Projection Television
TOSHIBA CORPORATION, 2000
43H70
55H70
61H70
OWNER'S MANUAL
TM
Owner's Record
The model number and serial number are on the back
of your TV. Record these numbers in the spaces below.
Refer to these numbers whenever you communicate
with your Toshiba dealer about this TV.
Model number:
Serial number:
Introduction
Connecting
your TV
Using the
Remote Control
Setting up
your TV
Using the TV’s
Features
Appendix
Index
©
2
Important Information
WARNING
TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK, DO
NOT EXPOSE THIS APPLIANCE TO RAIN OR MOISTURE.
The lightning symbol in the triangle tells you that the
voltage inside this product may be strong enough to
cause an electric shock. DO NOT TRY TO SERVICE
THIS PRODUCT YOURSELF.
The exclamation mark in the triangle tells you that
important operating and maintenance instructions
follow this symbol.
CAUTION
TO PREVENT ELECTRIC SHOCK, DO NOT USE THIS
POLARIZED PLUG WITH AN EXTENSION CORD
RECEPTACLE OR OTHER OUTLET UNLESS THE
PRONGS CAN BE FULLY INSERTED INTO THE
OUTLET TO PREVENT ANY EXPOSURE OF THE
PRONGS ON THE POLARIZED PLUG.
ATTENTION
POUR PRÉVENIR LES CHOCS ÉLECTRIQUES NE PAS
UTILISER CETTE FICHE POLARISÉE AVEC UN
PROLONGATEUR, UNE PRISE DE COURANT OU UNE
AUTRE SORTIE DE COURANT, SAUF SI LES LAMES
PEUVENT ÊTRE INSÉRÉS À FOND SANS EN LAISSER
AUCUNE PARTIE À DÉCOUVERT.
CAUTION
The plug has one prong wider than the other and will fit only
one way into a standard
electrical outlet (120 volt AC,
60 Hz). If the plug does not
fit into the outlet, try turning
it around. If the plug still does
not fit, the outlet is probably
non-standard and must be
replaced by a qualified electrician. Do not tamper with the plug
or try to force it into a non-standard outlet.
Note to CATV system installers in the USA
This reminder is provided to call the CATV system installer’s
attention to Article 820-40 of the NEC, which provides
guidelines for proper grounding, and, in particular, specifies that
the cable ground shall be connected to the grounding system of
the building, as close to the point of cable entry as practical.
Precautions
Installing your TV
• Place the TV on the floor or on a sturdy platform. The
mounting surface should be flat and steady. If you install the
TV on a soft floor, make sure that the floor is not damaged
by the weight of the TV.
• Model 43H70 must be used only with the Toshiba stand
shown on page 44. Use with other stands may result in
instability and cause possible injury.
• Place the TV far enough away from the walls to allow proper
ventilation. This will prevent the TV from overheating and
avoid possible damage to the TV. Avoid dusty areas too.
• Damage may occur if you leave the TV in direct sunlight or
near a heater. Avoid areas subject to extremely high
temperatures or humidity, and temperatures of 41˚F(5˚C) or
lower.
Using your TV
• Do not stand or climb on the TV.
• Do not put any heavy object on top of the TV.
• Do not place containers with liquids such as drinks or
cosmetics on the TV. If any foreign material or water leaks
into the TV, unplug the AC cord and contact your dealer.
• If the room temperature suddenly rises, condensation may
occur on the lenses resulting in picture distortion or color
fading. In such a case, simply wait a while (with the power
on) and the condensation will evaporate.
• Avoid displaying stationary images on your TV screen for
extended periods of time. Stationary patterns generated by a
picture-in-picture (PIP) display, Multi-Window display,
computer displays, video games, stock market reports, etc.,
can become permanently engrained on the picture tube. This
damage is not protected by your warranty because it is the
result of misuse. If you wish to use your TV to display still
images, reduce brightness and contrast settings. Never leave a
PIP, Multi-Window, computer, or video game display
unattended.
• Sit approximately 10-25 feet away from the TV. Sitting too
far to the left or right of the screen will cause the picture to
appear dull as will direct sunlight and room lights. Turn the
TV off to check for reflections on the screen. Then remove
the source of any reflections while viewing.
Cleaning your TV
• Clean the TV with a soft, dry cloth. Never use strong solvents
such as thinner or benzine which might damage the finish of
the cabinet. If the cabinet is very dirty, use a damp cloth to
wipe the cabinet clean, then finish with a dry cloth.
wide prong
3
Introduction................................................................ 4
Welcome to Toshiba......................................................... 4
Exploring your new TV ................................................... 4
Connecting your TV .................................................. 5
Connecting a VCR .......................................................... 5
Connecting a cable converter box .................................... 6
Connecting a cable converter box and VCR ..................... 6
Connecting a DVD player or satellite receiver
and a VCR ....................................................................... 7
Connecting a DVD player (with or without
ColorStream™) and a VCR ............................................ 8
Connecting a DTV receiver/set-top box (with or
without ColorStream™) and a VCR ............................... 9
Connecting two VCRs ................................................... 10
Connecting a camcorder ................................................ 10
Connecting an audio system .......................................... 11
Connecting an A/V receiver ........................................... 11
Using the remote control ...................................... 12
Preparing the remote control for use .............................. 12
Installing the remote control batteries ............................ 12
Using the remote control with a VCR or
cable converter ............................................................... 12
Programming the remote control for use with a
VCR or cable TV converter ........................................... 13
VCR codes.............................................................. 13
Cable TV converter codes ....................................... 14
Learning about the remote control ................................. 15
Setting up your TV .................................................. 16
Learning about the menu system ................................... 16
Changing the on-screen display language ....................... 17
Selecting the antenna input............................................ 17
Using the TV/ VIDEO button on the TV .............. 17
Adding channels to the TV’s memory ............................ 18
Programming channels automatically ...................... 18
Adding and erasing channels manually.................... 19
Changing channels ........................................................ 19
Adjusting the color convergence..................................... 19
Using the TV’s features.......................................... 21
Adjusting the channel settings........................................ 21
Switching between two channels ............................. 21
Programming your favorite channels ....................... 21
Labeling channels ................................................... 22
Watching picture-in-picture (PIP).................................. 23
Switching the main and small pictures .................... 24
Changing the position of the small picture.............. 24
Freezing the small picture ....................................... 25
Using the Multi-Window feature ................................... 25
Using the preview function ..................................... 25
Using the favorite function ..................................... 25
Using the strobe function........................................ 26
Using the LOCKS menu ............................................... 26
Entering the PIN code ............................................ 26
Using the V-CHIP menu ............................................... 27
ENABLE BLOCKING .......................................... 27
TV RATING (Independent rating system for
broadcasters) ........................................................... 27
MPAA RATING (Independent rating system for
movies) ................................................................... 28
BLOCKING OPTION.......................................... 28
Unlocking programs temporarily ............................ 29
Locking channels ........................................................... 29
Locking video inputs ..................................................... 30
Changing the PIN code ................................................. 30
Adjusting the picture ..................................................... 31
Selecting the picture mode ...................................... 31
Adjusting the picture quality ................................... 31
Saving new preference ............................................. 32
Using the flesh tone feature ..................................... 32
Using the Digital Noise Reduction (DNR)
feature..................................................................... 32
Selecting the color temperature ............................... 33
Resetting your picture adjustments ......................... 33
Watching video input .................................................... 34
Selecting the 1080i picture size ...................................... 34
Selecting the video label ................................................. 35
Using the closed caption feature ..................................... 36
Setting the sleep timer.................................................... 37
Setting the clock ............................................................ 37
Adjusting the sound ....................................................... 38
Muting the sound ................................................... 38
Selecting stereo/SAP broadcasts .............................. 38
Using the
feature .................................... 39
Adjusting the sound quality .................................... 39
Resetting your audio adjustments ........................... 40
Using the sub-bass system (SBS) ............................. 40
Turning off the built-in speakers ............................. 41
Selecting the Audio OUT sound ............................. 41
Using the stable sound feature ................................ 42
Selecting the background of the menu display ............... 42
Displaying on-screen information .................................. 42
Viewing the demonstration mode .................................. 43
Understanding the auto power off feature ...................... 43
Understanding the last mode memory feature ................ 43
Appendix................................................................... 44
Specifications ................................................................. 44
Troubleshooting............................................................. 45
Limited United States Warranty ..................................... 46
Index .......................................................................... 47
Introduction
Connecting
your TV
Using the
Remote Control
Setting up
your TV
Using the TV’s
Features
Appendix
Index
4
Introduction
Welcome to Toshiba
Congratulations! You have purchased one of the finest projection TVs
on the market. The goal of this manual is to guide you through
setting up and operating your Toshiba TV as quickly as possible.
