Danfoss Self-limiting Heating Cables Operating instructions

Brand: Danfoss

Model: Self-limiting Heating Cables

Type: Operating instructions

Danfoss Self-limiting Heating Cables enable you to accomplish a wide range of tasks, including:

Preventing frost and ice buildup on roofs and in gutters
Protecting pipes from freezing
Maintaining the temperature of hot water supplies

These cables are self-regulating, meaning that they automatically adjust their heat output based on the ambient temperature. This prevents overheating and ensures energy efficiency while providing reliable protection against freezing.

Installation is straightforward, thanks to the included accessories and clear instructions. The cables can be cut to length, making them suitable for a variety of applications.

Danfoss Self-limiting Heating Cables enable you to accomplish a wide range of tasks, including:

Preventing frost and ice buildup on roofs and in gutters
Protecting pipes from freezing
Maintaining the temperature of hot water supplies

Installation is straightforward, thanks to the included accessories and clear instructions. The cables can be cut to length, making them suitable for a variety of applications.

MAKING MODERN LIVING POSSIBLE

Installation Guide

Danfoss Self-limiting Heating Cables

SLPG-10/26/33, SLPG-18, SLHW-55/70, SLPH-10

www.EH.danfoss.com

Table of Contents

1 Introduction ............................................. 3

1.1 Self-limiting Heating Cables ................................. 4

1.2 Safety Instructions ...................................... 4

1.3 Handling ............................................ 5

1.4 System Overview ....................................... 6

1.5 Functional Overview ..................................... 6

2 Installation in General ....................................... 7

2.1 Fastening Methods ...................................... 7

2.2 Calculating C-C Distance ................................... 7

2.3 Calculating Cable Length .................................. 8

2.4 Max. Cable Length ...................................... 8

2.5 Planning the Installation ................................... 9

2.6 Preparing the Installation Area ............................... 9

3 Installing Heating Elements .................................... 9

3.1 Installing Elements ...................................... 10

4 Application .............................................. 11

4.1 Installation on Pipes ..................................... 11

4.2 Installation in pipes ...................................... 13

4.3 Installation Inside the Pipe ................................. 14

4.4 Installing on Roof and Gutters ............................... 14

5 Finalizing the Installation ..................................... 15

5.1 Connecting a Thermostat .................................. 16

1 Introduction

In this installation manual, the word “element” refers

to heating cables.

For other applications please contact your local sales

office.

Frost protection of roof and gutter systems Frost protection of pipe systems

- see section 4.4 - see section 4.1, 4.2, 4.3

Installation Guide Danfoss Self-limiting Heating Cables

Danfoss Heating Solutions VIAMQ202

1.1 Self-limiting Heating Cables

Introduction

The heating cables are used mainly for ice and snow

melting on roofs and in gutters, down pipes, for frost

protection of pipes and for temperature maintenance

of the hot-water supply.

There are 4 types of Danfoss self-limiting heating ca-

bles with various effects depending on the applica-

tion.

Cable Construction

Self-limiting heating cables are designed with a tem-

perature dependant resistant element between two

parallel copper bus wires.

When the bus wires are connected to the mains, a

current goes through the temperature dependant re-

sistant element which will then heat. As the element

is heated the resistance value rises causing the cur-

rent to decline and heating is reduce. This explains

the self-limiting effect.

The regulation of the output takes place independ-

ently on the entire length of the cable according to

the actual ambient temperature.

If the ambient temperature rises the heating effect of

the cable is reduced. Due to this self-limiting capabili-

ty, overheating of the cable can be avoided, also if

two heating cables are touching or crossing.

As self-limiting heating cables always gives off a cer-

tain amount of effect, it is recommended to connect

the heating cable to a thermostat to be able to dis-

connect the current when heating is not required.

Due to the parallel power supply the heating cable

can be shortened anywhere. This simplifies the plan-

ning and installation.

