Fidelio AW2000/10 User manual

Type
User manual
www.philips.com/support
User manual
Always there to help you
Register your product and get support at
AW2000
Question?
Contact
Philips
1
English
EN
Contents
1 Important 2
Safety 2
Notice 3
2 Your Wireless Hi-Fi Receiver 4
Introduction 4
What's in the box 4
What else you need 4
Overview of the main unit 5
3 Prepare 6
Download Philips AirStudio+ Lite to
your smartphone or tablets 6
Connect to an existing speaker system 7
Connect power and switch on 7
4 Connect AW2000 to your home
Wi-Fi network 9
Option 1: Set up wireless connection
to a non-WPS router through an
iOS device 9
Option 2: Set up through a non-WPS
Wi-Fi router and Android device 12
Option 3: Set up wireless connection
to `a WPS router 14
Option 4: Set up wired connection
through an Ethernet cable 15
5 Play 16
Listen to Internet radio stations
through AW2000 16
Play from an external device 18
6 Upgradermware 20
7 Product information 21
Specications 21
8 Troubleshooting 22
9 Appendix: Understand meanings
of LED colors 24
2 EN
1 Important
Safety
Information for Europe:
Know these safety symbols
The 'exclamation mark' calls attention to
features for which you should carefully read the
supplied literature to prevent operating and
maintenance problems.
The 'lightening bolt' symbol indicates
uninsulated components within the product
that can cause an electric shock.
Toreducetheriskofreorelectricshock,do
not expose the product to rain or moisture and
donotplaceanyobjectslledwithliquids,such
asvases,ontheproduct.
a Read these instructions.
b Keep these instructions.
c Heed all warnings.
d Follow all instructions.
e Do not use this product near water.
f Clean only with dry cloth.
g Do not block any ventilation openings.
Install in accordance with the
manufacturer's instructions.
h Do not remove the casing of this product.
i Do not expose the product to dripping /
splashing water, rain or high humidity.
j Keep this product away from direct
sunlight,nakedamesorheat.
k Do not install near any heat sources
such as radiators, heat registers, stoves,
or other electrical equipment (including
ampliers).
l Do not place any other electrical
equipment on the product.
m Do not place any sources of danger
on the product (e.g. objects containing
liquids,burningcandles).
n Where the mains plug or an appliance
coupler is used as the disconnect device,
the disconnect device shall remain readily
operable.
Warning
Never remove the casing of this apparatus.
Never lubricate any part of this apparatus.
Never place this apparatus on other electrical
equipment.
Keepthisapparatusawayfromdirectsunlight,naked
amesorheat.
Ensure that you always have easy access to the power
cord,plugoradaptortodisconnectthisapparatusfrom
the power.
Risk of overheating! Never install this apparatus
inaconnedspace.Alwaysleaveaspaceof
at least four inches around this apparatus for
ventilation. Ensure curtains or other objects
never cover the ventilation slots on this
apparatus.
3
English
EN
Notice
Hereby,GibsonInnovationsdeclaresthatthisproduct
isincompliancewiththeessentialrequirementsand
other relevant provisions of Directive 1999/5/EC.
YoucanndtheDeclarationofConformityonwww.
philips.com/support.
Anychangesormodicationsmadetothisdevicethat
arenotexpresslyapprovedbyGibsonInnovations
may void the user’s authority to operate the
equipment.
Philips and the Philips’ Shield Emblem are registered
trademarks of Koninklijke Philips N.V. and are used
byGibsonInnovationsLimitedunderlicensefrom
Koninklijke Philips N.V.
Specicationsaresubjecttochangewithoutnotice.
Gibsonreservestherighttochangeproductsatany
time without being obliged to adjust earlier supplies
accordingly.
Your product is designed and manufactured
withhighqualitymaterialsandcomponents,
which can be recycled and reused.
When this crossed-out wheeled bin symbol is
attached to a product it means that the product
is covered by the European Directive 2002/96/
EC.
Please inform yourself about the local separate
collection system for electrical and electronic
products.
