695159 Instruction Manual
Function Description ( Receiver )
} Automatic and manual receive the radio signal (DCF)
} Max/Min display for indoor / outdoor temperature and humidity
} Time Zone select:-12~+12 Hour differences
} Dual time zone selection
} Continuous calendar up to year 2099
} Calendar display ( Date / Month / weekday )
} Auto adjust to Winter / Summer time ( DST)
} Moon of phase
} ℃/℉ selection
} Indoor temperature trend displays
} Low-battery indication for wireless remote sensor
} Air press trend indication display
} 12HR air pressure history
} 12/24 hour format selectable
} Alarm and Snooze
} Backlight for 5 seconds
} 5 weather icons: sunny/party sunny/cloudy/rainy/storm rain
} 3 comfort icons display ( DRY / COMFORT / WET )
} Weekday display in 7 languages ( English-German-French-Italian-Dutch-Spanish-Danish )
} Outdoor temperature measuring range -50~+70℃
} Indoor temperature measuring range 0~+50℃
} Outdoor / indoor humidity measuring range : 20-95%RH
} Receiver (Clock ) can receive 3 wireless remote sensors ( channel 1/2/3 )
} Battery: DC 1.5V AA size X 3 PCS
Wireless Remoter Sensor ( Transmitter )
} Transmitter frequency :433 MHz
} 3 channels by option
} Range of transmitter is up to 30m
} Battery : DC 1.5V AAA size X 2 PCS
Receiver Unit Appearance:
Front View
Part A-LCD
A1: Max-Min memory A2: Indoor temperature and humidity
A3: Channel A4: Outdoor temperature and humidity
A5: RF icon A6: Transmitter Low battery power display
A7: Alarm icon A8: Dual time ( DCF )
A9: Calendar A10: Radio controlled time
A11: Radio controlled icon A12: 12HR air pressure history
A13 Moon of phase A14: Barometric air pressure
A15: comfort icons A16: Air pressure trend indication
A17: Weather forecast icon
Part B-Buttons
B1: “ DOWN –WAVE ” button B2: “- ( UP / MEM )” button
B3: “ CHANNEL “ button B4: “ SNOOZE / LIGHT ” button
B5: “ALM-SET” button B6: “ SET ” button
B7: “ RESET ” button
Part C-Structure
C1: Insert DC adapter jack C2: Stand
C3: Battery door C4: Wall mount hole
Wireless Remote Sensor Appearance:
Back View
Top View
Part D-LCD
D1: Outdoor temperature / humidity display D2: RF icon
D3: Low battery display D4: Channel
Part E- Buttons
E1: “ Reset “ button E2: “Channel select switch “ button
E3: “℃/℉” button
Part F-Structure
F1: Transmitter Lens F2: Transmitter indication LED
F3: Gases hole F4: Wall mount hole
F5: Battery door F6: Battery compartment
Manual Time Setting :
The setting sequence is shown as follow: Year-Month-Date- Time Zone - 24 HR -Hour-Minute-Weekday Languages
} In time mode, press and hold down the ” SET(B6) ” button for 3 seconds, the year display 2011 starts to flash,
now use ”+(B1) or ”-(B2)” buttons to set the correct year.
} Press” B6” to confirm your setting, the month display starts to flash, Now use “+(B2)” or “–(B1)“ buttons to set
the correct month.
} Press ” B6 ” to confirm your setting, the date display starts to flash, Now use “+(B2)” or “–(B1)“ buttons to set the
correct date.
} Press “B6” to confirm your setting, the “00” display starts to flash. Now use “+(B2)” or “–(B1)“ buttons to set correct
time zone.
} Press “B6” to confirm your setting, the12/24 HR display starts to flash. Now use “+(B2) ”or “–(B1)“ buttons to set
correct time format.
} Press “B6” to confirm your setting, the hour display starts to flash. Now use “+(B2)” or “–(B1)“ buttons to set
correct hour.
} Press “B6” to confirm your setting, the minute display starts to flash. Now use “+(B2)” or “–(B1)“ buttons to set
correct minute.
} Press “B6” to confirm your setting ,the language selection for the weekday displays states to flash, Now use
“+(B2)” or “–(B1)“ buttons to select a language..
