ElectrIQ CD12LE User manual

Brand: ElectrIQ

Model: CD12LE

Category: Dehumidifiers

Type: User manual

This manual is also suitable for

CD20LE

ElectrIQ CD12LE is a premium low energy dehumidifier with a digital humidistat and air purifier, ideal for 3-bedroom houses. Featuring low power consumption and a power-saving logic, it's a cost-effective way to combat mold, condensation, and damp. It dries laundry more efficiently than a tumble dryer and complements any modern space. Its intelligent CPU-controlled digital humidistat maintains your desired humidity level between 35-80% RH.

USER MANUAL

PREMIUM LOW ENERGY COMPRESSOR

DEHUMIDIFIER WITH DIGITAL HUMIDISTAT

AND AIR PURIFIER

CD12LE – 12 litres per day

CD20LE – 20 litres per day

Thank you for choosing electriQ.

Please read this user manual before using this innovative

Dehumidier and keep it safe for future reference

Visit our page www.electriQ.co.uk for our entire range of Intelligent Electricals

CONTENTS

SAFETY INSTRUCTIONS 2

INSTALLATION 5

PARTS 6

CONTROL PANEL 7

QUICK REFERENCE GUIDE 8

POSITIONING 11

WATER DRAINAGE 12

CARE AND MAINTENANCE 12

TROUBLESHOOTING 14

TECHNICAL DATA 15

Carefully read the instructions before operating the unit

This appliance is for indoor use only and intended for use in a domestic

environment only. Any other use is not recommended by the manufacturer and

may cause re, electrical shocks or other injury to user or property.

Rating: This unit must be only connected to a 220-240 V / 50 Hz earthed outlet.

Installation must be in accordance with regulations of the country where the unit is

used.

If you are in any doubt about the suitability of your electrical supply have it

checked and if necessary, modied by a qualied electrician.

This dehumidifier has been tested and is safe to use. However, as with any

electrical appliance - use it with care.

Disconnect the power before dismantling, assembling or cleaning.

Avoid touching any moving parts of the appliance.

Never insert ngers, pencils or any other objects though the guard

This appliance is not intended for use by persons (including children) with reduced

physical, sensory or mental capabilities. It is also not intended for use by those

with a lack of experience and knowledge, unless they have been given supervision

or instruction concerning the use of the appliance by a person responsible for their

safety.

Do not leave children unsupervised with this appliance.

Do not clean the unit by spraying it or immersing it in water.

Never connect the unit to an electrical outlet using an extension cord. If a power

outlet is not available, one should be installed by a qualied electrician.

Never operate this appliance if the cord, power adapter or plug is damaged.

Ensure the power cord is not stretched or exposed to sharp objects/edges.

A damaged power supply cord should be replaced by the manufacturer or a

qualied electrician in order to avoid a hazard.

Any service other than regular cleaning or lter replacement should be performed

by an authorized service representative. Failure to comply could result in a voided

warranty.

Do not use the appliance for any purpose other than its intended use.

Do not tilt the unit while in use. The unit is design to work only in vertical position.

This dehumidifier must always be stored and transported upright, otherwise

irreparable damage may be caused to the compressor; if in doubt we suggest

waiting at least 24 hours before starting the unit.

Avoid restarting the dehumidier unless 5 minutes have passed since being turned

off. This prevents damage to the compressor.

Never use the plug as a switch to start or turn off the dehumidifier. Use the

provided ON/OFF switch located on the control panel.

Always place the unit on a dry and stable surface.

The appliance should not be installed in laundry or wet rooms where the humidity

is higher than 85% RH

Do not dry laundry above the unit to prevent water entering the dehumidier. Place

the laundry at least 1 meter away from your dehumidier.

IMPORTANT

SAFETY INSTRUCTIONS

The appliance must be placed in a room without sources of ignition (for example:

open ames, an operating gas appliance or an operating electric heater).

R290 refrigerant gas complies with European environmental directives.

R290 has a low GWP (Global Warming Potential) of 3.

The CD12LE contains about 60g of R290 refrigerant gas.

The CD20LE contains about 75g of R290 refrigerant gas.