1. Outer sheath

2. Screen

3. Insulation

4. Self-limiting heating element

5. Bus wires

1.2 Safety Instructions

Never cut or shorten the heating element

▪

Cutting the heating element will void the war-

ranty.

▪

Cold leads and mat mesh can be cut or short-

ened to suit requirements, only.

Installation Guide Danfoss Self-limiting Heating Cables

VIAMQ202 Danfoss Heating Solutions

Elements must always be installed according to lo-

cal building regulations and wiring rules as well as

the guidelines in this installation manual

▪

Any other installation may hamper element

functionality or constitute a safety risk, and will

void the warranty.

▪

Make sure that elements, cold leads, connection

boxes, and other electrical components do not

come into contact with chemicals or flammable

materials during or after installation.

Elements must always be connected by an author-

ised electrician using a fixed connection.

▪

De-energize all power circuits before installation

and service.

▪

The connection to the power source must not

be directly accessible to the end user.

▪

Each heating cable screen must be earthed in

accordance with local electricity regulations and

connected to a residual current device (RCD).

▪

Recommended RCD trip rating is 30 mA, but

may be up to 300 mA where capacitive leakage

may lead to nuisance tripping.

▪

Heating elements must be connected via a

switch providing all pole disconnection.

▪

The element must be equipped with a correctly

sized fuse or circuit breaker, e.g. 10/13 A for a

1.5 mm

cold lead and 16/20 A for a 2.5 mm

cold lead.

Pipe Tracing

▪

Sensor

▪

Heating Cable

▪

Insulation

▪

Fitting

▪

Valve

The presence of a heating element must

▪

be made evident by affixing caution signs or

markings at the power connection fittings

and/or frequently along the circuit line where

clearly visible.

▪

be stated in any electrical documentation fol-

lowing installation.

Never exceed the maximum heat density (W/m)

for the actual application.

1.3 Handling

▪

If the heating cable is delivered on a cable drum

you should use a reliable holder for the drum

when unrolling the cable.

▪

Pull the heating cable straight of the drum.

▪

Avoid pulling violently, breaking or squeezing

the heating cable.

▪

Do not place the heating cable over sharp ob-

jects or edges.

Installation Guide Danfoss Self-limiting Heating Cables

Danfoss Heating Solutions VIAMQ202

▪

The heating cable must be protected against ex-

cess strain and tension. Stepping on the cables

or crossing the cables with vehicles should be

avoided, as this may damage the cables.

▪

The surface onto which the cable is to be instal-

led must be clean and free of sharp objects.

▪

Never secure the cable with metal or metal

strips.

▪

Do not connect power to heating cable while it

is on the drum or shipping carton.

1.4 System Overview

Cable Color Application Effect Dimension Cap Mechanical Class

SLPG-10 Blue On pipes

10W/m @ 10

5,5 x 11,5 mm Polyolefin UV IEC 60800:M2

SLPG-26 Red On pipes

25W/m @ 10

5,5 x 11,5 mm Polyolefin UV IEC 60800:M2

SLPG-33 Grey On pipes

33W/m @ 10

5,5 x 11,5 mm Polyolefin UV IEC 60800:M2

SLPG-18 Black Roof & gutter

18W/m @ 10

5,8 x 11,3 mm Polyolefin UV IEC 60800:M2

SLPG-18 Black Roof & gutter

18W/m @ 10

5,8 x 11,3 mm Polyolefin UV IEC 60335-2-96

SLHW-55 Green On pipes

8W/m @ 55

5,8 x 11,8 mm Polyolefin UV IEC 60800:M2

SLHW-70 Red On pipes

12W/m @ 70

5,8 x 11,8 mm Polyolefin UV IEC 60800:M2

SLPH-10 Blue On / in pipes

10W/m @ 10

5,3 x 7,7 mm Thermoplastic IEC 60800:M2

SLPH-10 Blue On / in pipes

10W/m @ 10

5,3 x 7,7 mm Thermoplastic IEC 60335-2-96

Voltage 220V - 240V AC

Minimum installation temperature -5° C.

Max. temperature ON = 65° C.

Max. temperature OFF = 85° C.

Note:

▪

The stated effect is measured on the cable in-

stalled on pipe under insulation.

▪

The Self-limiting cables have to be in good ther-

mal contact with the item to be heated.

▪

When self-limiting cables are surrounded by

thermal conducting materials (water / concrete,

etc.) the effect may be double in relation to the

nominal value.

1.5 Functional Overview

1. Element

2. C-C distance

3. Cold lead connection

4. Cold lead

5. Connection box (if any)

6. Sensor

7. Thermostat

Installation Guide Danfoss Self-limiting Heating Cables

VIAMQ202 Danfoss Heating Solutions

2 Installation in General

2.1 Fastening Methods

Danfoss Aluminium Tape

For ensuring efficient heat transfer.

Spaceclip

For attaching cables and relieving from sharp edges.

2.2 Calculating C-C Distance

For areas on roofs the C-C distance is the distance in

centimetres from the centre of one cable to the cen-

tre of the next.

C-C =

Area [m

]

x 100 cm

Cable length [m]

C-C = Cable output [W/m] x 100 cm

Heat density [W/m

]

The max. C-C distance for roof and gutter systems is

10 cm.

W/m² @ 220V/380V

C-C [cm] 20 W/m 25 W/m 30 W/m

5 366 457 -

7,5 244 305 366

10 183 229 274

W/m² @ 230V/400V

C-C [cm] 20 W/m 25 W/m 30 W/m

5 400 500 -

7,5 267 333 400

10 200 250 300

W/m² @ 240V/415V

C-C [cm] 20 W/m 25 W/m 30 W/m

5 436 544 -

7,5 290 363 436

10 218 272 327

SLPG-18

C-C [cm] 220V/380V 230V/400V 240V/415V

329 W/m

360 W/m

392 W/m

7,5

219 W/m

240 W/m

262 W/m

165 W/m

180 W/m

196 W/m

Installation Guide Danfoss Self-limiting Heating Cables

Danfoss Heating Solutions VIAMQ202

2.3 Calculating Cable Length

Please consider all of the below when calculating the

length of the heating cable:

▪

Heated pipe length

▪

Number of connections x 0,3 m heating cable.

▪

Number of specials x 0,5 m heating cable.

▪

Number of T-derivations x 1 m heating cable.

▪

Heating cable length for flanges, fittings and

measured pipe extensions.

2.4 Max. Cable Length

SLPG-10 SLPG-26 SLPG-33

Max. heating cable length at 230 V

FUSE FUSE FUSE

Temperature 10A 16A 20A 10A 16A 20A 10A 16A 20A

-30° C 50 m 120 m 150 m 30 m 45 m 64 m 22 m 43 m 52 m

-15° C 70 m 139 m 186 m 40 m 58 m 75 m 25 m 49 m 64 m

0° C 85 m 165 m 190 m 50 m 75 m 85 m 32 m 60 m 70 m

10° C 120 m 205 m 205 m 65 m 88 m 117 m 40 m 70 m 90 m

SLPG-18 SLHW-55 SLHW-70

Max. heating cable length at 230 V

FUSE FUSE FUSE

Temperature 10A 16A 20A 10A 16A 20A 10A 16A 20A

-30° C 40 m 77 m 106 m - - - - - -

-15° C 60 m 93 m 125 m - - - - - -

0° C 80 m 110 m 135 m - - - - - -

10° C 105 m 145 m 162 m 70 m 88 m 117 m 60 m 80 m 90 m

SLPH-10 (on pipe) SLPH-10 (in pipe)

Max. heating cable length at 230 V

FUSE FUSE

Temperature 10A 16A 10A 16A

-30° C 50 m 54 m - -

-15° C 79 m 85 m - -

0° C 96 m 103 m - -

10° C 100 m 107 m 60 m 60 m

Installation Guide Danfoss Self-limiting Heating Cables

VIAMQ202 Danfoss Heating Solutions

2.5 Planning the Installation

Draw a sketch of the installation which shows

▪

element layout

▪

cold leads and connections

▪

junction box/cable well (if applicable)

▪

sensor

▪

connection box

▪

thermostat

Save the sketch

▪

Knowing the exact location of these compo-

nents makes subsequent troubleshooting and

repair of faulty elements easier.

Bear in mind the following:

▪

Observe correct C-C distance (heating cables

only) - see section 2.2.

▪

Observe required installation depth and possi-

ble mechanical protection of cold leads.

▪

When installing more than one element, never

wire elements in series but route all cold leads

in parallel to the connection box.

2.6 Preparing the Installation Area

▪

Remove all traces of old installations, if applica-

ble.

▪

Ensure that the installation surface is even, sta-

ble, smooth, dry and clean.

▪

If necessary, fill out gaps around pipes,

drains, or walls or apply foil covering

▪

There must be no sharp edges, leaves, dirt or

foreign objects.

3 Installing Heating Elements

It is not recommended to install elements at tempera-

tures below -5 °C.

At low temperatures, heating cables can become rig-

id. After rolling out the element, briefly connect it to

the mains supply to soften the cable before fastening.

Measuring Resistance

Measure, verify and record element resistance during

installation.

▪

After unpacking

▪

After fastening the elements

▪

After the installation in finalized

Also measure if there is connection between the two

conductors or from the conductor to the metal

sheath.

Installation Guide Danfoss Self-limiting Heating Cables

Danfoss Heating Solutions VIAMQ202

If the insulation resistance is not as labelled, the ele-

ment must be replaced.

▪

Check for short circuits by measuring between

the two bus wires and the screen.

3.1 Installing Elements

The heating cables bending diameter must not be

less than 25 mm (32 mm for SLPG-18). The cable must

only be bended on the flat side.

For reduction of electricity consumption, we strongly

recommend that it is possible to switch off the heat-

ing cable, i.e. by using a ECtemp thermostat.

After installation the cable insulation resistance must

be measured and recorded.

At low temperatures the heating cable can become

stiff and difficult to work with. This problem can be

solved by connecting the unreeled cable to the mains

for a brief period of time.

Installation Guide Danfoss Self-limiting Heating Cables

VIAMQ202 Danfoss Heating Solutions

4 Application

4.1 Installation on Pipes

Frost protection of pipe systems [W/m]

Δt [K] Insulation [mm] Pipe diameter DN [mm]

15 20 25 32 40 50 65 80 100 125 150 200

10 8 9 11 14 16 19 24 29 36 44 - -

20 5 6 7 8 9 11 14 16 19 24 28 36

30 4 5 5 6 7 8 10 12 14 17 19 25

40 4 4 5 5 6 7 8 9 11 13 15 19

50 3 4 4 5 5 6 7 8 9 11 13 16

10 12 14 17 20 24 29 37 44 - - - -

20 8 9 10 12 14 17 20 24 29 35 42 -

30 6 7 8 9 11 12 15 18 21 25 29 37

40 5 6 7 8 9 10 12 14 17 20 23 29

50 5 6 6 7 8 9 11 12 14 17 19 24

10 15 19 22 27 32 39 49 - - - - -

20 10 12 14 16 19 22 27 32 39 47 - -

30 8 9 11 12 14 17 20 23 28 33 39 50

40 7 8 9 10 12 14 16 19 22 26 31 39

50 6 7 8 9 10 12 14 16 19 22 26 32

Pipe tracing

1. Sensor.

2. Heating cable.

3. Insulation.

4. Fitting.

5. Valve.

Installation Guide Danfoss Self-limiting Heating Cables

Danfoss Heating Solutions VIAMQ202

The self-limiting heating cable may only be used for

installations with pipes of metal or plastic.

