Amana 2246003 Installation, Operation & Application Manual

  • Hello! I am an AI chatbot trained to assist you with the Amana 2246003 Installation, Operation & Application Manual. I’ve already reviewed the document and can help you find the information you need or explain it in simple terms. Just ask your questions, and providing more details will help me assist you more effectively!
ELECTRICAL SHOCK HAZARD
– Turn off power at the main service panel by removing
the fuse or switching the appropriate circuit breaker to the OFF position before
removing the existing thermostat.
1. Turnoffpowertotheheatingandcoolingsystembyremovingthefuseorswitchingthe
appropriatecircuitbreakeroff.
2. Removecoverofoldthermostat.Thisshouldexposethewires.
3. Labeltheexistingwireswiththeenclosedwirelabelsbeforeremovingwires.
4. Afterlabelingwires,removewiresfromwireterminals.
5. Removeexistingthermostatbasefromwall.
6. Refertothefollowingsectionforinstructionsonhowtoinstallthisthermostat.
To Remove Existing Thermostat
Specifications
Electrical rating: •24VAC(18-30VAC)
•4ampmaximumtotalload
•1ampmaximumperterminal
Temperature control range: 45°Fto90°F(7°Cto32°C)Accuracy:±1°F(±0.5°C)
System congurations:2-stageheat&1-stagecoolheatpump,1-stageelectricheat
Timing:
Anti-shortCycle:
4minutes
BacklightOperation:10seconds
Terminations:R,C,O/B,Y,W,GH,GL
Important Safety Information
WARNING!
:
Always turn off power at the main power supply before installing, cleaning,
or removing thermostat.
•Thisthermostatisfor24VACapplicationsonly;donotuseonvoltagesover30VAC
•Allwiringmustconformtolocalandnationalelectricalandbuildingcodes
•Donotuseairconditioningwhentheoutdoortemperatureisbelow50degrees;thiscandamage
yourA/Csystemandcausepersonalinjuries
•Usethisthermostatonlyasdescribedinthismanual
Package Contents/Tools Required
Package includes: Amana
®
2246003thermostatonbase,thermostatcover,wiringlabels,screws
andwallanchors,Installation,OperationandApplicationGuide
Tools required for installation:Drillwith3/16”bit,hammer,screwdriver
Installation, Operation &
Application Guide
www.amana-ptac.com
2246003
Non-Programmable Electronic Thermostat
Electric Heat or HP, Manual Changeover, Hardwired
Congurable
2-Stage Heat Pump Systems
1-Stage Electric Heat
Backlit Display
Field Calibration Feature
Relay Outputs
(minimum voltage drop in thermostat)
Ideally Suited for:
–Residential(NewConstruction/Replacement)
–LightCommercial
Parts Diagram
RESET
LEFT RIGHT
FanSwitchModeSwitch
Left
Button
Right
Button
ResetSwitch
LargeBacklitDisplay
UpButton
DownButton
ELECTRICAL SHOCK HAZARD
– Turn off power at the main service panel by removing
the fuse or switching the appropriate circuit breaker to the OFF position before
removing the existing thermostat.
IMPORTANT: Thermostatinstallationmustconformtolocalandnationalbuildingand
electricalcodesandordinances.
Note:Mount the thermostat about four feet above the oor. Do not mount the thermostat
on an outside wall, in direct sunlight, behind a door, or in an area affected by a vent
or duct.
1.Turnoffpowertotheheatingandcoolingsystembyremovingthefuseorswitchingtheappropriate
circuitbreakeroff.
2. Toremovecover,insertandtwistacoinorscrewdriverintheslotsontopofthethermostat.
3. Putthermostatbaseagainstthewallwhereyouplantomountit(Besurewireswillfeedthrough
thewireopeninginthebaseofthethermostat).
4. Marktheplacementofthemountingholes.
5. Setthermostatbaseandcoverawayfromworkingarea.
6. Usinga3/16”drillbit,drillholesintheplacesyouhavemarkedformounting.
7. Useahammertotapsuppliedanchorsinmountingholes.
8. Alignthermostatbasewithmountingholesandfeedthecontrolwiresthroughwireopening.
9. Usesuppliedscrewstomountthermostatbasetowall.
10.Insertstripped,labeledwiresinmatchingwireterminals.See“WiringDiagrams”sectionofthis
manual.
CAUTION!
:
Besureexposedportionofwiresdoesnottouchotherwires.
11. Gentlytugwiretobesureofproperconnection.Doublecheckthateachwireisconnectedtothe
properterminal.
12.Sealholeforwiresbehindthermostatwithnon-ammableinsulationorputty.
