. Test Points for Q3, Q4, Q6, Q7 ....................................................................... 9-60
Figure 9-60. SW2 Switch Positions ..................................................................................... 9-61
Figure 9-61. Test Points for Control Board CN19 ................................................................ 9-62
Figure 9-62. Test Points for Control Board CN17 ................................................................ 9-62
Figure 9-63. Test Points for Control Board CN18 ................................................................ 9-63
Figure 9-64. Test Points for Control Board CN13 ................................................................ 9-63
Figure 9-65. CN10 Test Points ............................................................................................ 9-64
Figure 9-66. Pinout of CN6 on Control Board ..................................................................... 9-66
Figure 9-67. UI CN3 to Control Board CN6 Connector Locations ........................................ 9-66
Figure 9-68. Reference Figure for Steps 1 & 2 .................................................................... 9-67
Figure 9-69. Diode Output Test Procedure Illustrated ........................................................ 9-68
Figure 9-70. CN18 Test Points ............................................................................................ 9-69
Figure 9-71. Remote Control Connector, J1 Pinout Diagram .............................................. 9-70
Figure 10-1. EMP 1-Phase Unit’s Power Supply Side .......................................................... 10-1
Figure 10-2. 1-Phase Power Supply Side Assemblies .......................................................... 10-2
Figure 10-3. 1-Phase Power Supply Circuit Functional Block Diagram 1 ph ........................ 10-4
Figure 10-4. User Interface (UI) ......................................................................................... 10-8
Figure 10-5. Connector Location on UI board .................................................................... 10-8
Figure 10-6. UI Structure ................................................................................................... 10-9
Figure 10-7. Location of Mounting Screws for UI ............................................................... 10-9
Figure 10-8. Location of Main Power Switch, SW1 ........................................................... 10-11
Figure 10-9. Main Power Switch, SW1, Functional Location ............................................. 10-11
Figure 10-10. Main Power Switch, SW1 ........................................................................... 10-12
Figure 10-11. Location of BR1, BR2 and Main Power Board ............................................. 10-13
Figure 10-12. Location of Select Components .................................................................. 10-14
Figure 10-13. 1 ph Main Power Board Map ..................................................................... 10-15
Figure 10-14. Main Power Board (1ph) Functional Location ............................................. 10-16
Figure 10-15. Location of Left, Baffle Support Bracket ..................................................... 10-16
Figure 10-16. 1 ph Main Power Supply Board Fastener Locations ..................................... 10-17
Figure 10-17. Location of Control Board .......................................................................... 10-18
Figure 10-18. Control Board LED Locations ...................................................................... 10-19
xii
SECTION LIST OF FIGURES
Figure Page
Figure 10-19. DIP Switch Settings on Control Board ......................................................... 10-20
Figure 10-20. Control Board Functional Location ............................................................. 10-21
Figure 10-21. Control Board Connector Locations ............................................................ 10-22
Figure 10-22. Control Board Disassembly ........................................................................ 10-23
Figure 10-23. Location of Main Transformer .................................................................... 10-24
Figure 10-24. Main Transformer Functional Location....................................................... 10-24
Figure 10-25. Location of Output Diode Assembly ........................................................... 10-25
Figure 10-26. Output Diode Assembly Functional Location .............................................. 10-25
Figure 10-27. Map of Output Diode Board ....................................................................... 10-26
Figure 10-28. Output Diode Board Disassembly ............................................................... 10-27
Figure 10-29. Location of Output Inductor ....................................................................... 10-28