Please act according to your local rules and
do not dispose of your old products with your
normal household waste. Correct disposal of
your old product helps to prevent potential
negativeconsequencesfortheenvironmentand
human health.
Environmental information
All unnecessary packaging has been omitted.
We have tried to make the packaging easy to
separateintothreematerials:cardboard(box),
polystyrene foam (buffer) and polyethylene
(bags,protectivefoamsheet.)
Your system consists of materials which can
be recycled and reused if disassembled by
a specialized company. Please observe the
local regulations regarding the disposal of
packagingmaterials,exhaustedbatteriesandold
equipment.
AndroidisatrademarkofGoogleInc.Useof
thistrademarkissubjecttoGooglepermissions.
Class II equipment symbol:
CLASSIIapparatuswithdoubleinsulation,and
no protective earth provided.
Note
The type plate is located on the bottom of the
apparatus.
4 EN
2 Your Wireless
Hi-Fi Receiver
Congratulationsonyourpurchase,and
welcometoPhilips!Tofullybenetfromthe
supportthatPhilipsoffers,registeryourproduct
at www.philips.com/welcome.
IfyoucontactPhilips,youwillbeaskedforthe
model and serial number of this apparatus. The
model number and serial number are on the
bottom of the apparatus. Write the numbers
here:
Model No. __________________________
Serial No. ___________________________
Introduction
With this wireless Hi-Fi receiver connected to
anexistingspeakersystem,youcan:
Listen to music sent from a DLNA /
UPnP compatible APP.
listen to Internet radio stations or
online music services.
play music from other audio devices
through the AUXIN(L/R),MP3-LINK,
COAXIAL or OPTICAL socket.
What's in the box
Check and identify the contents of your
package:
Wireless Hi-Fi receiver with built-in
Wi-Fi
2 x AC power cords
Quick start guide
Safety sheet
What else you need
Note
Toenjoymusic,connectAW2000toanexisting
speaker system through the SPEAKER CONNECTOR
L/R(+/-) sockets.
Tohavebettersoundeffect,youcanalsoconnecta
subwoofer to the SUBWOOFER socket on the back
of AW2000.
TostreamaudiowirelesslytoAW2000,you
need:
acertiedWi-Firouter
aniOSorAndroiddevice,suchasan
iPod touch/iPhone/iPad; or an Android
phone or tablet
the Philips AirStudio+ Lite app
available on Apple App Store (for iOS
devices)orGooglePlay Store (for
Android devices)
Connect AW2000 to the same local network
as your iOS/Android device through the Wi-Fi
router.
5
English
EN
Overview of the main unit
a
Switch the device on or to normal/Eco
standby mode.
b Power/status indicator
Show the current status of the device.
c Source indicators
Light up when the corresponding
source is selected.
d Volume knob
Adjust volume.
e SOURCE button
Press repeatedly to select an audio source.
f Numerickeys(1to5)
Select an Internet radio station.
g AC IN ~ socket
Connect the power cord.
h SPEAKERCONNECTORL/R(+/-)
sockets
Connect AW2000 to an existing
speaker system.
i
Headphone socket.
j AUX IN L/R sockets
Connect an external audio device
through RCA audio cables (red/white;
not supplied).
f
qpon
gh i lmjk
e
d
a
c
b
a
c
b
k OPTICAL socket
Connect an external audio device to
AW2000 through an optical cable (not
supplied).
l ETHERNET socket
(Optional) Connect to a wireless
router through an Ethernet cable (not
supplied).
m WI-FI SETUP button
Connect the device to a Wi-Fi
network.
n ANTENNA socket
Connect the supplied Wi-Fi antenna.
o COAXIAL
Connect an external audio device to
AW2000 through a coaxial cable (not
supplied).
p MP3-LINK
Connect an external audio device to
AW2000 through a 3.5mm audio cable
(not supplied).
q SUBWOOFER socket
Connect a subwoofer for better sound
effect.
6 EN
3 Prepare
Always follow the instructions in this chapter
in sequence.