13.Replacecoveronthermostatbysnappingitinplace.
14.Turnonpowertothesystematthemainservicepanel.
15.Testthermostatoperationasdescribedin“TestingtheThermostat”.
To Install Thermostat
Terminal Designator Descriptions
R – 24VAChot
C – 24VACcommon
O/B – Reversingvalve
Y – 1ststagecool,1ststageHPheatforHP
W – 2ndstageheatforHP,1ststageelectricheat
GH – FanHigh
GL – FanLow
Wiring Diagram Conversions
Cool & Electric Heat Heat Pump
Output Chart
1
ST
Cool 1
ST
Heat 2
ND
Heat
HSo=HeatPump(coolactivereversingvalve)
Y,GL,O Y,GL Y,GL,W
HSb=HeatPump(heatactivereversingvalve)
Y,GL Y,GL,B Y,GL,B,W
HSE=ElectricHeat
Y,GL W,GL W,GL
Note:GL will be on during heating and cooling cycle when fan switch is set to Auto
FanHigh
FanLow
Heat
Compressor
X
Former
ReversingValve
AuxiliaryHeat
Compressor
FanHigh
FanLow
X
Former
ROOMSET
8. Room temperature offset(+9°Fto-9°F)(+4.5°Cto-4.5°C)
Adjusttocalibratedisplayedroomtemperaturetomatchactualroom
temperature.
Note:When not set to 0, ROOM will display.
Pressthedownorupbuttontoselect.
SlideMode switchtoHeatorCooltoexitcongurationmode..
SET
7. Minimum Cool Setpoint(45°Fto90°F)(7.0°Cto32.0°C)
AdjusttocontroltheminimumCoolsettemperatureallowed.
Pressthedownorupbuttontoselect.
PresstheRIGHT buttontoadvancetothenextscreen.
SET
6. Maximum Heat Setpoint(45°Fto90°F)(7.0°Cto32.0°C)
AdjusttocontrolthemaximumHeatsettemperatureallowed.
Pressthedownorupbuttontoselect.
PresstheRIGHT buttontoadvancetothenextscreen.
5. Staged Off Outputs(showsonlyforHP)
Selectwhethertheoutputsforheatingandcoolingarestagedoff
independentlyoraresatisedsimultaneously.
1= EconomyMode–Outputsarestagedonandoffinaccordancewithset
pointanddifferential.
0= ComfortMode–Outputsarestagedonandandallstagescycleoff
simultaneouslywhensetpointissatised.
Pressthedownorupbuttontoselect.
PresstheRIGHT buttontoadvancetothenextscreen.
ROOM
CAUTION!
:
Donotuseairconditioningwhentheoutdoortemperatureisbelow50
degrees.Thiscandamageyourairconditioningsystemandcausepersonal
injuries.
1. MovetheHigh/Auto/LowswitchtotheAutoposition.
2. MovetheCool/Off/Heat switchtoHeatorCool,dependingontheseason.
Starting the Thermostat
3. Temperature Differential – Stage 1 – (1°F to 5°F) (0.5°C to 2.5°C)
Setthenumberofdegreesbetweenyour“setpoint”temperatureandyour“turn
on”temperatureforrststage.
Pressthedownorupbuttontosetdifferentialvalue.
PresstheRIGHT buttontoadvancetothenextscreen.
DIFF
Conguration Mode Settings
ThesetupscreensforCongurationModeareasfollows:
1. Temperature Scale (F or C) –ChooseFahrenheitorCelsius.
Pressthedownorupbuttontoselect.
PresstheRIGHT buttontoadvancetothenextscreen.
DIFF
4. Temperature Differential – Stage 2 – (1°F to 5°F) (0.5°C to 2.5°C)(showsonlyforHP)
Setthenumberofdegreesbetweenwhenstage1turnsonandstage2turnson.
Pressthedownorupbuttontosetdifferentialvalue.
PresstheRIGHT buttontoadvancetothenextscreen.
Configuration Mode
ThecongurationmodeisusedtosettheAmana
®
2246003tomatchyourheating/coolingsystem.
ToconguretheAmana
®
2246003,performthefollowingsteps:
1. SlidetheModeswitchtotheOFFposition.
2. Removethecoverofthethermostatbygentlypullingononeofthecorners.
3. SimultaneouslyholdtheLEFT &RIGHT buttonsinfor2secondswhiletheAmana
®
2246003isin
OFFmode.
4. Pressthedownorupbuttontochangesettingswithineachscreen.
5. PresstheRIGHT buttontoadvancetothenextscreen.
Note:The LEFT button will return you to the previous screen.
6. Toexitcongurationmode,slidetheModeswitchtoHeatorCool.
2. Heating System
HSo – Heatpump,coolactivereversingvalve
HSb – Heatpump,heatactivereversingvalve
HSE – Electricheatsystem
Oncethethermostatisinstalled,itshouldbethoroughlytested.
CAUTION!:
Do not energize the air conditioning system when the outdoor temperature is
below 50 degrees. It can result in equipment damage or personal injury.
Testing the Thermostat
Mode of Operation
TheAmana
®
2246003isathermostatfor24VACsystems.
Heat Pump Operation
Thethermostatactivatestheheatpumpwhentheroomtemperatureisbelowtheheatset
temperature(bythedifferentialtemperature).Auxiliaryheatwillbeactivatediftheroomtemperature
continuestodrop.Theheatoutputsarestagedoff(congurable,setting5)astheroomtemperature
increases.Thethermostatwillnotletthecompressorcomeonforfourminutesafteritturnsoff.This
protectsyourcompressor.
Electric Heat Operation
Thethermostatactivatedtheelectricheatwhentheroomtemperatureisbelowtheheatset
temperature(bythedifferentialtemperature).Theheatisturnedoffwhentheroomtemperatureraises
toonedegreeabovetheheatsetpointtemperature.
Whentheroomtemperatureisgreaterthanthecoolsettemperature(bythedifferentialtemperature),
thecoolingdeviceisactivated.Thethermostatwillnotletthecompressorcomeonforfourminutes
afteritturnsoff.Thisprotectsyourcompressor.
TheAmana
®
2246003hasthefollowingoperatingmodes:
Cool
,
Off
,
Heat
.InOFFmode,the
thermostatwillnotturnonheatingorcoolingdevices.IntheHeatmode,thethermostatcontrolsthe
heatingsystem.IntheCoolmode,thethermostatcontrolsthecoolingsystem.Theindoorfancanbe
turnedoninalloperatingmodesusingtheFanswitch.
• Set fan to HIGH:forcontinuoushighspeedoperation
• Set fan to LOW:forcontinuouslowspeedoperation
• Set fan to AUTO:forlowspeedfanoperationonlyduringaheatorcoolcycle
Troubleshooting
Symptom Remedy
Nodisplay Checkfor24VACatthermostat;displayisblankwhen24VACisnot
present
Systemfandoesnotcomeon
properly
Verifywiringiscorrect
Thermostatturnsonandofftoo
frequently
Adjusttemperaturedifferential(see“TemperatureDifferential,”Stage1,
Step3)
Fanrunscontinuously CheckfanLow/Auto/HIghswitch.LoworHighpositionrunsindoorfan
continuously
Roomtemperatureisnotcorrect Verifywallholeispluggedwithputtyorinsulation;calibratethermostat
(see“Conguration,”Step8)
ROOMdisplays Roomtemperatureoffsetisnotzero(see“Conguration,”Step8)
Auxiliaryheatnotonsoonenough Adjustdifferentialfor2ndstageheatingifrequired(seeConguration,
Steps3&4)
Problemnotlistedabove PresstheResetbuttononce;displaywillberefreshed
CoolOffHeat
Cool Test
1. SlideModeswitchtoCoolmode.
2. Adjustsettemperaturesoitis5degreesbelowroomtemperature.
3. Airconditioningshouldcomeonwithinafewseconds.
4. Adjustthesettemperature2degreesabovetheroomtemperatureandtheA/Cshouldturnoff.
Theremaybeafandelayonyoursystem.
Note:There is a four minute time delay to protect the compressor after it turns off. To
temporarily bypass the four minute delay, slide the Mode switch to OFF for 2 seconds
and then back to Cool.
CoolOffHeat
Heat Test
1. SlideModeswitchtoHeatmode.
2. Adjustthesettemperaturesoitis5degreesabovetheroom
temperature.
3. Heatshouldcomeonwithinafewseconds.
4. Adjustthesettemperaturesoitis2degreesbelowtheroom
temperatureandtheheatshouldturnoff.Theremaybeafandelayonyoursystem.
Note:For Heat pumps, there is a four minute time delay to protect the compressor after it turns
off. To temporarily bypass the four minute delay, slide the Mode switch to OFF for 2
seconds and then back to Heat.
LowAutoHighLowAutoHigh
LowAutoHigh
LowAutoHighLowAutoHigh
Fan Test
1. SlideFanswitchtoHighposition.
2. Indoorfanturnsoninhighspeed.
3. SlideFanswitchtoLowposition.
4. Indoorfanturnsoninlowspeed.
5. SlideFanswitchtoAutoposition.
6. Indoorfanturnsoff.
LIAF173
/