Figure 10-30. Output Inductor Functional Location.......................................................... 10-28
Figure 10-31. Location of Current Sensor ......................................................................... 10-29
Figure 10-32. Current Sensor Functional Location ........................................................... 10-29
Figure 10-33. Location of Cooling Fans ............................................................................ 10-30
Figure 10-34. Cooling Fans Functional Location ............................................................... 10-31
Figure 10-35. Gas Valves .................................................................................................. 10-31
Figure 10-36. Control Board LED Locations ...................................................................... 10-33
Figure 10-37. Test Points for Control Board CN10 ............................................................ 10-41
Figure 10-38. Test Points for Control Board CN13 ............................................................ 10-42
Figure 10-39. Reference Figure for Steps 1a, 1b, 1c ......................................................... 10-44
Figure 10-40. Reference Figure for SW1, ON/OFF SWITCH ............................................... 10-45
Figure 10-41. Reference Figure for VR1 ........................................................................... 10-46
Figure 10-42. Reference Figure for PTC1/RV1 .................................................................. 10-47
Figure 10-43. Reference Figure for D49, D50 DIODES/Q19, Q21/C35-38 .......................... 10-49
Figure 10-44. Reference Figure for Q3, Q4, Q6; Q7 .......................................................... 10-51
Figure 10-45. Reference Figure for D67-D69/D174-D177 ................................................. 10-52
Figure 10-46. Diode Output Test Procedure Illustrated .................................................... 10-53
Figure 10-47. Reference Figure for Main Power Board Test ............................................. 10-54
Figure 10-48. Reference for Step 3a and 3b ..................................................................... 10-55
Figure 10-49. SW2 Switch Positions ................................................................................. 10-56
Figure 10-50. Test Points for Control Board CN19 ............................................................ 10-57
xiii
SECTION LIST OF FIGURES
Figure Page
Figure 10-51. Test Points for Control Board CN13 ............................................................ 10-57
Figure 10-52. CN 10 Test Voltage Measurement .............................................................. 10-58
Figure 10-53. Test Points for Control Board CN17 ............................................................ 10-58
Figure 10-54. Test Points for Control Board CN18 ............................................................ 10-59
Figure 10-55. Pinout of CN6 on Control Board ................................................................. 10-61
Figure 10-56. UI CN3 to Control Board CN6 Connector Locations ..................................... 10-61
Figure 10-57. CN 18 Test Measurements ......................................................................... 10-62
Figure 10-58. Remote Control Connector, J1 Pinout Diagram .......................................... 10-63
Figure 11-1. Unit-Part Example .......................................................................................... 11-2
Figure 11-2. Wire-Feed Assembly, Wear-Parts ................................................................... 11-3
xiv
(Intentionally Blank)
xv
SECTION LIST OF TABLES
Table Page
Table 4-1. Specifications for EMP 285ic 1ph ........................................................................ 4-1
Table 4-2. Specifications for EMP 285ic 3ph ........................................................................ 4-4
Table 5-1. Recommended Electrical-Supply Specifications: 1 ph, 50/60 Hz .......................... 5-6
Table 5-2. Recommended Electrical-Supply Specifications 3 ph, 50/60 Hz ........................ 5-7
Table 8-1. Maintenance Schedule During Normal Conditions .............................................. 8-2
Table 9-1. 3-Phase Power Supply Side Assemblies ............................................................... 9-2
Table 9-2. Table of Faults ..................................................................................................... 9-5
Table 9-3. UI Fault Codes ................................................................................................... 9-10
Table 9-4. Control Board LED Meanings ............................................................................. 9-25
Table 9-5. BR1, BR2 Test Procedure ................................................................................... 9-54
Table 10-1. 1-Phase Power Supply Side Assemblies ........................................................... 10-2