Download Philips AirStudio+
Lite to your smartphone or
tablets
1
(For iPod touch/iPhone/iPad users) Install
Philips AirStudio+ Lite from Apple App
Store,andthenruntheapp.
(For users of Android smartphones or tablets)
Install Philips AirStudio+ Lite fromGooglePlay
Store and then run the app.
2 Flick right to view the introduction pages
and then go to the initial Setuppage,or
tap Skip intro to enter the initial Setup
page directly.
7
English
EN
3 On the initial Setuppage,tapSetup a new
speaker.
4 Readthegeneralsetupsteps,thentap
Next.
Connect to an existing
speaker system
1 Unscrew the speaker connectors.
2 Insert fully the end of a speaker cable with
red mark into the left red (+) connector.
3 Screw the left red (+) connector to secure
the cable.
4 Insert fully the end of a speaker cable
without red mark into the left black (-)
connector.
5 Screw the left black (-) connector to
secure the cable.
6 Repeat steps 2-5 to insert the other
speaker cable into the right connectors.
Connect power and switch
on
Caution
Risk of product damage! Make sure that the power
supply voltage matches the voltage printed on the
bottom of the device.
Riskofelectricshock!WhenyouunplugtheACcord,
always pull the plug from the socket. Never pull the
cord.
BeforeyouconnecttheACcord,makesurethatyou
have completed all the other connections.
8 EN
1 Read the power connection instructions
on the app.
2 Connect the AC power cord to
the AC IN ~ socket on the back of the
device.
the wall power socket.
» The device switches on automatically.
» The power/status indicator blinks
amber during boot-up.
» Afterawhile,forrst-timesetup,the
power/status indicator turns solid
amber.
AC IN ~
3 Tap Next on the app screen to continue.
Switch between normal and Eco power
standby mode
To switch the device to normal standby
mode,brieypress
.
» The power/status indicator turns green.
To switch the device to Eco power standby
mode,pressandhold
for less than 3
seconds and then release the button.
» The power/status indicator turns
amber for a short while and then turns
off.
To switch the device on from normal or
Ecopowerstandbymode,brieypress
again.
Operation LED status
On -> Nor-
mal standby
Brieypress
. Amber/white
->Green
On/Normal
standby ->
Eco power
standby
Press and hold
for less than 3
seconds and then
release the button.
Amber/white
or green ->
Off
Normal
standby/
Eco power
standby ->
On
Brieypress
. Green/Off->
Amber/white
9
English
EN
4 Connect
AW2000 to
your home Wi-
Fi network
To connect AW2000 to your existing home Wi-
Finetwork,youneedtoapplyyourhomeWi-Fi
settings to AW2000.
Choose your best setup method based on the
preconditions listed below.
Platform
of your
mobile
device
Type
of your
Wi-Fi
router
Other
require-
ment
Setup method
iOS Non-WPS No Choose option
1 (see 'Option 1:
Set up wireless
connection to a
non-WPS router
through an iOS
device' on page
9).
Android Non-WPS No Choose option
2 (see 'Option 2:
Set up through
a non-WPS
Wi-Fi router and
Android device'
on page 11).
Either
iOS or
Android
WPS No Choose option
3 (see 'Option 3:
Set up wireless
connection to a
WPS router' on
page 14).
Either
iOS or
Android
Either
non-
WPS or
WPS
You
have an
Eth-
ernet
cable.
Choose option 4
(see 'Option 4: Set
up wired connec
-
tion through an
Ethernet cable' on
page 15).
Before connection of AW2000 to your home
Wi-Finetwork,makesurethat:
a your Wi-Fi router is powered on and
working properly.
b AW2000 has been powered on and
booted up successfully (see 'Connect
powerandswitchon'onpage7).
c you have jotted down your Wi-Fi
password.
Onceconnectedsuccessfully,AW2000will
remember your home Wi-Fi settings. Then you
can play music or listen to Internet radio via
Philips AirStudio+ Lite whenever AW2000 is
powered on and connected to your home Wi-
Fi network automatically.