This manual applies to models 43H70, 55H70, and 61H70. Before
you start reading, check your model number by looking at the rear of
the TV.
Instructions in this manual are based on using the remote control.
You can also use the controls on the TV if they have the same name as
those on the remote control.
Please read all the safety and operating instructions carefully, and keep
the manual for future reference.
Exploring your new TV
You can operate your TV using the buttons on the front panel or the
remote control. The back panel and front panel (behind the door)
provide all the terminal connections you will need to connect other
equipment to your TV. See “Connecting your TV” on page 5.
VIDEO-3 IN
VIDEOS-VIDEO
AUDIO
L/MONO R
DEMO
MENU
VOLUME
TV/VIDEO
CHANNEL
POWER
MENU
VOL VOL
CH
CH
EXIT TV/VIDEO DEMO POWER
123
456
789
ENT
100
0
CH
VOL
POWER
TIMER
RECALL
TV/VIDEO
MUTE
TV
CABLE
VCR
CH RTN
STROBE
EXIT
LIGHT
STOP SOURCE
ADV/
PIP CH
ADV/
PIP CH
FAV
FAV
PLAY PIP
REC TV/VCR REW FF
STILL LOCATE SWAP
FAVORITE
MENU/
PREVIEW
ENTER
Video/Audio inputs
(Video 3)
POWER
Volume
x •
Channel
yz
DEMO
TV/
VIDEO
55H70
61H70
43H70
yz x •
Remote sensor
(Behind the screen panel)
Video/Audio inputs
(Video 3)
DEMO
MENU
TV/VIDEO
Volumex •
Channel zy
x •zy
POWER
Behind the door
Power indicator
Power indicator
Remote sensor
(Behind the screen panel)
MENU
EXIT
Please Note
On some models, the SET UP
menu automatically appears
on-screen the first time the
TV is turned on.
To change the menu settings,
see “Setting Up Your TV” on
page 16 for details.
To close the menu, either
press EXIT or turn the TV off.
Introduction
Connecting
your TV
Using the
Remote Control
Setting up
your TV
Using the TV’s
Features
Appendix
Index
5
Connecting your TV
If you have not connected electronic equipment before, or you have
been frustrated in the past, you may wish to read this section. (Cables
are not supplied.)
• A coaxial cable is the standard cable that comes in from your
antenna or cable converter box. Coaxial cables use “F”
connectors.
• Audio and video cables are usually color-coded according to use:
yellow for video and red and white for audio. The red audio cable
is for the stereo right channel, and the white audio cable is for
the stereo (or mono) left channel. If you look at the rear panel of
the TV, you will see that the terminals are color-coded in the
same manner as the cables.
• S-video cables provide better picture performance. S-video cables
can only be used with S-video compatible components.
• ColorStream™ cables come in sets of three and provide the best
picture performance. ColorStream cables can only be used with
ColorStream compatible components.
Connecting a VCR
This connection allows you to watch local channels and video
programs, play or record on the VCR while watching TV, and
record from one channel while watching another channel.
You will need:
• one coaxial cable
• one pair of audio cables (one single audio cable for a mono VCR)
• one video cable (one S-video cable for an S-VHS VCR)
Caution:
Do not plug the TV in until you have finished
connecting all of your equipment.
Note:
If you have a mono VCR, connect L/Mono to
VCR Audio OUT using only one audio cable.
If you have an S-VHS VCR, use the S-video
connections and remove the video cable.
Do not connect a regular video cable and an
S-video cable to Video-1 at the same.
ANTENNA
Coaxial Cable
AUDIO
Cables
VIDEO
Cable
S-VIDEO
Cable
Color Stream
Cable
ANT
(
75
)
ANT-1
CHANNEL IN
ON OFF
OUT
ANT-2
AUDIO CENTER
IN from ANT
VIDEO AUDIO
OUT to TV
CH 3
LR
CH 4
IN
OUT
OUT
RL
VAR
AUDIO
OUT
VIDEO
L/
MONO
IN
L
R
P
B
P
R
Y
L/
MONO
AUDIO
S-VIDEO
VIDEO
R
VIDEO-1 VIDEO-2
COLOR
STREAM
AUDIO
AUDIO
ININ
L
R
R
AUDIO
COLOR
STREAM
HD 2HD 1
P
B
P
R
Y
Stereo VCR
TV
From Cable or Antenna
Introduction
Connecting
your TV
Using the
Remote Control
Setting up
your TV
Using the TV’s
Features
Appendix
Index
6
Connecting a cable converter box
This connection allows you to watch basic and premium cable
channels.
To use the TV’s features, select ANT-1. To view premium channels,
select ANT-2, tune the TV to channel 3 or 4 (whichever channel is
vacant in your area), and use the converter box to change channels.
