V-ZUG 789 Installation guide

V-ZUG
Brand
V-ZUG
Model
789
Category
Cooker hoods
Type
Installation guide

This manual is also suitable for

V-ZUG 789 offers versatile options for ventilation in your kitchen. Whether you choose extraction or recirculation mode, this range hood ensures efficient removal of cooking fumes and odors. With its sleek island hood design, it fits perfectly above your cooktop, providing optimal performance and a stylish accent to your kitchen.

V-ZUG 789 offers versatile options for ventilation in your kitchen. Whether you choose extraction or recirculation mode, this range hood ensures efficient removal of cooking fumes and odors. With its sleek island hood design, it fits perfectly above your cooktop, providing optimal performance and a stylish accent to your kitchen.

Installation instructions
Range hood DI-M10, DI-M12
Island hood
Operating modes: extracted air / recirculation air
J789.113-3
20.5.09 FUW
1
These installation instructions apply to the models:
789 (DI-M10, construction width 100 cm)
790 (DI-M12, construction width 120 cm)
Identification plate
A Remove grease filter. The identification plate is on the inside of the appliance.
Supplied installation accessories
All fixing elements are contained in the scope of delivery.
Extraction mode
If the total hood height is >800 mm:
Extension for hexagonal socket key: Art. no. H4.1891
A Information on the necessary mains voltage, type of current and fuse protection can be taken from the identification plate.
Option connection
The appliance should be installed by qualified personnel only. Each step must be carried out and checked in full in the order
specified.
Validity
General notes
With the simultaneous operation of firing (e.g. wood, gas, oil or coal-fired heating systems), safe operation is only possible
providing a room negative pressure of 4 Pa (0.04 mbar) is not exceeded at the location of the appliance. Risk of toxic fumes!
An adequate flow of fresh air must be guaranteed, e.g. via non-closable openings in doors and windows and combined with
ventilation wall bricks for incoming and exhaust air or by other technical means.
If the appliance is installed over hobs, each cooking zone must be fitted with an ignition fuse and the minimum distances (see
«Dimensions») must be adhered to.
Efficient repairs can only be guaranteed if it is possible to disconnect the appliance at any time without causing any damage.
The extracted air must not be fed into a chimney which is used for exhausting fumes from appliances burning gas or other fuels.
Always observe the fire regulations.
Special tool
Electrical connections
Electrical connections must be carried out by trained electricians in accordance with the guidelines and standards for low
voltage installations and the specifications of the local electricity supply companies.
A plug-in appliance may only be connected to a socket outlet with earthing contact, installed according to specifications. An
all-pole mains isolating device with 3 mm contact opening should be provided in the house wiring system. Switches, plug and
socket devices, circuit breakers and fusible cut-outs which are accessible after installation and which have all-poles switching
are permissible as isolating devices. Effective earthing and separately installed neutral and earth conductors ensure safe and
fault-free operation. After installation, live parts and cables with basic insulation must not be accessible. Old installations should
always be checked.
The option may not be connected by a second side with mains voltage.
Installation instructions
Range hood DI-M10, DI-M12
Island hood
Operating modes: extracted air / recirculation air
J789.113-3
20.5.09 FUW
2
Dimensions
Drill plan (view from above)
Telescopic casing
(available in various heights)
Height A:
A see planning documents for kitchen appliances
Distance above hob
Minimum height B:
For electric hob:
For gas hob:
min. 600 mm
min. 750 mm
~405 68
BA
ø 150
1000/1200
700
376
257
207
231
263
305
299
249
273
ø 13
299
257
Installation instructions
Range hood DI-M10, DI-M12
Island hood
Operating modes: extracted air / recirculation air
J789.113-3
20.5.09 FUW
3
Indications
䡲 Avoid routing the exhaust air pipeline to the side through the flue casing.
䡲 Planning features for non-destructive de-installation and maintenance of the appliance:
– Do not route telescopic casing in suspended ceilings.
– Avoid silicon joints between the telescopic casing and the appliance.
– All plastering, plasterboarding, wall papering or painting work is to be carried out prior to the appliance installation.
Installation – extraction mode
1. Measure the centre point of the hob.
2. Attach paper template C to the ceiling, drill 4 holes L1 (ø 10 mm) and push
plugs.
3. Screw hanger bolts S into the holes L1 and leave 20 mm protruding.
4. Fix the exhaust air hose to the exhaust air pipe (min. ø 150 mm) in the ceiling
and cut it down to be 10 cm longer than upper lagging sheet V1.
5. Determine the installation height and drill 4 holes L2 into upper lagging sheet
V1 with help of the dimension data on sheet H.
Observe the minimum distance B above the hob:
6. Attach upper lagging sheet V1 to the ceiling with washers, nuts M.
7. Slide lower lagging sheet V2 over upper lagging sheet V1 and attach with
adhesive strips J.
8. Fix exhaust air hose to exhaust air connector. Ensure hose is free from kinks
and is stretched.
9. Execute the electrical connection (see section «Electrical connections»).
10. Bolt together hood K and upper lagging sheet V1.
11. Remove adhesive strips J and position lower lagging sheet V2 correctly on the
hood.
Installation
The 4 holes L2 must be aligned horizontally.
For electric hob: min. 600 mm
For gas hob: min. 750 mm
C
S
H
L2
J
V2
L1
M
V1
K
Installation instructions
Range hood DI-M10, DI-M12
Island hood
Operating modes: extracted air / recirculation air
J789.113-3
20.5.09 FUW
4
Installation – recirculation mode
1. Measure the centre point of the hob.
2. Affix drilling template C to the ceiling. Drill 4 holes L1 (ø 10 mm) and push
plugs.
3. Screw hanger bolts S into the holes L1 and leave 20 mm protruding.
4. Use drill template D to drill 4 holes for attachment E for diverter piece F.
5. Bend up mounting links G by about 1 mm. Screw on attachment E and click
diverter piece F into place from underneath.
6. Fix the exhaust air hose to the exhaust air pipe (min. ø 150 mm) in the ceiling
and cut it down to be 10 cm longer than upper lagging sheet V1.
7. Determine the installation height and drill 4 holes L2 into upper lagging sheet
V1 with help of the dimension data on sheet H.
Observe the minimum distance B above the hob:
8. Attach upper lagging sheet V1 to the ceiling with washers, nuts M.
9. Slide lower lagging sheet V2 over upper lagging sheet V1 and attach with
adhesive strips J.
10. Fix exhaust air hose to exhaust air connector. Ensure hose is free from kinks
and is stretched.
11. Execute the electrical connection (see section «Electrical connections»).
12. Bolt together hood K and upper lagging sheet V1.
13. Remove adhesive strips J and position lower lagging sheet V2 correctly on the
hood.
14. Place activated carbon filters N into brackets O and attach to upper lagging
sheet V1.
The 4 holes L2 must be aligned horizontally.
For electric hob: min. 600 mm
For gas hob: min. 750 mm
F
E
D
G
J
V2
M
V1
N
O
C
S
L1
H
L2
K
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4

V-ZUG 789 Installation guide

V-ZUG
Brand
V-ZUG
Model
789
Category
Cooker hoods
Type
Installation guide
This manual is also suitable for

V-ZUG 789 offers versatile options for ventilation in your kitchen. Whether you choose extraction or recirculation mode, this range hood ensures efficient removal of cooking fumes and odors. With its sleek island hood design, it fits perfectly above your cooktop, providing optimal performance and a stylish accent to your kitchen.

Download PDF
report

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI

Related papers

Other documents