Do not use or store the CD20LE in an unventilated space with an area smaller

than 4.1m2 per unit.

Do not use or store the CD12LE in an unventilated space with an area smaller

than 2.6m2 per unit.

If the appliance is installed, used or stored in an unventilated room, the room must

be such as to prevent stagnation of possible leaks of refrigerant gas as there

could be a danger of re or explosion should the refrigerant come into contact with

electric heaters, stoves or other sources of ignition.

Refrigerant gas may be odourless.

Do not use the product and contact the retailer for advice, if damage has occurred

to the unit which may have compromised the refrigerant system.

Any repairs or maintenance must only be carried out on the unit by a suitably

qualied engineer. Before opening and servicing the unit the authorized engineer

must be in possession of a copy of the manufacturer’s service manual and

must follow the safety information contained within it to ensure all hazards are

minimized.

The refrigerant system should not be perforated or punctured.

Do not place the unit next to heat sources (e.g. electrical res, replaces, etc.)

Avoid mishandling the dehumidifier. Dropping, throwing the unit can cause

damage to its internals and increases the risks of operating it.

Do not store or use gasoline, petrol, paint, solvents or other ammable vapours or

liquids in the vicinity of this dehumidier or any other appliance.

This dehumidier must not be used in spaces where there is a high concentration

of gases, solvent or other volatile organic compounds; in very dusty environments;

in any domestic, commercial or industrial environment where the air composition

is ammable.

Do not cover or restrict the airow from the outlet or inlet grills. Do not operate and

follow troubleshoot procedure if the self-opening louvers do not open on power on.

For maximum performance the minimum distance from a wall or objects should be

20 cm

Keep the lters or grills of the unit clean. Under normal conditions, lters or grills

should only need cleaning once every three weeks (approximately).

Since the filters remove airborne particles, more frequent cleaning maybe

necessary, depending on the air quality. Vacuum both mesh and optional carbon

lters and wash the mesh lters with hot soapy water and dry them before placing

them back in the unit.

ENERGY SAVING AND UNIT SAFETY PROTECTION TIPS

0403

QUICK VISUAL SAFETY GUIDE ON WHERE OR WHEN NOT TO USE YOUR

DEHUMIDIFIER

Exposed to the

weather outdoors

Near water If the power cable

wires are frayed or cut

Where small children

may be left

unattended

If an extension lead

may become

overloaded

Where the power cable

may be damaged

On a slope or uneven

surface

Where there is risk

of re or close to a

naked ame

Where it may be

damaged by

chemicals

Where there is a risk

or interference by

foreign objects

This product is not

made for DIY repair

If there is a risk

of water faling on

the unit

0403

INSTALLATION

Remove any water from within the water tank before starting the unit. In order to

save energy do not open windows or doors while the unit is running. Place the unit

on a hard / at surface. On rst use run the unit continuously for 24 hrs.

TO REDUCE NOISE LEVELS:

Place a piece of carpet or a rubber mat under the unit to reduce any vibrations while

the unit is running.

The CD12LE and CD20LE dehumidifiers use compressor technology to extract

water from the environment. Compressor dehumidifiers are ideal for normal

domestic or office environments which are heated during the winter months and

maintain a temperature above 12-15

The dehumidiers are easy to move around on castors and are designed to extract

unwanted humidity while saving money due to their power saving logic. They

feature an intelligent humidistat where the desired relative humidity can be adjusted

in increments of 5% between 40 and 80% ensuring your room is not dried too much

and power is not wasted.

FEATURES

Your dehumidifier belongs to the electriQ low energy premium dehumidifiers

featuring low power consumption, power saving logic and advanced air purication

option.

Easy to use controls

Low energy only uses a fraction of the electricity of similar dehumidiers

Great for up to 3 bed (CD12LE) and 5 bed (CD20LE) houses

Cost effective way to combat mould, condensation and damp

Dries laundry more efciently than a tumble dryer

Designed to complement any modern space

Low and High fan speed selection for best balance between running quiet and

maximum water extraction

Anti-dust self-closing oscillating louvres for improved air ow

Castors for improved mobility

Intelligent CPU controlled digital humidistat with 35-80% RH and room humidity

display

24 hours start / stop timer

Tank operation or permanent drainage option with splash proof tank

Tank full alarm & auto-stop function

Air purier function with UV sterilisation

10.