When installing heating cables on plastic pipes:

▪

Place a strip of aluminium tape on the pipe.

▪

Place the heating cable on the aluminium tape.

▪

Secure the heating cables with aluminum tape.

It is recommended that the entire cable is covered

with aluminum tape, to ensure efficient heat transfer

to the plastic pipe.

The cable must be placed optimal on the 5 or 7

o'clock position of the pipe, thus mechanical strain of

the heating cable is prevented when e.g. the insula-

tors are working along the pipe.

There must always be as much insulation as possible

on the pipe to reduce the heat loss.

WARNING!

230V AC HEATING CABLE

▪

When the heating cable is installed on pipes,

the insulation should be clearly marked with a

warning.

Installation on Special Flanges and Pumps

▪

Always observe the minimum tolerable bending

diameter of 25 mm (32 mm for SLPG-18)!

▪

Heating cables on specials, valves etc. should al-

ways be positioned so that they are easily as-

sessable and replaceable in connection with in-

spection and repair and so that it will not be

necessary to cut them! You can avoid this prob-

lem when there is sufficient cable wrapped in a

spiral around the specials.

Installation Guide Danfoss Self-limiting Heating Cables

VIAMQ202 Danfoss Heating Solutions

1. Valve

2. Heating cable

3. Aluminium tape

4. Pipe

5. Pipe fitting

Installation Summary

Straight cables must be fitted as shown at 5 or 7 o'clock. In-

pipe cables are fitted directly in the pipe with compression

gland. Cables wrapped around pipes are attached as shown

for every 20-30 cm of pipe with aluminium tape (for large

pipe diameters only).

Extend cold leads/terminate cables, and place

connections in a dry place. Mount connection

box on or close to pipe, and install thermostat

next to pipe.

4.2 Installation in pipes

In-pipe Frost Protection

1. Insulation.

2. Heating cable.

3. Sensor (optional - not shown).

4. Fitting.

Installation Guide Danfoss Self-limiting Heating Cables

Danfoss Heating Solutions VIAMQ202

▪

Installation of SLPH in pipes is energy-saving,

because the heating cable is in direct contact

with the fluid that is to be heated.

▪

Do not use the heating cable in pipes with inlet

water pressure above 1 MPa (10 bar). Please

note that in this case the heating cable must be

connected via a fault current relay (RCD), and it

must be possible to disconnect the heating ca-

ble.

▪

Never install the heating cable in taps and

valves.

▪

Never switch on power, before the pipe is filled.

▪

If the heating cable is damaged during installa-

tion, it must be replaced.

▪

When the heating cable is installed in pipes, the

pipe or insulation should be clearly marked with

a warning.

WARNING!

230V AC HEATING CABLE

4.3 Installation Inside the Pipe

1. Fit a T-shaped pipe of a generous size over the

pipe.

2. Fit the wadding (the item with male thread) in-

side the T-shaped pipe.

3. Push the heating cable through the wadding,

using lubricant to facilitate the installation. The

connection between heating cable and con-

necting cable must be outside the wadding.

4. Mount the Wadding in the following sequence:

▪

Mount the nut with the flat side facing the

connection.

▪

Mount the washer on the heating cable.

▪

Squeeze the rubber seal on the heating

cable.

5. Mount the male threaded part with the female

threaded part facing the end of the cable.

6. The heating cable must extended straight

through the T-shaped pipe.

7. Turn the wadding until it fits tightly

8. Insulate the pipe with at least 30 mm insulation

or more if required.

4.4 Installing on Roof and Gutters

1. Roof edge / eave

2. Gutter

3. Downpipe to frost-free well

4. Gutter valley

5. Flat roof with drain

6. Roof with baffles

7. Downpipe with open end

To provide sufficient heat in gutters, the heat density

and the number of cable lines, depends on the design

temperature and the gutter diameter.