} Press “B6” to confirm your setting and to end the setting procedures.
} After 10 seconds without pressing any button the receiver switches automatically from setting mode to Normal
Back View Back View Front View
clock mode.
Setting The Daily Alarms :
} In time mode, press ”ALM SET (B5)” button one time, and the “ ”icon appears, again press and hold down the
“B2” button for 3 seconds until “AL” hour icon starts to flash, now use ”+(B2)” or "-(B1) “ buttons to set your want
time, and press “B5” to confirm your setting, ” AL “ minute display start to flash, press ”+(B2)” or “–(B1)” buttons to
set you want time. And press “B5” to confirm your setting.
} If you want cancel the alarm, please change the alarm mode and press “B5 “ button one time to cancel the alarm,
and the “ ”icon disappears .
To Use Snooze Alarm:
When time reaches your set alarm time ,your clock will give beep sound to wake up, the “ ”icon will flash..
} Press” SNOOZE/LIGHT(B4) ” button once to stop the alarm temporarily, the “ ” icon keeps flashing ,the alarm
will beep again in 5 minutes.
} To stop the alarm , press anything button once ,the alarm beep will stop and the “ ” icon become static ,alarm will
beep again same time next day.
Alarm Duration : 2 minutes.
Snooze Duration: 5 minutes
Reception Of The Radio Signal :
} When you insert the batteries, all the icons on the LCD display will briefly up for 3 seconds, and you will hear a
beep tone.
} The Receiver (clock ) will now start to make a connection to the wireless remote sensor, this operation takes
about 3 minutes and is displayed by flashing reception RF symbol “ “ on the LCD display .
} After receiver has created a connection to the wireless remote sensor ( after 3 minutes ), it will then begin the
automatic reception of the DCF radio signal , this operation takes up to 7 minutes and is display by flashing radio
mast symbol “ ” on the LCD display.
} If reception is successful, then the radio controlled icon ” “ will appear continuously on the LCD display.
} The Receive automatically must scan the DCF signal at 1:00 a.m.2:00 a.m.3:00 a.m .everyday, if it receiver DCF
signal at 3:00 a.m. it will stop receiving until 1:00 a.m. next day .but if it fail reception at 3:00 a.m,it will repeat again
at 4:00 a.m.5:00 a.m. This procedure is repeated automatically up to 5 times.
} If this automatic process is unsuccessful, then use a sharp object to press the “ RESET (B6) “button on the
Receiver.
Remarks :
} A flashing radio mast symbol indicates that the DCF signal reception has started.
} A continuously displayed radio mast symbol indicates that the DCF was received successfully.
} We recommend a minimum distance of 2.5 meters (8.2 Feet) to all sources of interference such as televisions or
computer monitors.
} Radio reception is weaker in rooms with concrete walls (e.g. in cellars) and in offices. In extreme cases, place the
system at a window.
} As there is less atmospheric interference at night, radio reception is normally possible at this time. A single
synchronization each day is sufficient to keep the time display accurate to one second.
Manual Receive Signal :
To start DCF reception manually, press ” WAVE (B1) ” button for 2 seconds, The radio controlled icon “ ” starts to
flash. if reception is successful the radio controlled icon ” “ on the LCD display. If you want to stop DCF
reception , press and hold down “ WAVE (B1) ” for 2 seconds. If no signal is received within seven minutes, then
the DCF signal search stops ( the radio controlled icon “ ” disappears ) and starts again the next full hour .
DCF Signal Reception And Signal Indicator
Weak or no DCF signal ( only icon flashing)
Receiving strong DCF signal ( icon flashing )
Successful Reception ( icon becomes static)
Failed Reception ( icon disappear)
Remark: when your clock is receiving radio controlled time signal ,all buttons except the snooze/light button do not
function.
℃/℉ Temperature Display
The temperature is displayed either in ℃/℃,briefly pressing the “DOWN (B1)“ button allows you to switch between
individual mode.