11.

12.

13.

14.

0605

PARTS

8. Air inlet

11. Water tank

1. Louvers

3. Air outlet

4. Humidity

indicator light

6. Control Panel

2. Handle

5. Wheels

7. Pre-lter/activated

Carbon lter

9. Continuous

Drain Port

10. Back Cover

12. Power cord

OPTIONAL

Activated carbon lter (Optional)

0605

quality or remove odour.

HUMIDITY

INDICATOR

LIGHT

TIMER OSC

HIGH

LOW

SMART

AIR PURIFIER

OPERATION

TANK FULL

DEFROST

MODE

POWER

HUMIDITY

INDICATOR

LIGHT

TIMER OSC

HIGH

LOW

SMART

AIR PURIFIER

OPERATION

TANK FULL

DEFROST

MODE

POWER

CONTROL PANEL

On/Off

Water full indicator

Defrost indicator

Humidity Indicator Down Up Mode

Timer

Oscillation Power

POWER

Turn the appliance on/off

MODE Button

Select the function of the unit between: SMART / HIGH / LOW /

and FAN. The LED’s next to the button will show which mode is

selected.

SMART MODE: The unit will default to SMART mode the rst time

it is switched on and remains in this mode until another program

is chosen. In smart mode it will aim for a relative humidity of 50-

55%,and the fan speed will be adjusted automatically.

HIGH: The unit will dehumidify and aim for the humidity set using

the up and down buttons.

LOW: The unit will dehumidify and aim for the humidity set using

the up and down buttons.

Air Purifier : The unit will run in fan mode and will not extract

water. Use with the HEPA or Active Carbon filter to improve air

HUMIDITY

INDICATOR

LIGHT

HUMIDITY INDICATOR MODE

When the appliance is first started the indicator light will turn

on automatically. The colour of the indicator light will change

according to the humidity condition of the room it is situated in.

RED: High humidity, RH≥70%

ORANGE: Comfortable, 70%> RH ≥60%

GREEN: Dry, RH<60%

Press the “Humidity Indicator light” button to turn the light on/off.

NOTE: It can take around 2 minutes following a change in the

humidity for the indicator to change colour e.g. If the humidity

drops to 55% it may take 2 minutes before the indicator changes

to green.

0807

HUMIDITY LEVEL & TIMER 2 DIGIT DISPLAY

The led indicator performs the following functions:

1. When the unit is plugged in, it will indicate the humidity level of the room.

2. When the UP and DOWN buttons are pressed, it will indicate the desired humidity

currently set.

3. When the timer is programmed will show the duration.

Notes: When humidity level is outside the normal operational parameters will show LO/HI. If

ambient humidity is lower than 20%, it will show “LO” If ambient humidity is higher than 90%, it

will show “HI”

OSC

OSC. (Oscillation function)

There are three different options for the outer louvre on the unit. It can be set

at 45 or 90 degrees, or alternatively to swing. Use the dehumidier at a 45

degree angle or with swing for Laundry mode

UV LIGHT (Air purier function)

To activate the UV function press the "UV" button and the indicator light

will illuminate. The Germicidal UV light will destroy germs, bacteria, fungi

improving the indoor air quality

HUMIDITY SETTING

Press the UP and DOWN buttons to select the desired relative humidity

level, the default relative humidity is 55%. When a relative humidity of 35%

is selected, the compressor will not stop until the water tank is full.

NOTE: The desired humidity cannot be changed in SMART mode.

TIMER

Press the TIMER button to program the timer. When the timer is activated

the "TIMER" light will be illuminated. Before programming the timer, ensure

the timer function has not been activated (the light must be off). The

following timer programs are available.

DELAYED POWER-ON FUNCTION: With the appliance in stand-by, press

the TIMER button, then use the UP and DOWN buttons to set in how many

hours time you require the unit to start (1~24 hours).

DELAYED POWER-OFF FUNCTION: While the appliance is running with

the desired settings, press the TIMER button, then use the UP and DOWN

buttons to set in how many hours time you require the unit to stop (1~24

hours).

DEFROST

INTELLIGENT DEFROST

The appliance will defrost automatically when the coil sensor detects that

the internal temperature is too low. During defrosting the indicator will light

up. Once the defrost cycle has finished, the appliance will return to the

mode that was previously operating.

TANK FULL

TANK-FULL

When the water tank is full, the TANK FULL indicator light will flash, and

the unit will stop operating. One emptied and replaced, the appliance will

resume operation.

OPTIONAL CARBON FILTER (Air purication function)

Remove the carbon lter from the bag and insert it on the lter housing. It is

suggested to hoover the carbon lter every 2-3 weeks and change it every

3-6 months as this will help to ensure the room is kept fresh and odour free.

0807

Power Button: Press to turn the dehumidier on and off.

Oscillation Button: Press once to make the louvre swing and press again to lock

at 45 degrees, press again to lock at 90 degrees. Do not operate the unit if the self-

opening louvers do not open on power on.

Timer: Press the timer button, then use the buttons to adjust the

duration of the timer (1-24 hrs, start/ stop timer).

If set while the unit is running: The number will represent the number of hours the unit will

operate before turning off. This will not be affected if the unit enters defrost mode or the tank

is emptied and reinserted.

If set while the unit is in standby: the set number represents the period in hours after which

the unit will start. To cancel start / stop mode press the timer key again.

Up and Down Buttons: During the High or Low modes when the unit is

displaying the current relative humidity, these buttons can be used to adjust

the desired humidity level. The desired relative humidity can be set between

35 and 80% in 5% increments.

SMART Mode: This is designed for maximum convenience and

maintains the ideal domestic environment humidity level of 50-55%

while saving electricity. This is the default mode and is recommended for

most users.

During operation the compressor will operate until the desired humidity is reached and then

will stop. The economical low air purier mode will continue to operate. The fan moves the

air around the room ensuring the entire air in the room is processed and humidity correctly

measured.

To achieve drier air, or while drying laundry, put the unit in High mode and use the down

button to select a lower desired humidity (e.g. 35-45%).

LAUNDRY MODE: When drying clothes it is advised for the dehumidifier to operate

continuously with maximum water extraction until the water tank is full. Set the unit to the

High mode, and set the desired humidity level between 35%-50%. 35% is very dry and is

hardly achievable in a UK domestic environment. As such the unit will work until water tank

is full when set to 35%. Set the louvres to swing mode or to 45 degrees directing the airow

onto the clothes. Do not place clothes directly over any of the vents on the dehumidifier.

Make sure that there is nothing blocking the hot air exhaust air ow and for best results place

the laundry within 1.5 meters of the dehumidier.

NOTES:

POWER

OSC

TIMER

QUICK REFERENCE GUIDE

Air Purifier

If a permanent drainage pipe is tted the unit will not stop operating. Setting the desired

humidity to around 35% is good for laundry mode, a quick drying boost, or in emergencies.

It is not recommended for long normal operation in a domestic or ofce environment.

To allow more moisture in the air, press the up button and set to a higher desired humidity

(e.g. 60-70%).

We recommend setting the Humidity to 50-55%. This is great for domestic operation and

dry storage

Setting the humidity to 60% is great for personal comfort and applications where 50% RH

is considered too dry

Setting the humidity to 70% is ideal for unoccupied properties or where an economical run

is needed without the need to reduce the humidity further.

•

1009

TANK FULL LIGHT

When the water tank is full, removed or incorrectly inserted the unit will stop dehumidifying,

the red tank full light will illuminate and the unit will beep. Empty the tank and reinsert it

correctly to resume operation.

AUTO DEFROST

When frost builds up on the evaporator coils, the compressor will cycle off and the unit will

go in to defrost mode. Following completion of the defrost mode, the unit will return to the

previously operating settings.

AUTO-RESTART (on some models)

If the unit stops unexpectedly due to the power cut, it will restart with the previous function

selected automatically when the power resumes, and the 3 minute compressor protection

has elapsed.

POWER

After the unit has stopped, to protect the compressor it is not recommended to resume

operation for at least 10 minutes. Operation can resume after this period lapses. When the

unit is restarted there is a 3 minutes delay before compressor will start.

LIGHTWEIGHT PORTABLE DESIGN ON CASTORS

The dehumidier is built to be compact and lightweight. The castors on the bottom of the unit

make it easy to move from room to room.

Your dehumidier contains an advanced micro-CPU controlled device which is capable of

self-diagnostics. The LCD display may also show the error and protections codes.

HUMIDISTAT CONTROL AND FAN/COMPRESSOR OPERATION

OTHER FEATURES AND INDICATORS

When the unit is running in a room with a temperature between 5

C and 12

C, it will enter

defrost mode roughly every 30 minutes.

When the unit is running in a room with a temperature between 12

C and 20

C, it will enter

the defrost mode roughly every 45 minutes.

When the humidity of the room is 2% lower than the desired humidity the compressor will

turn off automatically but the fan will continue to operate to ensure that the air within the

room is not stale. The unit will use only a minimal amount of energy in fan mode.

When the humidity of the room is equal to or higher than the desired humidity the

compressor will restart after a 3 minutes delay to protect the compressor.

•

1009

A badly positioned dehumidifier will have little effect. In positioning the dehumidifier

please ensure circulation of air in not restricted around the unit.

Allow at least 20 cm space around the unit.

This dehumidifier is designed only for indoor

residential or small ofce applications and any

commercial or industrial use will invalidate the

warranty.

Use in an enclosed area for maximum

efficiency. Close all doors, windows to create

an effective operating environment. Do not use

outdoors.

Your electriQ dehumidifier will begin to

protect your space from the harmful effects of

excessive moisture as soon as it is turned on. Excess moisture is dispersed throughout

your home. For this reason, the dehumidier should be positioned in a central and clear

location so that it can draw this moist air towards it from all over the home. A warm

hallway or landing is an excellent position for your dehumidier. If possible, leave interior

doors ajar to allow air circulation.

Alternatively, if you have a serious problem in one area you can begin by positioning the

dehumidier there and moving it to a more central location at a later date. For the most

effective use, run your dehumidier with external doors and windows kept closed. Please

note the unit should not be placed directly against a radiator or other heat source.

When positioning your electriQ dehumidier, ensure that it is placed clear of any obstacle

that may limit the air movement. Place the dehumidier on a at dry surface.

Note: Do not force castors to move over carpet or uneven surfaces, nor move the unit

with water in the tank as it may tip over and spill water.

20cm

POSITIONING THE DEHUMIDIFIER

1211

When the water tank is full, the unit will stop automatically. When this happens the TANK

FULL red light will show on the control panel, and the unit will bleep.

NOTE: Only empty the water tank when it is full or before moving or storing the unit.

There are two ways to dispense collected water.

1. USE THE TANK

When the tank is full, the unit will automatically stop running,

and the Tank Full indicator will ash.

Slowly pull out the tank. Grip the tank by its handle securely,

and carefully pull it out. Empty the water tank and reinsert it

into the dehumidier. The tank must be in place and securely

seated for the dehumidier to operate again. The dehumidier

will re-start when the tank is restored in its correct position.

NOTES:

When you remove the water tank, do not touch sensors or any parts which are situated

behind tank. Doing so may damage the product. Be sure to push the tank gently all the

way into the unit. Banging the bucket against anything or failing to push it in securely into

place may cause the unit not to operate.

Do not remove any parts from the water tank or tank enclosure. The water full sensor will

no longer be able to detect the water level correctly and water may leak from the water

tank.

2. CONTINUOUS DRAINAGE

Water can be automatically plumbed in or drained into a sink, a larger recipient or

through the wall into an outside drain by attaching a pipe to the unit (10 mm internal

diameter) (not included). Insert the pipe into the drain outlet at the back of the unit as

shown here.

Make sure the connection between pipe and the drain outlet is tight and does not leak.

Then direct the pipe to a suitable drainage point. This unit uses gravity to dispose of

water hence the drain should be lower than the water outlet on the unit. Put the tank

back. Be sure to run the water pipe downward and let the water to ow out smoothly. Do

not kink or bend the pipe.

The permanent drain can be used in conjunction with a water pump (e.g. when draining

from a cellar) to lift the water upwards.

OTHER FEATURES AND INDICATORS

1211

Always shut off the unit and unplug from the mains before cleaning or performing any

maintenance. When it is not in use for long periods it is advisable to remove the plug

from the power socket. Do not use chemical solvents (such as benzene, alcohol or

gasoline) as they may cause irreversible damage to the unit.

1. CLEAN THE GRILLE AND CASE

Use water and a mild detergent to clean

the washable mesh lters. Do not use

bleach or abrasives. Do not splash

water directly onto the main unit. Doing

so may cause an electrical shock and

can lead to the insulation to deteriorate,

or cause the unit to rust. The air intake

and outlet grilles get soiled easily, so

use a vacuum attachment or soft brush

to clean. Wipe the dehumidifier body

with a soft damp cloth or kitchen towel.

Remove the ABS lter frame. If the optional carbon lters are tted, remove them from the

frame and hoover gently approcimately every 2-3 weeks.

If the mesh lter is dirty hoover it, if it is heavily soiled wash it with warm soapy water and dry

thoroughly before reinserting it in the unit.

When lter cleaning is nished and lters are dry placed them back into the unit.

NOTE: While the carbon filter is optional never run the unit without the mesh filter frame

correctly inserted.

2. CLEAN THE WATER TANK

Every few weeks, clean the tank to prevent growth of mould, mildew and bacteria. Partially ll

the tank with clean water and add a little mild detergent. Swish it around and than empty the

tank and rinse.

NOTE: Do not use a dishwasher to clean the tank. After cleaning and drying, the tank must

be reinserted securely into dehumidier in order to restart operation.

END OF SEASON MAINTENANCE

1. Empty and clean the water tank.

2. Clean the unit and the lters as per cleaning procedure above.

3. Coil the power cord on the special cord storage rest at the back of the unit

4. Cover the unit and keep it in a dry place.

CARE AND MAINTENANCE

1413

FREQUENTLY ASKED QUESTIONS

Why doesn't the dehumidier seem to extract much water if the temperature is low?

This is a compressor dehumidifier which works best in temperatures above 15

C. If the

temperature is low and the air is dryer than the setting on the humidistat the unit will not

extract water. If you want to use a dehumidier for outside buildings, unheated properties,

boats or garages please check our desiccant range.

Why doesn't the unit work /or stops suddenly?

The water tank may be full or displaced. To rectify: empty the tank and carefully place the

tank back in the unit. Also the unit may be running in dehumidifying mode with a low room

temperature. Please check if the room temperature is lower than 5

C. If so, the unit will stop

working while in dehumidifying mode. (unit may be defrosting).

The ambient operating range is between 5

C and 35

C with a relative humidity ranging from

30% to 80%. For maximum efciency use the unit between 15

C and 32

Sometimes cold and/or hot air comes out from the air outlet grill, why?

When the unit is in dehumidifying mode it absorbs humid air from room and freezes it to

reduce the humidity.

During the cold cycle there should be cold air coming out of the unit

During the hot cycle hot dry air should be coming out of the outlet grill.

TROUBLESHOOTING

：

Issue Cause Solution

Hot or cold air

being produced

Normal Operation When the unit is in dehumidifying mode it absorbs humid air from room and

freezes it to reduce the humidity.

During the cold cycle there should be cold air coming out of the unit

During the defrost cycle hot dry air should be coming out of the outlet grill.

Unit does not

operate

Is the plug properly

inserted in the socket?

Insert the plug into the socket and turn the switch on.

Does the tank full

indicator is red?

Tank full, oat displaced or tank not properly inserted. Empty tank, check oat

and make sure tank is properly inserted in unit.

Front louvres do

not open

Louvre motor is blocked Check if anything is blocking the louvre

Try to move gently the louvres up and down while the unit if off

If the above fails return the unit to service centre

Dehumidier

does not

extract water

Is the unit set to a

humidity level lower

than the one in the

room?

Set the humidity level on the humidistat bellow current humidity reading.

Is the temperature too

low for water extraction

to be efcient?

Increase temperature in the room or reposition the unit.

Is any intake grill or

discharge blocked? Is

the unit too close to

walls.

Remove obstructions and restart the unit.

Ensure a distance of at least 20 [cm between the unit & walls

Airow seems

weak

Is lter dirty or clogged? Please service the lters regularly as per user manual.

Unit is noisy

during operation

Is the unit on an

uneven surface?

Please place on at horizontal surface.

Is lter clogged? Please service the lters regularly as per user manual.

E3 or E4 Humidity sensor error Use the unit within the prescribed humidity range. Unplug the unit, rest and plug

it back in. If error repeats, call for service centre.

E1 or E2 Temperature sensor

error

Use the unit within the prescribed temperature range. Unplug the unit, rest and

plug it back in. If error repeats, call for service centre.

E5 or E6 Abnormal Coil sensor

temperature or current

Use the unit within the prescribed humidity and temperature range. Unplug the

unit, rest and plug it back in. If error repeats, call for service centre.

Defrost light on

and unit

stops regularly

Unit is defrosting Allow the unit to automatically defrost. The protection will clear after the unit self

defrosts. Increase temperature in the room if this repeats too often

Tank full red

light

Water tank full

notication

Tank is full or is not in the right position-- Empty the tank and replace in the right

position.

Any other malfunctions will need to be reported to electriQ service centre. Do not attempt unauthorised repairs as these may

invalidate the warranty.

1413

Technical data

Model CD12LE-V3 CD20LE-V3

Voltage 1Ph, 220-240V~ 50Hz 1Ph, 220-240V~ 50Hz

Dehumidifying capacity

12 L / day

(at 30

C / 80%RH)

20 L / day

(at 30

C / 80%RH)

Fan Speeds 2 2

Power Consumption 180W 270W

Running Amps 0.91 Amps 1.2 Amps

Tank Capacity 4 litres 4 litres

Humidity settings range 35%~80% 35%~80%

IP RATING IPX1 IPX1

Refrigeran R290, 60 grams R290, 75 grams

Airow m

/h 180 180

High / Low Pressure 1.5/0.5MPa 1.5/0.5MPa

Max noise level dB(A) 42-49 42-49

Filters carbon (optional) carbon (optional)

Dimensions mm

(WxDxH)

380x580x195 380x580x195

Weight kgs 14.3 14.3

GWP 3 3

All information provided is for reference only. Products specications may change due to continuous

product development.

Disposal: Do not dispose this product as unsorted waste. Collection of such waste

must be handled separately as special treatment is necessary.

Recycling facilities are now available for all customers at which you can

deposit your old electrical products. Customers will be able to take any

old electrical equipment to participating sites run by their local councils.

Please remember that this equipment will be further handled during

the recycling process, so please be considerate when depositing your

equipment. Please contact the local council for details of your local

household waste recycling centres.

electriQ UK SUPPORT

www.electriQ.co.uk/support

Please, for your own convenience, make these simple checks before calling the

service line.

1. Has the unit been standing upright for at least 2 hours?

2. Is the unit plugged into the mains?

3. Is the fuse OK?

4. Switch the unit off and wait three minutes to see if the issue is resolved. Restart the unit.

5. Check if the water tank is full.

6. Was the troubleshooting guide followed?

If the unit still fails to operate call: 0871 620 1057 or complete the online form

Ofce hours: 9AM - 5PM Monday to Friday

Unit J6, Lowelds Business Park,

Lowelds Way, Elland

West Yorkshire, HX5 9DA

ElectrIQ CD12LE User manual

Brand: ElectrIQ

Model: CD12LE

Category: Dehumidifiers

Type: User manual

This manual is also suitable for

CD20LE

Download PDF

report

ElectrIQ CD12LE User manual

This manual is also suitable for

ElectrIQ CD12LE User manual

Related papers

Other documents