Installation Guide Danfoss Self-limiting Heating Cables

VIAMQ202 Danfoss Heating Solutions

Design temperature Heat density Cable lines C-C

°C

[W/m

]

[No.] [cm]

0 to -5 200 - 250 1 8-9

-6 to -15 250 - 300 2 7

-16 to -25 300 - 350 2 6

-26 to -35 350 - 400 3 4-5

We recommend that you always use a controller for controlling the self-limiting heating cables to avoid waste

of energy.

Inform the end user to check for and remove sharp

edges, leaves, and dirt from the heated roof and gut-

ter systems every autumn.

5 Finalizing the Installation

Connecting cables

▪

Connect all cold leads and the sensor to the

connection box.

▪

See the installation manual for the thermostat.

Final check and documentation

▪

Make sure that the heat distributor (e.g. roof,

pipe) can withstand the heat from the element.

This is particularly important if the element is

connected to a thermostat that does not allow

configuration of maximum temperature - see

section 4.4.

▪

Document the following using text, drawings, or

photos:

▪

cable type, spacing, depth, layout, circuit

ID, sensors.

▪

location of connections between cold lead

and heating element.

▪

location of end caps (twin conductors

only).

▪

location of expansion joints, if any.

▪

Re-check and compare the insulation resistance.

Installation Guide Danfoss Self-limiting Heating Cables

Danfoss Heating Solutions VIAMQ202

Hand-over to the end user

▪

Instruct the end-user or the daily supervisor in

the operation and maintenance of the heating

system.

▪

Before every period of continuous use, check for

faults in the distribution board, thermostat, and

sensors.

5.1 Connecting a Thermostat

If the element is connected to a thermostat such as a

ECtemp, configure basic settings according to the ta-

ble below and as described in the thermostat installa-

tion manual.

If applicable, adjust the temperature limit in accord-

ance with the manufacturer’s recommendations in

order to prevent damage to e.g. the floor or the pipe.

▪

Note, however, that the limit must not exceed

the maximum temperature limit specified per

application (see section 4).

Thermostat Max. load

Frost protection of roof and gut-

ter systems

Frost protection of pipe systems

ECtemp 316 16 A -7 °C < On < +3 °C -

ECtemp 330/610 16/10 A On < +3 °C On < +5 °C

ECtemp 850 2 x 15A Melting < +3°C -

Installation Guide Danfoss Self-limiting Heating Cables

VIAMQ202 Danfoss Heating Solutions

Installation Guide Danfoss Self-limiting Heating Cables

Danfoss Heating Solutions VIAMQ202

Installation Guide Danfoss Self-limiting Heating Cables

VIAMQ202 Danfoss Heating Solutions

Installation Guide Danfoss Self-limiting Heating Cables

Danfoss Heating Solutions VIAMQ202

Installation Guide Danfoss Self-limiting Heating Cables

Danfoss A/S

Electric Heating Systems

Ulvehavevej 61

7100 Vejle

Denmark

Phone:+45 7488 8500

Fax: +45 7488 8501

Email: [email protected]

www.EH.danfoss.com

Danfoss can accept no responsibility for possible errors in catalogues, brochures and other printed material. Danfoss reserves the right to alter its products without notice. This also applies to products

already on order provided that such alterations can be made without subsequential changes being necessary in specifications already agreed. All trademarks in this material are property of the respective

Danfoss Self-limiting Heating Cables Operating instructions

Brand: Danfoss

Model: Self-limiting Heating Cables

Type: Operating instructions

Danfoss Self-limiting Heating Cables enable you to accomplish a wide range of tasks, including:

Preventing frost and ice buildup on roofs and in gutters
Protecting pipes from freezing
Maintaining the temperature of hot water supplies

Installation is straightforward, thanks to the included accessories and clear instructions. The cables can be cut to length, making them suitable for a variety of applications.

Download PDF

report

Danfoss Self-limiting Heating Cables Operating instructions

Danfoss Self-limiting Heating Cables Operating instructions

Related papers

Other documents