Moon Phase and Tide Indication
} Moon phase will be displayed automatically according to current calendar. There are 8 different moon
Phases (Moon phase icon：Waning crescent; New moon; Waxing crescent; Waxing gibbous; First quarter; Waning
gibbous; Full moon; Last quarter) ranging from New Moon to full Moon. Moonphase display is controlled by the
current calendar.
WET / COMFORT / DRY Icons
DRY Humidity below 40%
COMFORT Temperature 20-28℃ ( 68-82℉ ) ,humidity in 40-70% range
WET Humidity over 70%
NO Display When temperature isn’t in 20-28℃ range , Humidity in 40-70% range
Weather Forecaster Icon And Pressure Trend Indicator
} The Receiver (Clock ) has a built-in barometric sensor which measures the change of the air pressure over time ,it
takes around 24 hour go gather and average air-pressure reading to provide a weather forecast for next 12-24
hour.
Weather Forecast Icons :
There are four possible types of weather icons that will be displayed
SUNNY PARTLY SUNNY CLOUDY RAIN RAINSTORM
Air Pressure Tendency Indicators
} When the arrow upward appears , the air pressure is increasing , the weather is expected to improve
} When the arrow downward appears , the air pressure is decreasing , the weather is expected to become worse
} When the arrow horizontal appears , the air pressure change is stable
Air Pressure History Bar Chart
} The bar chart indicates the air pressure history trend over the last 12 hours in 6 steps :0h,-1h,-2h,-3h,-6h and -12h
} The “oh” represent the current full hour air pressure recording
} The columns represent the “hPa” at specific time
} If the bars are raising it means that the weather is getting better due to the increase of air pressure
} If the bars go down , it means the air pressure has dropped and the weather is expected to get worse from the
present time “0h”
Remarks :
} Moving your weather from one floor of a building to another floor will affect the accuracy of your Receiver, which
should operate at the same altitude all the time , if you move it to a new location , it will take 12-24 hour to get
stable and accurate again.
} As you go higher in the air , the atmospheric pressure decreases, the exact pressure at a particular altitude
depends of weather conditions , but a couple of approximations and a formula can give you a general idea of how
pressure decreases with altitude, a rule of thumb for the altimeter correction is that the pressure drops about 1
hPa for each 8 meters of altitude gain , these rules work quite well for elevations or altitudes of less than two or
three thousand feet.
} Our Receiver provides next 12-24 hours weather forecast , it may not match with the current weather condition
outside.
TO Read Maximum-Minimum Indoor /Outdoor Temperature And Humidity:
} Press the ” UP/MEM (B2) ” button to show the maximum indoor /outdoor temperature and humidity with “MAX”
icons appearing on the display.
} Press the “ UP/MEM (B2)”button again to show the maximum indoor / outdoor temperature and humidity with
“MIN” icons appearing on the display.
} In “MAX/MIN” mode ,hold ” UP/MEM ( B2) ” button for 3 seconds to clear the recorder max/min reading.
} Press ” DOWM (B1) ” button to select indoor/outdoor temperature in Celsius( ℃ )mode or Fahrenheit ( ℉ )
mode.
Display Outdoor Temperature :
Press “ CHANNEL(B5)” button to show the 3 channel temperature, the sequence is shown as follow:
If only one sensor is registered , press “ CHANNEL (B3) “ button will has no function
} Hold “CHANNEL(B3)” button for 3 seconds to cancel unused channel manually, it will automatically search
and register a new channel again if a new channel is received , if there no temperature display in existing
channel (“--- ---“ is display on the LCD), hold “ CHANNEL (B3)” button for 3 seconds to cancel that channel
and receive the channel again.
Wireless Remote Sensor Registration Procedure :
} The wireless remote sensor will automatically transmit temperature to the receive (clock ) after batteries
inserted .
} For having more than one external transmitter ,select the channel (CH1-CH2-CH3) to ensure each wireless
remote sensor is transmitting different channel before inserting batteries, the channel selecting switch (E2)
button is at the back of the wireless remoter sensor.
} Press “℃/℉ “ (E3) button on the wireless remote sensor , to select displayed in Celsius mode or
Fahrenheit mode
Press
“
CHANNEL
”
(B3
)
Press
“CHANNEL”(B3)
Press
“CHANNEL”(B3)
/