Table 10-2. Table of Faults ................................................................................................. 10-5
Table 10-3. UI Fault Codes ............................................................................................... 10-10
Table 10-4. Control Board LED Meanings ......................................................................... 10-20
Table 11-1. Unit Part Numbers .......................................................................................... 11-2
Table 11-2. Reference for Figure 10-2 Wire-Feed Assembly, Wear-Parts ........................... 11-3
Table 11-3. Accessories ..................................................................................................... 11-4
Table 11-4. Replacement Part # ......................................................................................... 11-5
xvi
(Intentionally Blank)
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8
  • Page 9 9
  • Page 10 10
  • Page 11 11
  • Page 12 12
  • Page 13 13
  • Page 14 14
  • Page 15 15
  • Page 16 16
  • Page 17 17
  • Page 18 18
  • Page 19 19
  • Page 20 20
  • Page 21 21
  • Page 22 22
  • Page 23 23
  • Page 24 24
  • Page 25 25
  • Page 26 26
  • Page 27 27
  • Page 28 28
  • Page 29 29
  • Page 30 30
  • Page 31 31
  • Page 32 32
  • Page 33 33
  • Page 34 34
  • Page 35 35
  • Page 36 36
  • Page 37 37
  • Page 38 38
  • Page 39 39
  • Page 40 40
  • Page 41 41
  • Page 42 42
  • Page 43 43
  • Page 44 44
  • Page 45 45
  • Page 46 46
  • Page 47 47
  • Page 48 48
  • Page 49 49
  • Page 50 50
  • Page 51 51
  • Page 52 52
  • Page 53 53
  • Page 54 54
  • Page 55 55
  • Page 56 56
  • Page 57 57
  • Page 58 58
  • Page 59 59
  • Page 60 60
  • Page 61 61
  • Page 62 62
  • Page 63 63
  • Page 64 64
  • Page 65 65
  • Page 66 66
  • Page 67 67
  • Page 68 68
  • Page 69 69
  • Page 70 70
  • Page 71 71
  • Page 72 72
  • Page 73 73
  • Page 74 74
  • Page 75 75
  • Page 76 76
  • Page 77 77
  • Page 78 78
  • Page 79 79
  • Page 80 80
  • Page 81 81
  • Page 82 82
  • Page 83 83
  • Page 84 84
  • Page 85 85
  • Page 86 86
  • Page 87 87
  • Page 88 88
  • Page 89 89
  • Page 90 90
  • Page 91 91
  • Page 92 92
  • Page 93 93
  • Page 94 94
  • Page 95 95
  • Page 96 96
  • Page 97 97
  • Page 98 98
  • Page 99 99
  • Page 100 100
  • Page 101 101
  • Page 102 102
  • Page 103 103
  • Page 104 104
  • Page 105 105
  • Page 106 106
  • Page 107 107
  • Page 108 108
  • Page 109 109
  • Page 110 110
  • Page 111 111
  • Page 112 112
  • Page 113 113
  • Page 114 114
  • Page 115 115
  • Page 116 116
  • Page 117 117
  • Page 118 118
  • Page 119 119
  • Page 120 120
  • Page 121 121
  • Page 122 122
  • Page 123 123
  • Page 124 124
  • Page 125 125
  • Page 126 126
  • Page 127 127
  • Page 128 128
  • Page 129 129
  • Page 130 130
  • Page 131 131
  • Page 132 132
  • Page 133 133
  • Page 134 134
  • Page 135 135
  • Page 136 136
  • Page 137 137
  • Page 138 138
  • Page 139 139
  • Page 140 140
  • Page 141 141
  • Page 142 142
  • Page 143 143
  • Page 144 144
  • Page 145 145
  • Page 146 146
  • Page 147 147
  • Page 148 148
  • Page 149 149
  • Page 150 150
  • Page 151 151
  • Page 152 152
  • Page 153 153
  • Page 154 154
  • Page 155 155
  • Page 156 156
  • Page 157 157
  • Page 158 158
  • Page 159 159
  • Page 160 160
  • Page 161 161
  • Page 162 162
  • Page 163 163
  • Page 164 164
  • Page 165 165
  • Page 166 166
  • Page 167 167
  • Page 168 168
  • Page 169 169
  • Page 170 170
  • Page 171 171
  • Page 172 172
  • Page 173 173
  • Page 174 174
  • Page 175 175
  • Page 176 176
  • Page 177 177
  • Page 178 178
  • Page 179 179
  • Page 180 180
  • Page 181 181
  • Page 182 182
  • Page 183 183
  • Page 184 184
  • Page 185 185
  • Page 186 186
  • Page 187 187
  • Page 188 188
  • Page 189 189
  • Page 190 190
  • Page 191 191
  • Page 192 192
  • Page 193 193
  • Page 194 194
  • Page 195 195
  • Page 196 196
  • Page 197 197
  • Page 198 198
  • Page 199 199
  • Page 200 200
  • Page 201 201
  • Page 202 202
  • Page 203 203
  • Page 204 204
  • Page 205 205
  • Page 206 206
  • Page 207 207
  • Page 208 208
  • Page 209 209
  • Page 210 210
  • Page 211 211
  • Page 212 212
  • Page 213 213
  • Page 214 214
  • Page 215 215
  • Page 216 216
  • Page 217 217
  • Page 218 218
  • Page 219 219
  • Page 220 220
  • Page 221 221
  • Page 222 222
  • Page 223 223
  • Page 224 224
  • Page 225 225
  • Page 226 226
  • Page 227 227
  • Page 228 228
  • Page 229 229
  • Page 230 230
  • Page 231 231
  • Page 232 232
  • Page 233 233
  • Page 234 234
  • Page 235 235
  • Page 236 236
  • Page 237 237
  • Page 238 238
  • Page 239 239
  • Page 240 240
  • Page 241 241
  • Page 242 242
  • Page 243 243
  • Page 244 244
  • Page 245 245
  • Page 246 246
  • Page 247 247
  • Page 248 248

ESAB EMP 285ic 1PH and 3PH User manual

Category
Welding System
Type
User manual

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI