Optimus ME-200C User manual

Brand: Optimus

Model: ME-200C

Category: Musical Equipment

Type: User manual

Optimus ME-200C is a microphone desk and voice alarm fireman's panel with CAN Bus communications for COMPACT Systems. Here's an overview of its features and use cases:

Microphone console: Send live messages and repetitions to predetermined zones. Voice alarm panel: Remotely activate warning and evacuation messages housed in a COMPACT matrix, and launch live announcements to a group of preset zones. Emergency mode: Activate with a key switch. Speech filter, compressor, microphone volume adjustment, and dynamic microphone. Surveillance of microphone capsule, communication with audio matrix, and internal status surveillance.

Optimus ME-200C is a microphone desk and voice alarm fireman's panel with CAN Bus communications for COMPACT Systems. Here's an overview of its features and use cases:

9I327 17/03/2017 V3.1.000

MD-30C version 3.1.000

Microphone desk and

voice alarm fireman's panel

ME-200C

Table of contents

1. INTRODUCTION ..................................................................................................................................................................... 4

2. FRONT VIEW .......................................................................................................................................................................... 4

3. REAR VIEW ............................................................................................................................................................................ 6

4. CONFIGURATION ................................................................................................................................................................... 7

5. CONNECTION......................................................................................................................................................................... 8

5.1. Power supply ................................................................................................................................................................. 8

5.2. Audio and CAN bus connection ..................................................................................................................................... 8

5.2.1. CAN Bus and audio connection between ME-200C and COMPACT unit ...................................................... 9

5.2.2. CAN Bus and audio connection between several ME-200C ......................................................................... 9

5.2.3. Connection between ME-200C and COMPACT-E expansion unit .............................................................. 10

6. COMMISSIONING THE UNIT ................................................................................................................................................. 11

7. WORK MODES ..................................................................................................................................................................... 11

8. NORMAL MODE OPERATIONS ............................................................................................................................................. 11

8.1. Sending a live voice announcement ............................................................................................................................ 11

8.2. Repeat function ........................................................................................................................................................... 11

9. OPERATIONS IN EMERGENCY MODE .................................................................................................................................... 12

9.1. Entering the Emergency Mode .................................................................................................................................... 12

9.2. Activating a WARNING message .................................................................................................................................. 12

9.3. Activating an EVACUATION message........................................................................................................................... 12

9.4. Sending a live voice message in Emergency Mode ...................................................................................................... 12

9.5. Repeat function in Emergency Mode .......................................................................................................................... 12

9.6. Exiting the Emergency Mode ....................................................................................................................................... 12

10. SYSTEM ALARMS ................................................................................................................................................................. 13

11. DIMENSIONS ....................................................................................................................................................................... 13

12. TECHNICAL CHARACTERISTICS ............................................................................................................................................. 14

13. SOFTWARE AND FIRMWARE VERSIONS ............................................................................................................................... 14

14. DOCUMENT VERSION TRACKING ......................................................................................................................................... 14

15. GUARANTEE ........................................................................................................................................................................ 15

WARNING. This is a Class A unit. In a domestic environment this unit may cause radio interferences. In this case the user

must take the necessary precautions.

MD-30C version 3.1.000

Microphone desk and

voice alarm fireman's panel

ME-200C

1. INTRODUCTION

Microphone desk and voice alarm fireman’s panel with CAN Bus communications for COMPACT Systems.

As a microphone console, it allows the user to send live messages and repetitions to predetermined zones. As a voice alarm panel

allows the remote activation of warning and evacuation messages housed in the COMPACT matrix, as well as to launch live an-

nouncements, to a group of preset zones.

Access to the emergency mode is protected by a key switch.

Principal characteristics:

Activation of emergency mode by key.

WARNING Message activation button.

EVACUATION Message activation button.

Emergency mode exit button.

Dynamic microphone.

Communication with the COMPACT audio matrix via CAN

bus.

Input & output RJ45 connectors for audio and communi-

cation signals.

Warning and Evacuation pre-recorded messages housed

in the COMPACT unit.

Announcements with or without a pre-announcement

tone and final tone (Gong).

3 or 4 tones configurable Gong.

Repeat Key, for repetition of the last live voice message.

Speech filter.

Compressor.

GONG volume adjustment.

Microphone volume adjustment.

Capsule surveillance.

Internal status surveillance.

Generic fault, internal error and microphone capsule

error or communication error with audio matrix LEDs in-

dicators.

Acoustic alarm indicator.

Microphone audio level indicator.

Every COMPACT matrix unit allows connecting 16 units of

ME-200C microphone desks.

2. FRONT VIEW

(1) Microphone

(2) EMERGENCY LED. Lights up when the emergency mode is

activated from the desk or from any other element of the

system. The LED remains illuminated while the system is in

Emergency Mode.

(3) Lock and Key to access the EMERGENCY MODE. Switches

to Emergency Mode. If activated, the LOGGED LED lights up

and the WARNING, EVACUATION and RESET emergency

buttons become operative.

After 60 seconds without any operation from the desk (this

time can be modified by the Call Point software), the LOGGED

LED goes off and the emergency buttons of the microphone

desk are no longer operative, being necessary to activate the

key again to operate with the microphone desk.

Includes two keys.

(4) WARNING push-button. Activate the warning message.

Incorporates a push-button ON indicator light.

(5) EVACUATION push-button. Activates the evacuation

message. Incorporates a push-button ON indicator light.

(6) RESET push-button. End Emergency Mode.

(7) REPEAT Key. Key for repeating the last live voice message

that was sent.

(8) TALK Key. Is used to send live voice announcements. It

must remain pressed while talking.

(9) GONG+TALK Key. Is used to send live voice

announcement preceded by a gong. It must remain pressed

while talking.

MD-30C version 3.1.000

Microphone desk and

voice alarm fireman's panel

ME-200C

(10) GENERIC FAULT indicator. System alarm indicator.

(11) LOGGED LED. Indicates that the Emergency Mode

has been activated from the microphone desk itself through

the emergency key. The system is in emergency mode and

the microphone desk buttons are operative.

(12) CPU FAULT LED. Indicates internal error of the

application.

(13) POWER LED. Indicates that power is applied to the

paging desk.

(14) LOCAL FAULT LED. Indicates microphone capsule error

or communication error with audio matrix.

(15) TALK / REPEAT LED. Illuminates when TALK or

GONG+TALK is pressed, indicating that you can begin

speaking. When the REPEAT key is pressed, it indicates that

the repeat message is playing.

(16) GONG LED. When illuminated, it indicates that the

paging desk is generating the GONG.

(17) BUSY LED. When lit, it indicates that the system is busy.

(18) MIC LEVEL LEDs. They indicate the audio level of the

microphone or the repeat message that is playing. The LED

marked as Peak indicates that the signal is saturated. This LED

should never light up.

Figure 1

MD-30C version 3.1.000

Microphone desk and

voice alarm fireman's panel

ME-200C

3. REAR VIEW

(1) Ground connection.

(2) Power supply fuse (0.5A).

(3) 24 VDC Power supply input (see section 5.1.).

(4) Configuration DIP switches (see section 4).

DIP switch 1. RJ45 SHLD-GND LINK. Allows separating the PIN

8 and the shield of the RJ45 connectors from the ME-200C

internal ground (GND).

DIP switches 2 and 3. BUS CAN END. Configure DIP switches

2 and 3 to indicate the position on the CAN bus occupied by

the ME-200C (end element or intermediate element). If the

microphone desk is the final bus element, set these DIP

switches to ON position. If it is an intermediate element, set

them OFF.

DIP switches 5, 6, 7 and 8. CAN ADDRESS. The microphone

desk communicates with the COMPACT system through a

CAN bus. Each ME-200C connected to the CAN bus must have

a different communication address. These DIP switches allow

you to assign this address.

(5) INPUT and (6) OUTPUT connectors.

RJ45 Connectors. They are used to connect the equipment to

the COMPACT system. They transmit and receive the audio

and CAN data signals.

To connect them follow the section 5.2. Audio and CAN bus

connection.

The combination of the INPUT and OUTPUT connectors allow

the connection of several ME-200C microphone desks (up to

a maximum of 16) forming a BUS between elements. See

section 5.2.2. CAN Bus and audio connection between several

ME-200C.

(7) GONG volume.

(8) Microphone volume.

Figure 2

MD-30C version 3.1.000

Microphone desk and

voice alarm fireman's panel

ME-200C

4. CONFIGURATION

Use the DIP switches on the back of the microphone to configure it:

DIP switch 1. RJ45 SHLD-GND LINK. Allows separating the PIN 8 and the shield of the RJ45 connectors from the ME-200C internal

ground (GND).

DIP switches 2 and 3. BUS CAN END. Configure DIP switches 2 and 3 to indicate the position on the CAN bus occupied by the ME-

200C (end element or intermediate element). If the microphone desk is the final bus element, set these DIP switches to ON. If it is

an intermediate element, set them OFF.

DIP switch 4. No used.

DIP switches 5, 6, 7 and 8. CAN ADDRESS. The microphone desk communicates with the COMPACT system through a CAN bus.

Each ME-200C connected to the CAN bus must have a different communication address. Assign an address between 0 and 15.

CONNECTION TO GND

OF PIN 8 AND SHIELD OF

RJ45 CONNECTORS

BUS CAN END

ON/OFF

BUS CAN

ADDRESS

CONNECTED

NOT CONNECTED

END POSITION.

BUS CAN END: ON

INTERMEDIATE POSITION.

BUS CAN END: OFF

* FACTORY SETTINGS

MD-30C version 3.1.000

Microphone desk and

voice alarm fireman's panel

ME-200C

5. CONNECTION

5.1. Power supply

The microphone desk should be powered at 24VDC through the DC IN 24V terminal strip on the back plate.

5.2. Audio and CAN bus connection

Through the RJ45 INPUT and OUTPUT connectors, the console transmits and receives CAN communication and audio signals to the

COMPACT system. For connection use RJ45 connectors with metal housing and STP CAT 5 cable.

Pin 1: AUDIO H (HOT)

Pin 2: AUDIO C (COLD)

Pin 3: Not used

Pin 4: CAN H

Pin 5: CAN L

Pin 6: Not used

Pin 7: Not used

Pin 8:

Metal Shield:

24V DC

POWER SUPPLY

I924UP

(Not included)

GND

DIP switch 1

Figure 3

Figure 4

MD-30C version 3.1.000

Microphone desk and

voice alarm fireman's panel

ME-200C

5.2.1. CAN Bus and audio connection between ME-200C and COMPACT unit

Figure 5 shows the most common connection

between an ME-200C and the COMPACT audio

matrix with the UMX-EA3 input card. To facilitate

the connection it is recommended to use an

Optimus Z-52A patch panel or similar.

5.2.2. CAN Bus and audio connection between several ME-200C

Use the INPUT and OUTPUT connectors to connect

various (up to a maximum of 16), forming a BUS

between elements.

Figure 5

Figure 6

CAN End

termination = ON

CAN End

termination = OFF

CAN End

termination = OFF

(RJ45 Connector

front view)

To UMX-EA3 card

To COMPACT unit

From RJ45 OUTPUT

ME-200C

(RJ45 Connector

front view)

MD-30C version 3.1.000

Microphone desk and

voice alarm fireman's panel

ME-200C

5.2.3. Connection between ME-200C and COMPACT-E expansion unit

The CAN communication speed of the ME-200C is 33.3

kbit/s. For installation with COMPACT-E expansion units

with a communication speed of 500 kbit/s, a CAN-AV

speed adapter (code A465AV) must be inserted in the

bus to match the transmission speed between devices.

The attached table shows the transmission speed of the

equipments:

To connect an ME-200C to the COMPACT-E follow

figure 7.

EQUIPMENT

SPEED TRANSMISSION

COMPACT

33.3 kbit/s o 500 kbit/s (built-

in speed adapter )

COMPACT-E

500 kbit/s

MD-30C

33.3 kbit/s

ME-200C

33.3 kbit/s

NS-CAN

33.3 kbit/s

(RJ45 Connector

Front view)

To UMX-EA3 card

To COMPACT-E

expansion unit

From RJ45 OUTPUT

ME-200C

(RJ45 Connector

Front view)

Figure 7

24V DC

POWER

SUPPLY

MD-30C version 3.1.000

Microphone desk and

voice alarm fireman's panel

ME-200C

6. COMMISSIONING THE UNIT

Commissioning the unit requires sending of configurations to the COMPACT audio matrix to whose CAN bus the ME200C is con-

nected. To do this, you need a PC equipped with a network card and connected to the COMPACT matrix, either through a ethernet

switch, or directly through a network cable. The PC must have the Call Point software installed.

1. Set the CAN address of the ME-200C and its position in the BUS (end or intermediate element) according to section 4.

CONFIGURATIONS.

2. Make the connections between units.

3. Apply power to the units.

4. Via the Call Point software, configure the parameters of theME-200C and send the configurations to the COMPACT unit.

7. WORK MODES

There are two distinct work modes: Normal and Emergency modes. Normal mode is the default working mode. Using a key switch

accesses Emergency Mode.

Normal Mode:

It allows you to send live messages and replays of those messages. The destination zones of the messages are predetermined via

the Call Point software.

Emergency Mode:

It has a warning message push-button, an evacuation message push-button and microphone for live messages. Access to the emer-

gency mode is protected by a key switch.

The WARNING and EVACUATION messages are assigned and configured via the Call Point software

All the emergency messages (live messages as well as pre-recorded WARNING and EVACUATION messages) will be broadcast to the

Associated Group. The Associated Group must have been previously configured via the Call Point software.

NORMAL MODE

EMERGENCY MODE

Default mode

Access to emergency mode with key switch

Messages are sent to the predetermined zones previously

configured via Call Point software

Messages are sent to the Associated Group (predetermined

group via Call Point software)

Allows live voice messages

There is a REPEAT key whose function is to repeat the last live message.

WARNING push-button non operative

WARNING push-button activates the warning message

EVACUATION push-button non operative

EVACUATION push-button activates the evacuation message

RESET push-button non operative

RESET push-button to exit emergency mode

8. NORMAL MODE OPERATIONS

8.1. Sending a live voice announcement

1 Press and hold GONG+TALK (or TALK).

2 You can begin speaking when the blue TALK LED

illuminates.

3 To finish the broadcast, release the GONG+TALK (or

TALK).

8.2. Repeat function

The microphone desk incorporates a function that enables to

repeat the last live voice message that was sent.

To activate select the REPEAT key. The TALK/REPEAT

indicator light remains illuminated while the message is being

repeated.

You can stop a repeat message that is being played by press-

ing the REPEAT key again.

MD-30C version 3.1.000

Microphone desk and

voice alarm fireman's panel

ME-200C

9. OPERATIONS IN EMERGENCY MODE

9.1. Entering the Emergency Mode

Insert the key into the lock and turn 90° clockwise. The

LOGGED LED should light up.

9.2. Activating a WARNING message

1. Press the WARNING button (the system must be in

Emergency Mode). The WARNING button indicator light

illuminates and the warning message begins to play.

2. Press the RESET button to stop the message. The system

exits the Emergency Mode.

If an EVACUATION message is played while the WARNING

message is playing, the WARNING message will stop.

If a live voice message is sent while the WARNING message is

playing, the WARNING message stops playing while the live

voice announcement is being broadcast. When the live voice

message ends, the WARNING message will automatically

resume playing.

9.3. Activating an EVACUATION message

1. Press the EVACUATION button (the system must be in

emergency mode). The EVACUATION button indicator

light illuminates and the evacuation message begins to

play.

2. Press the RESET button to stop the message. The system

exits the Emergency Mode.

The EVACUATION message takes priority over the WARNING

message: the activation of the evacuation message stops the

WARNING message.

If a live voice message is sent while the EVACUATION

message is playing, the EVACUATION message stops playing

while the live voice announcement is being broadcast. When

the live voice message ends, the EVACUATION message will

automatically resume playing.

9.4. Sending a live voice message in

Emergency Mode

1. With the microphone desk in emergency mode, press and

hold the GONG+TALK (or TALK) button.

2. You can begin speaking when the TALK indicator light

illuminates.

3. To finish the broadcast, release the button.

Live voice announcements take priority over an EVACUATION

message and in turn, an EVACUATION message takes priority

over a WARNING message.

9.5. Repeat function in Emergency Mode

With the microphone desk in emergency mode, select the

REPEAT key. The TALK/REPEAT indicator light up while the

message is being repeated.

You can stop a repeat message that is being played by press-

ing the REPEAT key again

9.6. Exiting the Emergency Mode

Press the RESET key. The EMERGENCY button light goes out

to indicate that the desktop paging system is no longer in

Emergency Mode

All the emergency messages (live messages as well as pre-recorded WARNING and EVACUATION messages) will be broadcast to

the ASSOCIATED GROUP. The ASSOCIATED GROUP must have been previously configured via the Call Point software.

The WARNING and EVACUATION messages are assigned and configured via the Call Point software

The WARNING, EVACUATION and RESET pushbuttons are not operative until emergency mode is entered using the key.

In EMERGENCY MODE, live voice announcements take priority over an EVACUATION message and in turn, an EVACUATION

message takes priority over a WARNING message.

After 60 seconds without any operation from the desk (this time can be modified by the Call Point software), the LOGGED LED

goes off and the emergency buttons of the microphone desk are no longer operative, being necessary to reactivate the key

switch to operate again with the microphone desk.

MD-30C version 3.1.000

Microphone desk and

voice alarm fireman's panel

ME-200C

10. SYSTEM ALARMS

The microphone desk incorporates several alarm indicators:

LOCAL FAULT indicator: Front yellow LED. Indicates microphone capsule error or communication error with audio matrix.

CPU FAULT indicator: Front yellow LED. Illuminates when the microphone desk detects an internal application error (firmware).

GENERIC FAULT indicator: Front yellow LED. Illuminates when the microphone desk receives one or several alarms from the

system.

Acoustic alarm indicator (buzzer): Acoustic indication that is generated by the unit when it receives an alarm. The acoustic

indication is a buzzing sound that lasts 10 seconds and is periodically repeated every 20. This acoustic indication may be

deactivated through the Call Point software.

11. DIMENSIONS

MD-30C version 3.1.000

Microphone desk and

voice alarm fireman's panel

ME-200C

12. TECHNICAL CHARACTERISTICS

ME-200C

Inputs

1 Input, through RJ45 connector

Outputs

1 Output, through RJ45 connector

Power supply

24 VDC

Consumption

150 mA

Weight

1.7 kg

Finishes

Desk: RAL7021 Bayblend plastic

Flexo MICROPHONE

Capsule

Dynamic

Polar diagram

Unidirectional

Frequency response

150 Hz 12 kHz

Sensitivity

2.2mV/Pa/1kHz

Output impedance

500 Ohm 30% (at 1kHz)

Material

Aluminium

13. SOFTWARE AND FIRMWARE VERSIONS

The functionalities described in this user manual are valid for software and firmware versions that are the same or later versions of:

ME-200C Firmware

5.3

COMPACT Firmware

Application version 3.1.4877

Linux version 2.6.35.14

Call Point Software

Version 3.1.4869

Optimus Flasher Software

Version 2.9.12

14. DOCUMENT VERSION TRACKING

Reference system

Type of Document

Confidentiality

N/A

COMPACT/ME-200C

Installation and operation guide

Rev

Date

Modifications Content

Written by:

3.1.000

March 2017

Translation of the Spanish language version 3.1.000

R+D Department

Approved by

Function

Date

Ferran Gironès i Puig

R+D Director

03/2017

MD-30C version 3.1.000

Microphone desk and

voice alarm fireman's panel

ME-200C

15. GUARANTEE

1. GUARANTEE CERTIFICATE

1. OPTIMUS S.A. guarantees that its products are free from material and

manufacturing defects when they are first delivered to the purchaser.

2. In accordance with the conditions outlined here, OPTIMUS S.A. guarantees

its products for two (2) years from the date on which the purchaser acquires the

product. If, within this guarantee period, defects appear which are not due to

factors outlined in section 2, OPTIMUS S.A. shall replace or repair the unit using

equivalent, new or reconstructed replacement parts, as it deems fit. If

replacement parts are applied which improve the unit, OPTIMUS S.A. reserves

the right to charge the client for the additional cost of these components.

3. No guarantee benefits shall be provided other than those cited here.

4. In order to claim the guarantee rights, it shall be an essential requirement

to present the original purchase invoice or the guarantee certificate.

2. GUARANTEE PROVISIONS

1. In the event that the product had to be modified or adapted to comply with

local requirements concerning technical specifications or safety, and if the

country in question is not the country for which the product was originally

designed and manufactured, defects are not considered to be material or

manufacturing defects. Furthermore, the guarantee does not cover the

execution of these modifications or adaptations, regardless of whether or not

they have been carried out correctly.

Nor shall OPTIMUS S.A. be responsible for any costs under this guarantee for

these types of modifications.

2. The guarantee shall not entitle the purchaser to inspection or free

maintenance or repair of the unit, particularly if the defects are due to

inappropriate use. Nor do the guarantee rights cover defects in wearing parts

that become worn as a result of normal wear and tear. Wearing parts are, in

particular, potentiometers, switches/keys, and similar parts.

3. The guarantee does not cover defects in the equipment unit caused by:

Abuse or incorrect use of the unit for purposes other than those for which it

is intended, in non-compliance with the service and maintenance

instructions specified in the Manual and/or Technical Instructions for the

unit.

Connection or use of the product in a manner that does not correspond to

the technical or safety requirements of the country in which the unit is

used.

Installation in conditions other than those indicated in the Manual and/or

Technical Instructions.

Deficiency or interruptions in the electricity supply or installation defects

which imply use in abnormal conditions.

Damage caused by other equipment units that are connected to the

product.

The use or installation of Software (programmes), interfaces, parts or

supplies not provided and/or not authorised by OPTIMUS S.A.

Failure to use the original packaging for transportation.

Damage caused by force majeure or other causes not attributable to

OPTIMUS S.A.

4. The following elements are not covered by this guarantee:

All plastic surfaces and all parts exposed to outdoor conditions which have

been scratched or damaged as a result of normal or abnormal use.

Breakages, knocks, damage due to a fall or scratches caused by moving the

unit in any way.

Damage caused by tests, use, maintenance, installation or inappropriate

adjustments, or as a result of any alteration or modification of any kind not

carried out by a Service Authorised by OPTIMUS S.A. in compliance with this

guarantee.

Damage to persons or property that might be caused by the improper use

of the equipment, including lack of maintenance.

5. The guarantee shall not be valid whenever the following is observed:

Amendments or corrections made to the details of the guarantee certificate

or purchase invoice.

Failure to produce the original invoice or the absence of a date on this.

Absence of the serial or batch number on the equipment.