You will need:
• two coaxial cables
ANT
(
75
)
ANT-1
CHANNEL IN
ON OFF
OUT
ANT-2
AUDIO CENTER
INOUT
Cable converter box
OUT
RL
VAR
AUDIO
OUT
VIDEO
L/
MONO
IN
L
R
P
B
P
R
Y
L/
MONO
AUDIO
S-VIDEO
VIDEO
R
VIDEO-1 VIDEO-2
COLOR
STREAM
AUDIO AUDIO
ININ
L
R
R
AUDIO
COLOR
STREAM
HD 2HD 1
P
B
P
R
Y
TV From Cable
Connecting a cable converter box and VCR
This connection allows you to watch and record basic and premium
cable channels, watch videotapes, and record one channel while
watching another channel. To use the TV’s features, select ANT-1.
To view premium channels or record with the VCR, select ANT-2,
tune the TV to channel 3 or 4 (whichever channel is vacant in your
area), and use the converter box to change channels.
You will need:
• one two-way cable signal splitter
• three coaxial cables
• one pair of audio cables (one single audio cable for a mono VCR)
• one video cable (one S-video cable for an S-VHS VCR)
Note:
When you use a converter box with your TV,
the remote control will not operate some
features such as programming your favorite
channels, labeling channels, and locking
channels.
Note:
If you have a mono VCR, connect L/Mono to
VCR Audio OUT using only one audio cable.
If you have an S-VHS VCR, use an S-video
cable instead of a regular video cable. Do not
connect a regular video cable and an S-video
cable to Video-1 at the same time.
When you use a converter box with your TV,
the remote control will not operate some
features such as programming your favorite
channels, labeling channels, and locking
channels.
IN from ANT
VIDEO
AUDIO
OUT to TV
CH 3
LR
LR
CH 4
IN
OUT
OUT
IN
cable
converter box
ANT
(
75
)
ANT-1
CHANNEL IN
ON OFF
OUT
RL
OUT
VIDEO
VAR
AUDIO
L/
MONO
IN
DVD IN
L
R
C
R
C
B
Y
L/
MONO
AUDIO
R
S-VIDEO
VIDEO
OUT
ANT-2
AUDIO CENTER
VIDEO 1 VIDEO 2
COLOR
STREAM
INPUT
AUDIO
R
AUDIO
2-way
cable
signal
splitter
IN
OUT
OUT
From Cable
TV
Stereo VCR
Introduction
Connecting
your TV
Using the
Remote Control
Setting up
your TV
Using the TV’s
Features
Appendix
Index
7
Connecting a DVD player or satellite receiver
and a VCR
This connection allows you to watch DVD/satellite, VCR, and TV
programs, and record one TV channel while watching another
channel.
You will need:
• one coaxial cable
• two pairs of audio cables (one single and one pair of audio cables
for a mono VCR)
• one video cable (between the TV and VCR)
• one S-video cable (between the TV and DVD player/satellite
receiver)
Note:
For the highest possible picture quality from
a non-ColorStream DVD player/satellite
receiver, you must use an S-video cable
between the TV and DVD player/satellite
receiver. (If your DVD player or satellite
receiver is ColorStream-compatible, see
page 8).
Do not connect both an S-video cable and a
regular video cable between the TV and
DVD player/satellite receiver at the same
time. Doing so will distort the picture.
Do not connect the DVD player/satellite
receiver and VCR to the same video channel
on the TV. (See the illustrations, which show
the DVD player/satellite receiver connected to
Video-1 and the VCR connected to Video-2.)
Caution:
The unauthorized recording of television
programs, videotapes, and other materials
may infringe upon the provisions of copyright
laws.
OUT
RL
VAR
AUDIO
OUT
VIDEO
L/
MONO
IN
L
R
P
B
P
R
Y
L/
MONO
AUDIO
S-VIDEO
VIDEO
R
VIDEO-1 VIDEO-2
COLOR
STREAM
AUDIO
AUDIO
ININ
L
R
R
AUDIO
COLOR
STREAM
HD 2HD 1
P
B
P
R
Y
IN from ANT
VIDEO AUDIO
OUT to TV
CH 3
LR
CH 4
IN
OUT
IN from ANT
VIDEO
OUTOUT
S-VIDEO
AUDIO
OUT
L
R
ANT
(
75
)
ANT-1
CHANNEL IN
ON OFF
OUT
ANT-2
AUDIO CENTER
Stereo VCR
TV
Satellite Receiver
From
Satellite
Dish
From
Antenna
OUT
RL
VAR
AUDIO
OUT
VIDEO
L/
MONO
IN
L
R
P
B
P
R
Y
L/
MONO
AUDIO
S-VIDEO
VIDEO
R
VIDEO-1 VIDEO-2
COLOR
STREAM
AUDIO
AUDIO
ININ
L
R
R
AUDIO
COLOR
STREAM
HD 2HD 1
P
B
P
R
Y
IN from ANT
VIDEO AUDIO
OUT to TV
CH 3
LR
CH 4
IN
OUT
VIDEO
OUTOUT
S-VIDEO
AUDIO
OUT
L
R
ANT
(
75
)
ANT-1
CHANNEL IN
ON OFF
OUT
ANT-2
AUDIO CENTER
Stereo VCR
TV
DVD Player
From
Antenna
Introduction
Connecting
your TV
Using the
Remote Control
Setting up
your TV
Using the TV’s
Features
Appendix
Index
8
OUT
RL
VAR
AUDIO
OUT
VIDEO
L/
MONO
IN
L
R
P
B
P
R
Y
L/
MONO
AUDIO
S-VIDEO
VIDEO
R
VIDEO-1 VIDEO-2
COLOR
STREAM
AUDIO
AUDIO
ININ
L
R
R
AUDIO
COLOR
STREAM
HD 2HD 1
P
B
P
R
Y
IN from ANT
VIDEO AUDIO
OUT to TV
CH 3
LR
CH 4
IN
OUT
VIDEO
OUT
S-VIDEO
AUDIO
COMPONENT VIDEO
OUT
L
R
L
R
C
R
C
B
Y
ANT
(
75
)
ANT-1
CHANNEL IN
ON OFF
OUT
ANT-2
AUDIO CENTER
From
Antenna
Stereo VCR
TV
DVD Player with ColorStream™
Connecting a DVD player (with or without
ColorStream™) and a VCR
This connection allows you to watch DVD, VCR, and TV programs,
and record DVD and TV programs. You can record from one source
while watching a program from another source.
Your TV has ColorStream component video inputs. Connecting your
TV to a ColorStream-compatible DVD player (such as a Toshiba
ColorStream-equipped DVD player) can greatly enhance picture
quality and realism.
You will need:
• one coaxial cable
• three pairs of audio cables (two single and one pair of audio cables
for a mono VCR)
• two video cables
• one set of ColorStream video cables (one S-video cable for a
non-ColorStream DVD player; see notes at right)
Note:
For the highest possible picture quality, you
must use ColorStream video cables between
the TV and DVD player. You can connect the
ColorStream cables from the DVD player to
to either ColorStream jack on the TV (HD1 or
HD2).
If your DVD player is not ColorStream-
compatible, use the S-video connections
(both audio and video) instead of the
ColorStream connections. (Be aware,
however, that a ColorStream connection
provides higher picture quality than an
S-video connection.) Do not connect both
S-Video and ColorStream cables between the
TV and DVD player at the same time.
To record from the DVD player, set the VCR
to Line IN. To monitor recording from the
DVD player, set the VCR to Line IN, and set
the TV to Video-1.
Caution:
The unauthorized recording of television
programs, videotapes, and other materials
may infringe upon the provisions of copyright
laws.
Introduction
Connecting
your TV
Using the
Remote Control
Setting up
your TV
Using the TV’s
Features
Appendix
Index
9
OUT
RL
VAR
AUDIO
OUT
VIDEO
L/
MONO
IN
L
R
P
B
P
R
Y
L/
MONO
AUDIO
S-VIDEO
VIDEO
R
VIDEO-1 VIDEO-2
COLOR
STREAM
AUDIO
AUDIO
ININ
L
R
R
AUDIO
COLOR
STREAM
HD 2HD 1
P
B
P
R
Y
IN from ANT OUT to TV
CH 3
CH 4
VIDEO AUDIO
LR
IN
OUT
Satelite IN
VIDEO
OUT
S-VIDEO
AUDIO
OUT
L
R
L
R
C
R
C
B
Y
ANT
(
75
)
ANT-1
CHANNEL IN
ON OFF
OUT
ANT-2
AUDIO CENTER
COMPONENT VIDEO
From
Antenna
Stereo VCR
DTV Receiver with ColorStream™
From
DTV
Antenna
TV
Connecting a DTV receiver/set-top box
(with or without ColorStream™) and a VCR
This connection allows you to watch DTV (digital TV broadcast),
VCR, and TV programs, and record DTV and TV programs. You
can record from one source while watching a program from another
source.
Your TV has ColorStream component video inputs. Connecting your
TV to a ColorStream-compatible DTV receiver can greatly enhance
picture quality and realism.
You will need:
• one coaxial cable
• three pairs of audio cables (two single and one pair of audio
cables for a mono VCR)
• two video cables
• one set of ColorStream video cables (one S-video cable for a
non-ColorStream DTV receiver; see notes at right)
Note:
For the highest possible picture quality, you
must use ColorStream video cables between
the TV and DTV receiver. You can connect the
ColorStream cables from the DTV receiver to
either ColorStream jack on the TV (HD1 or
HD2).
The ColorStream HD1 and HD2 jacks can
be used with Progressive (480p) and
Interlace (480i, 1080i) scan systems. If you
receive the 1080i source, you may need to
change the picture size (see “Selecting 1080i
picture size” on page 34).
If your DTV receiver is not ColorStream-
compatible, use the S-video connections
(both audio and video) instead of the
ColorStream connections. (Be aware,
however, that a ColorStream connection
provides higher picture quality than an
S-video connection.) Do not connect both
S-Video and ColorStream cables between the
TV and DTV receiver at the same time.
To record from the DTV receiver, set the VCR
to Line IN. To monitor recording from the DTV
receiver, set the VCR to Line IN, and set the
TV to Video-1.
Caution:
The unauthorized recording of television
programs, videotapes, and other materials
may infringe upon the provisions of copyright
laws.
Introduction
Connecting
your TV
Using the
Remote Control
Setting up
your TV
Using the TV’s
Features
Appendix
Index
10
VIDEO
AUDIO
OUT
L
R
VIDEO-3 IN
VIDEOS-VIDEO
AUDIO
L/MONO R
Camcorder
Camcorder
VIDEO
AUDIO
OUT
L
R
M
55H70/61H70
Video-3 (front panel) of 43H70
Video-3 (front panel)
of 55H70/61H70
Connecting two VCRs
This connection allows you to record (dub/edit) from one VCR to
another VCR while watching a videotape. You can also record from
one TV channel while watching another TV channel.
You will need:
• one coaxial cable
• two pairs of audio cables (two single audio cables for mono
VCRs)
• two video cables (two S-video cables for S-VHS VCRs)
Caution:
The unauthorized recording of television
programs, videotapes, and other materials
may infringe upon the provisions of copyright
laws.
Note:
If you have S-VHS VCRs, use S-video cables
instead of regular video cables. Do not
connect both a regular video cable and an
S-video cable to Video-1 or Video-2 at the
same time.
Do not connect the same VCR to the output
and input jacks on the TV at the same time.
To dub or edit, VCR 2 must select Line IN,
and the TV must select Video-1.
*
The Video OUT jack does not output the
PIP picture.
**
The Audio OUT jacks can output the sound
of either the Main or PIP picture (see
“Selecting the Audio OUT sound” on
page 41).
Connecting a camcorder
This connection allows you to watch video materials recorded
on a camcorder.
You will need:
• one pair of audio cables
• one video cable (one S-video cable for an S-VHS
camcorder)
Caution:
If you have an S-VHS camcorder, use an
S-video cable between the S-video jacks on
the camcorder and TV. Do not connect both
a regular video cable and an S-video cable at
the same time.
OUT
RL
VAR
AUDIO
OUT
VIDEO
L/
MONO
IN
L
R
PB
PR
Y
L/
MONO
AUDIO
S-VIDEO
VIDEO
R
VIDEO-1 VIDEO-2
COLOR
STREAM
AUDIO
AUDIO
ININ
L
R
R
AUDIO
COLOR
STREAM
HD 2HD 1
PB
PR
Y
VIDEO AUDIO
CH 3
LR
CH 4
IN
OUT
VIDEO AUDIO
CH 3
LR
CH 4
IN from ANT OUT to TV
IN
OUT
ANT
(
75
)
ANT-1
CHANNEL IN
ON OFF
OUT
ANT-2
AUDIO CENTER
From
Antenna
VCR2
TV
VCR1
**
*
Introduction
Connecting
your TV
Using the
Remote Control
Setting up
your TV
Using the TV’s
Features
Appendix
Index
11
Caution:
To avoid damaging the speakers, turn the TV
off before connecting or disconnecting the
Audio Center Channel audio cable.
Connecting an audio system
This connection allows you to use an audio amplifier to adjust
the audio level. This also allows you to use external speakers.
To control the audio, turn on the TV and the stereo amplifier,
and turn off the built-in speakers (see“ Turning off the built-in
speakers” on page 41.)
You will need:
• one pair of audio cables
Note:
To hear sound when using an external audio amplifier, the
volume of both the TV and the amplifier must be set
above 0 (zero). If the volume of one is set to 0, you will
not be able to hear any sound, even the volume of the
other is at its highest setting.
OUT
RL
VAR
AUDIO
OUT
VIDEO
L/
MONO
IN
L
R
PB
PR
Y
L/
MONO
AUDIO
S-VIDEO
VIDEO
R
VIDEO-1 VIDEO-2
COLOR
STREAM
AUDIO
AUDIO
ININ
L
R
R
AUDIO
COLOR
STREAM
HD 2HD 1
PB
PR
Y
ANT
(
75
)
ANT-1
CHANNEL IN
ON OFF
OUT
ANT-2
AUDIO CENTER
LINE IN
LR
Amplifier
TV
From Cable, Cable Box, or Antenna
Note:
Refer to the instructions provided with your A/V receiver
for details about your surround sound system.
When the Audio Center Channel ON/OFF switch is in
the ON position, the TV speakers will function only as
center channel speakers.
Adjust the volume for the center channel speakers using
the center level control on the A/V receiver.
To use the TV speakers as normal speakers, set the
Audio Center Channel ON/OFF switch to the OFF
position.
Connecting an A/V receiver
This connection allows you to use an audio/video (A/V)
receiver to enhance your TV’s sound.
If you have a system with Dolby Pro Logic
®
surround sound, you can
use the TV’s internal speakers as center channel speakers, which will
add to the realism of the sound.
You will need:
• one pair of audio cables
• one single audio cable for the audio center channel
• one video cable
OUT
RL
VAR
AUDIO
OUT
VIDEO
L/
MONO
IN
L
R
P
B
P
R
Y
L/
MONO
AUDIO
S-VIDEO
VIDEO
R
VIDEO-1 VIDEO-2
COLOR
STREAM
AUDIO
AUDIO
ININ
L
R
R
AUDIO
COLOR
STREAM
HD 2HD 1
P
B
P
R
Y
ANT
(
75
)
ANT-1
CHANNEL IN
ON OFF
OUT
ANT-2
AUDIO CENTER
ON OFF
To A/V Receiver
Video
OUT
Video
IN
Center
OUT
From
Antenna
TV
_________
Dolby Pro Logic is a registered trademark of Dolby
Laboratories Licensing Corporation.
T V
Right
speaker
Left
speaker
Surround
speaker L
Surround
speaker R
VCR
A/V receiver
Audio Video
Video
Audio
Video
Audio
center
channel
Audio
LDP/DVD
Dolby Pro Logic
®
surround sound
system connection example
Introduction
Connecting
your TV
Using the
Remote Control
Setting up
your TV
Using the TV’s
Features
Appendix
Index
12
Using the remote control
Preparing the remote control for use
The remote control will operate your TV, most VCR models, and
most cable TV converters together, even if they are different brands. If
you will be using your TV with a Toshiba VCR, your remote control
is already programmed and ready to use. If you own different brands
of VCRs and/or converters, you must first program your remote
control (see “Programming the remote control for use with a VCR or
a cable TV converter” on page 12).
Installing the remote control batteries
To install the batteries:
1. Slide the battery cover off of the back of the remote control.
2. Install two “AA” size alkaline batteries. Match the + and – signs
on the batteries to the signs on the battery compartment.
3. Slide the battery cover back on to the remote control until the
lock snaps.
Using the remote control with a VCR or
cable TV converter
To control a Toshiba VCR:
1. Set the TV/CABLE/VCR switch to the VCR position. The
shaded buttons in the illustration at right will then control the
VCR. The unshaded buttons will operate the TV as usual.
To control a cable TV converter:
1. Program the remote control to recognize the brand of your
converter (see “Programming the remote control for use with a
VCR or cable TV converter” on page 13). The shaded buttons in
the illustration at right will control the cable TV converter.
2. Set the TV/CABLE/VCR switch to the CABLE position.
Note:
This remote control’s functions may or may
not operate your VCR or cable TV converter.
Refer to the owner’s manuals supplied with
the equipment to see which features are
available. In addition, the original controllers
may have features not available on this remote
control. If you would like to continue to use
these features, you may want to use the
original remote control.
Caution:
• Dispose of your batteries in a designated
disposal area. Do not throw your batteries
into a fire.
• Do not mix battery types or combine used
batteries with new ones.
• Remove dead batteries immediately to
prevent battery acid from leaking into the
battery compartment.
• If you do not intend to use the remote
control for a long time, remove the
batteries.
123
456
789
ENT
100
0
CH
VOL
POWER
TIMER
RECALL
TV/VIDEO
MUTE
TV
CABLE
VCR
CH RTN
STROBE
EXIT
LIGHT
STOP SOURCE
ADV/
PIP CH
ADV/
PIP CH
FAV
FAV
PLAY PIP
REC TV/VCR REW FF
STILL LOCATE SWAP
FAVORITE
MENU/
PREVIEW
ENTER
POWER
Channel
Number
ENTER
TV/CABLE/VCR
PLAY
STOP
Fast Forward
Rewind
TV/VCR
Record
Channel yz
Introduction
Connecting
your TV
Using the
Remote Control
Setting up
your TV
Using the TV’s
Features
Appendix
Index
13
Brand Code
Adventura 019
Aiko 297
Aiwa 019
Akai 060,068,080,125,
261
American High 054
Asha 259
Audiovox 056
Beaumark 259
Bell & Howell 123
Brandt 206
Broksonic 140,203,230,314,
380
Calix 056
Canon 054
Capehart 039
Carver 100
CCE 091,297
Citizen 056,297
Colt 091
Brand Code
Craig 056,066,091,259
Curtis Mathes 054,060,079
Cybernex 259
Daewoo 039,064,297
Daytron 039
Dynatech 019
Electrohome 056
Electrophonic 056
Emerex 051
Emerson 019,021,056,062,
080,087,140,203,
227,228,230,231,
297,313,314,380,
498
Fisher 066,073,085,123
Fuji 052,054
Funai 019,344
Garrard 019,344
GE 054,079,084,221
Go Video 251,298
Brand Code
Goldstar 037,056,057
Gradiente 019
Harley Davidson 019
Harman/Kardon 057,094
Harwood 087,091
Headquarter 065
HI-Q 066
Hitachi 060,061,084,124,
254
Jensen 060
JVC 027,060,086
Kenwood 057,060,086
KLH 091
Kodak 054,056
Lloyd 019
Lloyd’s 227
Logik 091
LXI 056
Magnavox 054,058,100,129,
168
Programming the remote control for use
with a VCR or cable TV converter
The remote control provided with your Toshiba TV is pre-
programmed to operate Toshiba VCRs. To use your TV remote
control to operate non-Toshiba VCRs and cable converters:
1. Refer to the VCR and cable TV converter code table (below and
on the next page) to find the corresponding code for your VCR
or converter brand.
If more than one code is listed, try each one separately until you
find the one that works.
2. If you are programming the remote control to operate your:
• VCR: Set the TV/CABLE/VCR switch on the remote
control to VCR.
• Cable converter: Set the TV/CABLE/VCR switch on the
remote control to CABLE.
3. While holding down the RECALL button, press the Channel
Number buttons to enter the three-digit code for your brand of
VCR or converter.
4. Point the remote control at the VCR or converter and press
POWER to test the code.
If the VCR or converter turns on, you have entered the right
number.
If the VCR or converter does not respond to the remote control,
repeat steps 1–4 using a different code.
5. Reset the TV/CABLE/VCR switch to TV to control the TV.
For future reference, write down the code(s) you used:
VCR code _____________________
Cable code _____________________
VCR codes
Note:
• Each time you replace the batteries, you
must reprogram the remote control.
• Some newer VCRs are capable of working
on either of two remote codes. These VCRs
have a switch labeled “VCR1/VCR2.” If
your VCR has this kind of switch and does
not respond to the programmed code, set
the switch to the other position (VCR1 or
VCR2) and reprogram the remote control.
123
456
789
ENT
100
0
CH
VOL
POWER
TIMER
RECALL
TV/VIDEO
MUTE
TV
CABLE
VCR
CH RTN
STROBE
EXIT
LIGHT
ADV/
PIP CH
ADV/
PIP CH
FAV
FAV
FAVORITE
MENU/
PREVIEW
ENTER
POWER
Channel
Number
Channel yz
Enter
Introduction
Connecting
your TV
Using the
Remote Control
Setting up
your TV
Using the TV’s
Features
Appendix
Index
14
Brand Code
Magnin 259
Marantz 054,100
Marta 056
Masushita 054
MEI 054
Memorex 019,054,056,058,
065,066,067,123,
259
MGA 062,080
MGN Technology 259
Minolta 061,124
Mitsubishi 062,080,086,094,
192,233,261
Motorola 054,067
MTC 019,259
Multitech 019,091
Nad 077
NEC 057,059,060,069,
086
Nikko 056
Noblex 259
Olympus 054
Optimus 056,067,077,123
Optonica 081
Orion 498
Panasonic 054,096,181,244
Penney 054,056,057,059,
061,073,259
Pentax 061,084,124
Philco 054
Philips 054,081,100,129
Pilot 056
Pioneer 077,086
Portland 039
Protec 091
Pulsar 058
Quarter 065
Quartz 065
Quasar 054,096
Radio Shack 019,056,344
Radix 056
Randex 056
RCA 061,079,084,096,
124,125,168,221
Realistic 019,054,056,065,
066,067,081,085,
123,259
Ricoh 053
Runco 058
Samsung 064,259
Sanky 058,067
Sansui 060,086
Sanyo 065,066,123,259
Scott 062,064,140,203,
229,230,231
Brand Code
Sears 054,056,061,065,
066,073,085,123,
124
Sharp 067,081
Shintom 091
Shogun 259
Singer 091
Sony 051,052,053,054
STS 061
Sylvania 019,054,062,100,
129
Symphonic 019,344
Tatung 060
Teac 019,060
Technics 054,181
Teknika 019,054,056,071
Telefunken 060,206
TMK 227,259
Toshiba 062,064,085,229,
231,385
Totevision 056,259
Unitech 259
Vector 064
Vector Research 057,059
Video Concepts 059,064,080
Videosonic 259
Wards 019,054,061,066,
067,081,091,168,
231,259
XR-1000 019,054,091
Yamaha 057
Zenith 052,053,058
Cable TV converter codes
Brand Code
ABC 020,022,026,027,
030,032,033,036,
066
Antronix 041
Archer 041,058,172
Belcor 075
Cable Star 075
Cabletenna 041
Cableview 041
Century 172
Citizen 172
Colour Voice 044,050
Comtronics 059,079
Contec 038
Dae Ryung 027
Eastern 021
Focus 419
Garrard 172
GC Electronics 035,075
Gemini 034,089
Brand Code
General Instrument 030,295
GoldStar 059,163
Hamlin 028,039,053,278,
292
Hitachi 030
Hytex 026
Jasco 172
Jerrold 022,030,031,033,
034,043,066,295
Macom 052
Magnavox 046
Memorex 019
Movie Time 175
NSC 089,175
Oak 026,038,267
Panasonic 019,040,126
Paragon 019
Philips 044,046,047,048,
049,050,172
Pioneer 042,163,552
Popular Mechanics 419
Pulsar 019
RCA 040
Recoton 419
Regal 039,278,292
Regency 021
Rembrandt 030,089
Runco 019
Samsung 059,163
Scientific Atlanta 025,027,036,296
Signal 034,059
Signature 030
SL Marx 059
Sprucer 040
Standard
Components 174
Starcom 022,034,066
Stargate 034,059
Starquest 034
Sylvania 020
Teleview 059
Texscan 020
Tocom 031,032,078
Toshiba 019
Tusa 034
Unika 041,172
United Artists 026
United Cable 022
Universal 041,058,075,096,
172,210
Viewstar 046,079,230
Zenith 019
Zentek 419
VCR codes (continued)
Introduction
Connecting
your TV
Using the
Remote Control
Setting up
your TV
Using the TV’s
Features
Appendix
Index
15
Learning about the remote control
LIGHT back-lights the remote control buttons for five seconds
RECALL displays on-screen information (page 42)
POWER turns the TV on and off (pages 13 and 37)
TV/CABLE/VCR Switch switches between TV, cable, and VCR
input sources (page 13)
MUTE mutes the sound (page 38)
TV/VIDEO selects the video input source (pages 17 and 37)
TIMER sets the TV to turn off at a specified time (page 37)
CH yz cycles through programmed channels (page 19)
Channel Numbers allow direct access to channels (page 19)
VOL yz adjusts the volume level
CH RTN returns to the last viewed channel (page 21)
ENT required by some VCRs and cable TV converters to
change channels
FAVORITE allows access to the Multi-Window function (page 25)
STROBE allows access to the Multi-Window function (page 26)
PREVIEW allows access to the Multi-Window function (page 25)
EXIT exits programming menus (page 16)
MENU allows access to programming menus (page 16)
ENTER sets programmed menu information (pages 16 and 21)
yzx • Buttons select or adjust programming menus (page 16)
ADV/PIP CH yz Buttons cycle through PIP channels (page 23)
FAV zy Buttons cycle through favorite channels (page 21)
PIP Buttons allow access to PIP functions (pages 23–25)
SOURCE selects the PIP input source
PIP turns the PIP on and off
STILL freezes the PIP
LOCATE changes the position of the PIP
SWAP switches between the main and PIP pictures
VCR Buttons allow access to VCR functions (page 5)
STOP stops a videotape from playing, recording,
rewinding, or fast-forwarding
PLAY plays a videotape
REC starts recording a videotape
TV/VCR toggles between the TV and VCR
when viewing while recording
REW rewinds a videotape
FF fast-forwards a videotape
123
456
789
ENT
100
0
CH
VOL
POWER
TIMER
RECALL
TV/VIDEO
MUTE
TV
CABLE
VCR
CH RTN
STROBE
EXIT
LIGHT
STOP SOURCE
ADV/
PIP CH
ADV/
PIP CH
FAV
FAV
PLAY PIP
REC TV/VCR REW FF
STILL LOCATE SWAP
FAVORITE
MENU/
PREVIEW
ENTER
Introduction
Connecting
your TV
Using the
Remote Control
Setting up
your TV
Using the TV’s
Features
Appendix
Index
16
Setting up your TV
Learning about the menu system
After you have installed the batteries and programmed the remote
control, you will need to set some preferences on the TV using the
menu system. You can access the menu using the buttons on your TV
or remote control.
1. Press MENU to display the menu system.
2. Press x or • to select a menu.
3. Press y or z to select an item.
4. Press x or • to select or adjust a setting.
SELECT:
P CTURE ANTENNAI
MODE SPORTS
PREFERENCE
CONTRAST
BR GHTNESSI
COLOR
RESET
SAVE NEW
TINT
SHARPNESS
50
50
50
0
100
END:EXIT
MOVE: SELECT:
P CTURE ANTENNAI
MODE SPORTS
PREFERENCE
FLESH TONE ON
OFF
COOL
OFF/
DNR
CONVERGENCE
SAVE NEW
COLOR
TEMPERATURE
SELECT:
AUD OI
MTS
BASS
STEREO
50
50
0
TREBLE
BALANCE
RESET
END:EXIT
MOVE: SELECT:
AUD OI
SBS
SBS LEVEL
ON
ON
ON
MA NI
50
OFF/
SPEAKERS
AUD O OUTI
STABLE SOUND
SELECT:
THEATER
SURROUND
P I CTURE S I ZE
1080I
SRS
OFF
END
:
EXIT
SELECT:
SET UP
LANGUAGE
CLOCK
ANT
ADD ADDERASE/
TV
CH
PROGRAM
CABLE/ CABLE
1 ANT1 ANT2//2
SET
ENGL SHI
END:EXIT
SELECT:
CUSTOM
T I MER
CC
FAVOR I CH
OFF
1TE
FAVOR I CH2TE
V
BACKGROUND
I
DEO
CH
LABEL
LABEL
ING
END:EXIT
:
SELECT
END:
LOCKS
VCHIP–
V
CH
NEW P I N
I LOCK
LOCK
CODE
DEO
ENABLE
TV RAT
MPAA
ING
RATI NG
BLOCK I NG
BLOCK I NG OPT I ON
OFF
OFF
EXIT
• Press ENTER to activate the function settings in the SET UP
menu.
• The main menu display will disappear automatically if you do not
make a selection within 15 seconds; the other displays will
disappear automatically within 6 seconds (except the
Convergence menu, which will remain until a button is pressed).
• If you want to close all the on-screen displays instantly, press
EXIT.
D
IO
R
DEMO
MENU
VOLUME
TV/VIDEO
CHANNEL
Notes:
• The menu illustrations on the following
pages have been distorted for easy
reference.
• You can change the background of the
menu. See page 42 for details.
• Model 43H70 does not have the EXIT
button on the TV.
MENU yzx • EXIT
MENU
VOL VOL
CH
CH
EXIT TV/VIDEO DEMO
POWER
MENU x •zy
43H70
55H70/61H70
123
456
789
ENT
100
0
CH
VOL
POWER
TIMER
RECALL
TV/VIDEO
MUTE
TV
CABLE
VCR
CH RTN
STROBE
EXIT
LIGHT
ADV/
PIP CH
ADV/
PIP CH
FAV
FAV
FAVORITE
MENU/
PREVIEW
ENTER
MENU/ENTER
EXIT
Introduction
Connecting
your TV
Using the
Remote Control
Setting up
your TV
Using the TV’s
Features
Appendix
Index
17
Changing the on-screen display language
You can choose from three different languages (English, French and
Spanish) for the on-screen displays. Adjustment menus and messages
will appear in the language of your choice.
To select a language:
1. Press MENU, then press x or • until the SET UP menu appears.
2. Press y or z to highlight LANGUAGE.
1
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19
20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35
12345678910111213141516171819
20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35
SET UP
LANGUAGE
CLOCK
ANT
ADD ADDERASE/
TV
CH
PROGRAM
CABLE/ CABLE
1 ANT1/2
SET
ENGL SH FRANCAI I ESPANOLS
//
3. Press x or • to highlight your desired language.
Selecting the antenna input
You can connect to two different signal sources by choosing the
antenna input (ANT 1 or ANT 2).
To select the antenna input:
1. Press MENU, then use x or • to highlight the SET UP menu.
2. Press y or z to highlight ANT 1/2.
1
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19
20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35
12345678910111213141516171819
20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35
SET UP
LANGUAGE
CLOCK
ANT
ADD ADDERASE/
TV
CH
PROGRAM
CABLE/ CABLE
1 ANT1 ANT2//2
SET
ENGL SHI
3. Press x or • to highlight either ANT 1 or ANT 2, depending on
the antenna terminal you wish to use.
Using the TV/VIDEO button on the TV
To use the TV/VIDEO button on the TV to monitor or change your
TV’s signal source:
1. Press the TV/VIDEO button on the TV to monitor the source.
The current signal source is displayed in purple.
2. Continue pressing the TV/VIDEO button to change to either
ANT 2, ANT 1, VIDEO 1, VIDEO 2, VIDEO 3, ColorStream
HD1, or ColorStream HD2.
1
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19
20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35
12345678910111213141516171819
20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35
SOURCE
ANT 2
ANT
V IDEO
1
1
V IDEO 2
V
CSooltreamr
I DEO
HD1
CSooltreamr
HD2
3
SELECT ION
D
IO
R
DEMO
MENU
VOLUME
TV/VIDEO
CHANNEL
D
IO
R
DEMO
MENU
VOLUME
TV/VIDEO
CHANNEL
MENU x •zy
TV/VIDEO
MENU
VOL VOL
CH
CH
EXIT TV/VIDEO DEMO POWER
MENU yzx •
MENU
VOL VOL
CH
CH
EXIT TV/VIDEO DEMO POWER
TV/VIDEO
43H70
43H70
55H70/61H70
55H70/61H70
123
456
789
ENT
100
0
CH
VOL
POWER
TIMER
RECALL
TV/VIDEO
MUTE
TV
CABLE
VCR
CH RTN
STROBE
EXIT
LIGHT
ADV/
PIP CH
ADV/
PIP CH
FAV
FAV
FAVORITE
MENU/
PREVIEW
ENTER
MENU/ENTER
EXIT
Introduction
Connecting
your TV
Using the
Remote Control
Setting up
your TV
Using the TV’s
Features
Appendix
Index
18
Adding channels to the TV’s memory
Your TV will stop on specific channels that are stored in the TV’s
channel memory when you press Channel y or z. Use the steps
below to set all active channels in your area automatically.
Programming channels automatically
Your TV can automatically detect all active channels and store them
in its memory. After the TV has stored the channels in its memory,
you can erase channels or add your favorite channels. If you use both
ANT-1 and ANT-2 terminals, you must program channels for each
input source.
To add channels:
1. Press MENU, then press x or • until the SET UP menu
appears.
2. Press y or z until TV/CABLE is highlighted.
3. Press x or • to highlight either TV or CABLE, depending on
which you use.
1
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19
20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35
12345678910111213141516171819
20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35
SET UP
LANGUAGE
CLOCK
ANT
ADD ADDERASE/
TV
CH
PROGRAM
TV/ CABLE/ CABLE
1 ANT1/2
SET
ENGL SHI
If you use an antenna, choose TV.
If you use cable, choose CABLE.
4. Press z to select CH PROGRAM.
1
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19
20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35
12345678910111213141516171819
20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35
SET UP
LANGUAGE
CLOCK
ANT
ADD ADDERASE/
TV
CH
PROGRAM
CABLE/ CABLE
1 ANT1/2
SET
ENGL SHI
5. Press x or • to start channel programming. The TV will
automatically cycle through all the TV or Cable channels
(depending on which you selected), and store all active channels
in the channel memory.
While the TV is cycling through the channels, the message
“Programming Now—Please Wait” appears.
6. When channel programming is complete, the message
“Completed” appears.
7. Press Channel y or z to view the programmed channels.
123
456
789
ENT
100
0
CH
VOL
POWER
TIMER
RECALL
TV/VIDEO
MUTE
TV
CABLE
VCR
CH RTN
STROBE
EXIT
LIGHT
ADV/
PIP CH
ADV/
PIP CH
FAV
FAV
FAVORITE
MENU/
PREVIEW
ENTER
MENU
Channel yz
EXIT
Introduction
Connecting
your TV
Using the
Remote Control
Setting up
your TV
Using the TV’s
Features
Appendix
Index
19
D
IO
R
DEMO
MENU
VOLUME
TV/VIDEO
CHANNEL
MENU
VOL VOL
CH
CH
EXIT TV/VIDEO DEMO POWER
Adding and erasing channels manually
After you’ve programmed the channels, you can add or erase specific
channels.
To add or erase channels:
1. Select the channel you want to add or erase using Channel y or
z. If adding channels, you must select the channel to add by
using the Channel Number buttons.
2. Press MENU, then press x or • until the SET UP menu
appears.
3. Press y or z to highlight ADD/ERASE.
1
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19
20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35
12345678910111213141516171819
20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35
SET UP
LANGUAGE
CLOCK
ANT
ADD ADD ERASE/ERASE/
TV
CH
PROGRAM
CABLE/ CABLE
1 ANT1/2
SET
ENGL SHI
4. Press x or • to select ADD or ERASE, whichever function you
want to perform.
5. Repeat steps 1-4 for other channels you want to add or erase.
Changing channels
To change the channel, you can:
• change the programmed channels using the remote control
• select a channel directly using the remote control
• scan the channels using the TV buttons
To change to the next programmed channel:
Press Channel y or z on the TV or remote control.
To change to a specific channel (programmed or unprogrammed):
Press the Channel Number buttons (0-9 and 100).
For example, to select channel 125, press the 100 button, the 2
button, and the 5 button.
Adjusting the color convergence
This projection TV uses three separate TV tubes: a red one, a green
one, and a blue one. The red, green, and blue images are projected
onto the screen where they converge to form a full color picture. You
can see a clear picture only when they converge correctly.
Convergence may drift over time or if you move the TV. If you can
see clear images on the screen, skip this procedure.
This adjustment should be made after the TV has been on for at least
30 minutes.
MENU x •zy
Channel yz
MENU
x •zy
Channel zy
43H70
55H70/61H70
123
456
789
ENT
100
0
CH
VOL
POWER
TIMER
RECALL
TV/VIDEO
MUTE
TV
CABLE
VCR
CH RTN
STROBE
EXIT
LIGHT
ADV/
PIP CH
ADV/
PIP CH
FAV
FAV
FAVORITE
MENU/
PREVIEW
ENTER
MENU
Channel yz
Channel
Number
EXIT
Introduction
Connecting
your TV
Using the
Remote Control
Setting up
your TV
Using the TV’s
Features
Appendix
Index
20
To check and adjust the color convergence:
1. Press MENU, then press x or • until the PICTURE menu
appears.
2. Press y or z to highlight CONVERGENCE.
1
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19
20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35
12345678910111213141516171819
20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35
P CTURE ANTENNAI
MODE SPORTS
PREFERENCE
FLESH TONE ON
OFF
COOL
DNR
CONVERGENCE
SAVE NEW
COLOR
TEMPERATURE
3. Press x or • to display the center CONVERGENCE menu.
1
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19
20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35
12345678910111213141516171819
20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35
EXI T TO SELECT POSI IONT:
ENTER
RED BLUE
TO SELECT COLOR:
If you see separate colored lines, you have to adjust the
convergence.
4. Press ENTER to highlight RED or BLUE.
5. Press y (up), z (down), x (left), or • (right) on the remote
control to converge the red or blue line into the green line. When
color convergence is correctly adjusted, you will see two single
crossed white lines.
6. Press EXIT to display the circumference CONVERGENCE
menu.
7. Press the corresponding Number button (1–9) to select the area
you want to adjust.
1
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19
20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35
12345678910111213141516171819
20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35
PUSH 1
8
2
9
3
6
7
1
4
9–
8. Press ENTER to highlight RED or BLUE.
1
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19
20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35
12345678910111213141516171819
20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35
RED BLUE
EXI T TO SELECT POSI IONT:
ENTER TO SELECT COLOR:
9. Press yzx • to converge the red or blue line into the green line.
Repeat steps 8 and 9 until you see two single crossed white lines.
10. Press EXIT once to select another area to adjust, then repeat
steps 7–9.
11. Press EXIT twice to close the CONVERGENCE menu.
123
456
789
ENT
100
0
CH
VOL
POWER
TIMER
RECALL
TV/VIDEO
MUTE
TV
CABLE
VCR
CH RTN
STROBE
EXIT
LIGHT
ADV/
PIP CH
ADV/
PIP CH
FAV
FAV
FAVORITE
MENU/
PREVIEW
ENTER
MENU
Channel yz
Channel
Number
EXIT
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
/