Option 1: Set up wireless
connection to a non-WPS
router through an iOS device
1
Beforesetup,makesurethatyouriOS
device is connected to your home Wi-Fi
network.
2 Select Standard SETUP and tap Next.
10 EN
3 Read the Wi-Fi setup instructions on the
app.
4 Asinstructed,brieypressWI-FI SETUP
on the back of AW2000.
» The power/status indicator starts to
blink amber and white alternately.
» A new Wi-Fi network created by
AW2000willappear,withthenetwork
name (SSID) of Philips_Install.
< 30S
< 3S
5 Tap Nextontheaboveappscreen,and
then read how to proceed with network
setup.
6 Asinstructed,exittheapp,andthenselect
Philips_Install from the list of available
Wi-Fi networks.
11
English
EN
7 Make sure that your iOS device is
connected to Philips_Install,andthengo
back to Philips AirStudio+ Lite.
8 Wait until the password input box appears.
9 Enter the password of your home Wi-Fi
network,tapDonetonishinput,andthen
tap Next.
* If your Wi-Fi password contains such special
characters as #/:/;/', you need to change your
password.
10 Name your wireless Hi-Fi receiver as you
like,andthentapOK to connect AW2000
to your home Wi-Fi network.
11 Wait until the power/status indicator on
AW2000 turns solid white.
» The following app screen appears.
» AW2000 is connected to your home
Wi-Fi network successfully.
12 EN
Tip
Aftersuccessfulnetworksetup,youcantapRock n'
Roll on the above app screen to get ready for music
playdirectly.Formoredetails,gotothe'Play'section
(see 'Play' on page 16).
Option 2: Set up through a
non-WPS Wi-Fi router and
Android device
1
Beforesetup,makesurethatyourAndroid
device is connected to your home Wi-Fi
network.
2 Select Standard SETUP and tap Next.
3 Read the Wi-Fi setup instructions on the
app.
4 Asinstructed,brieypressWI-FI SETUP
on the back of AW2000.
» The power/status indicator starts to
blink amber and white alternately.
» A new Wi-Fi network created by
AW2000willappear,withthenetwork
name (SSID) of Philips_Install.
< 30S
< 3S
13
English
EN
5 Tap Next on the above app screen.
» Your Android device starts to connect
with the new Wi-Fi network created
by AW2000 automatically.
6 Wait until the wireless Hi-Fi receiver is
found.
7 Enter the password of your home Wi-Fi
network,andthentapNext.
* If your Wi-Fi password contains such special
characters as #/:/;/', you need to change your
password.
8 Name your wireless Hi-Fi receiver as you
like,andthentapOK to connect AW2000
to your home Wi-Fi network.
14 EN
9 Wait until the power/status indicator on
AW2000 turns solid white.
» AW2000 is connected to your home
Wi-Fi network successfully.
Note
Aftersuccessfulnetworksetup,youcantapRock n'
Roll on the above app screen to get ready for music
playdirectly.Formoredetails,gotothe'Play'section
(see 'Play' on page 16).
Option 3: Set up wireless
connection to `a WPS router
1
Select Wi-Fi PROTECTED SETUP and tap
Next.
2 Read the WPS setup instructions.
3 Asinstructed,pressandholdWI-FI SETUP
on the back of AW2000.
» The power/status indicator blinks
amber and green alternately.
> 4S
15
English
EN
4 Press the WPS button on your home Wi-Fi
router.
5 Wait until the power/status indicator on
AW2000turnssolidwhite,thentapNext
on the app screen..
» The following app screen appears.
» AW2000 is connected to your home
Wi-Fi network successfully.
WPS
Tip
ForsomeWi-Firouters,youmayneedtoholdthe
WPS button for Wi-Fi connection or enable the WPS
PBCfunctionfromtheroutercongurationpages.See
theusermanualsofthespecicroutersfordetails.
Aftersuccessfulnetworksetup,youcantapRock n'
Roll on the above app screen to get ready for music
playdirectly.Formoredetails,gotothe'Play'section
(see 'Play' on page 16).