6. In the case of personal computers, the guarantee will not cover the

elimination of computer viruses, the restoration of programmes damaged by

these or the reinstallation of the disk following its deletion.

7. The rights of this guarantee are invalidated if the product has been repaired

or opened by staff unauthorised by OPTIMUS S.A. or by the client himself.

8. If OPTIMUS S.A. were to establish before the client that the damage

affecting the unit does not entitle a claim to be made under the guarantee, the

costs of checking the equipment incurred by OPTIMUS S.A. shall be borne by the

client.

9. Products not covered by the guarantee shall only be repaired once payment

has been effected by the client. In the event that the guarantee rights do not

apply, OPTIMUS S.A. shall duly inform the client. If, within a period of 6 weeks

from this communication, no written repair order is received from the client

confirming acceptance of the costs, OPTIMUS S.A. shall return the unit in

question to the client. In this case, the transport and packaging costs shall be

invoiced separately and payment shall be made on delivery. In the event that a

repair order is sent by the client, confirming that he assumes the costs of repair,

the transport and packaging costs shall be invoiced additionally, and also

separately.

10. If the equipment needs to be transferred to the Authorised Service Centre,

transportation shall be effected by the responsible party according to the

guarantee, who will also bear the freight and insurance costs.

11. In the event of a defect, OPTIMUS S.A. guarantees that the repair and/or

replacement of parts so that the unit operates correctly will be made within a

period of no more than 30 days. Nevertheless, OPTIMUS S.A. would like to clarify

that the normal period does not exceed 30 days.

12. All parts or products replaced as part of the guarantee services shall

become the property of OPTIMUS S.A.

3. TRANSFER OF GUARANTEE

The guarantee is solely awarded to the original purchaser (principal client) and is

not transferable. With the exception of OPTIMUS S.A., no third party (dealers,

etc.) is authorised to award additional guarantees on behalf of OPTIMUS S.A.

4. CLAIMS FOR DAMAGE

In the event that OPTIMUS S.A. cannot provide a suitable guarantee service, the

purchaser shall not be entitled to claim any indemnity for damages arising. The

responsibility held by OPTIMUS S.A. is limited in all cases to the invoicing price of

the product.

5. RELATION WITH OTHER GUARANTEE RIGHTS AND NATIONAL LAW

1. This guarantee does not affect the rights of the purchaser with respect to the

vendor arising from the contract of sale accomplished.

2. These conditions of the guarantee provided by OPTIMUS S.A. are valid as long

as they do not contradict the corresponding national law on guarantee

provisions.

3. OPTIMUS S.A. guarantees that this product complies with the safety

regulations in force in the country.

THIS LIMITED GUARANTEE DECLARATION IS THE EXCLUSIVE GUARANTEE

OFFERED BY OPTIMUS S.A. ALL OTHER EXPLICIT OR IMPLICIT GUARANTEES ARE

EXCLUDED, AND THIS ALSO APPLIES TO GUARANTEES OF MARKETABILITY AND

SUITABILITY FOR A PARTICULAR PURPOSE. (EXCEPT WHEN THESE GUARANTEES

ARE REQUIRED BY AN APPLICABLE LAW). NO GUARANTEE, EITHER EXPLICIT OR

IMPLICIT, SHALL BE APPLIED ONCE THE GUARANTEE PERIOD HAS EXPIRED.

OPTIMUS S.A.

After Sales Service

C/ Barcelona 101

17003 - GIRONA

Tel. 902 151 96 / 972 203 300

Fax. 972 21 84 13

e-mail:[email protected] 1999/44/CE

9I327 17/03/2017 V3.1.000

Optimus ME-200C User manual

Brand: Optimus

Model: ME-200C

Category: Musical Equipment

Type: User manual

Optimus ME-200C is a microphone desk and voice alarm fireman's panel with CAN Bus communications for COMPACT Systems. Here's an overview of its features and use cases:

Download PDF

report

Optimus ME-200C User manual

Optimus ME-200C User manual

Related papers

Other documents