Option 4: Set up wired
connection through an
Ethernet cable
Note
Ifyouusewiredconnection,youjustneedtoselect
Speaker already setup on the initial Setup page (see
'Download Philips AirStudio+ Lite to your smartphone
or tablets' on page 6).
1 Ifyouhavetriedwirelessconnection,
beforesetupofwiredconnection,you
need to reset the wireless Hi-Fi receiver
(see 'Troubleshooting' on page 26).
2 Connect an Ethernet cable (not supplied) to:
the ETHERNET socket on the back of
the device
one of the Ethernet ports on your
home Wi-Fi router
3 Wait until the power/status indicator turns
solid white.
» AW2000 is connected to your home
Wi-Fi network successfully.
LAN4To Modem12V=1A ResetLAN3 LAN2 LAN1
ETHERNET
ETHERNET
16 EN
5 Play
Note
TostreammusictothespeakerviaDLNAUPnP,use
your favorite app from your smartphone or PC/Mac
that supports DLNA UPnP.
Listen to Internet radio
stations through AW2000
1
Run Philips AirStudio+ Lite on your iOS
or Android smartphone or tablet.
2 Search for an Internet radio station by its
nameorlocation,languageetc.
3 TotunetoanInternetradiostation,select
and tap its name in the result list.
17
English
EN
Preset Internet radio stations
1 Tune to an Internet radio station and tap
.
» A list of preset radio stations appears.
2 Tap a row in the list where you want to
addthepresetstation.Forexample,ifyou
want to assign preset number 2 to this
station,tapthesecondrow.
» Amessagepopsup,inwhichthe
station name and preset number are
shown.
3 Tap OKinthemessageboxtoconrm.
» The station is added into your list of
preset radio stations.
4 Repeat the above procedures to add more
presets.
Tip
Youcannotdeleteapresetradiostationdirectly,but
you can replace it with another radio station. For
example,ifyouwanttodeleteastationatpreset#3,
youcantunetoanotherradiostation,tap
,andthen
tap the 3rd row to replace the previous station.
To tune to a preset radio station
Press numerickeys(1-5) on AW2000
directlytotunetotherstvepreset
radio stations.
You can also go to Presets on the app
screen and tap one of your preset stations
to start play.
18 EN
Create your favorite list
1 Tune to an Internet radio station.
2 Tap to add the station into your favorite
list directly.
3 Repeat the above procedures to add more
favorite stations.
To tune to a favorite radio station
GotoFavorite stations on the app screen
and tap one of your favorite stations to
start play.
To delete a favorite radio station
1 Tune to the radio station and tap .
» The radio station if removed from your
favorite list directly.
Play from an external device
You can also listen to an external audio device
through AW2000.
Connect through the MP3-LINK socket:
1 Connect a 3.5mm audio cable (not
supplied) to:
the MP3-LINK socket on the back of
AW2000.
the headphone socket on an external
audio device.
MP3 LINK
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8
  • Page 9 9
  • Page 10 10
  • Page 11 11
  • Page 12 12
  • Page 13 13
  • Page 14 14
  • Page 15 15
  • Page 16 16
  • Page 17 17
  • Page 18 18
  • Page 19 19
  • Page 20 20
  • Page 21 21
  • Page 22 22
  • Page 23 23
  • Page 24 24
  • Page 25 25
  • Page 26 26
  • Page 27 27
  • Page 28 28
  • Page 29 29
  • Page 30 30
  • Page 31 31
  • Page 32 32
  • Page 33 33
  • Page 34 34
  • Page 35 35
  • Page 36 36
  • Page 37 37
  • Page 38 38
  • Page 39 39
  • Page 40 40
  • Page 41 41
  • Page 42 42
  • Page 43 43
  • Page 44 44
  • Page 45 45
  • Page 46 46
  • Page 47 47
  • Page 48 48
  • Page 49 49
  • Page 50 50
  • Page 51 51
  • Page 52 52
  • Page 53 53
  • Page 54 54
  • Page 55 55
  • Page 56 56

Fidelio AW2000/10 User manual

Type
User manual

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI