Sharp XG-MB67X Quick start guide

MODEL

XG-MB67X

MULTIMEDIA PROJECTOR

SETUP MANUAL

Connecting Pin Assignments ............................ 2

RS-232C Specifications and Commands .......... 3

Setting up the Projector Network Environment ...

7

1. Connecting the Projector to a Computer............ 8

2. Setting an IP Address for the Computer ............ 9

3. Setting up a Network Connection for the Projector ..

11

Controlling the Projector via LAN .................... 13

Controlling the Projector Using Internet Explorer

(Version 5.0 or later) ................................... 13

Confirming the Projector Status (Status) ............. 14

Controlling the Projector (Control) ....................... 14

Setting and Adjusting the Projector

(Settings & Adjustments)............................ 15

Setting the Security (Network – Security) ............ 15

Making General Settings for the Network

(Network – General) .................................. 16

Setting for Sending E-mail when an Error Occurs

(Mail – Originator Settings) ....................... 16

Setting Error Items and Destination Addresses

to which E-mail is to be Sent when an

Error Occurs (Mail – Recipient Settings) ... 17

Setting Error Items and the URL that are to be

Displayed when an Error Occurs

(Service & Support – Access URL) ........... 17

Setting up the Projector Using RS-232C or Telnet ....

18

When Connecting Using RS-232C....................... 18

When Connecting Using Telnet ............................ 19

SETUP MENU (Main Menu) ................................. 20

ADVANCED SETUP MENU ................................. 20

View Setting Detail List ([V]View All Setting) ....... 21

Set Items ............................................................... 21

Save Settings and Quit ([S]Save & Quit) ............. 22

Quit without Saving Settings ([Q]Quit Unchanged) ..

22

IP Address Setting ([1]IP Address) ...................... 23

Subnet Mask Setting ([2]Subnet Mask) ............... 23

Default Gateway Setting ([3]Default Gateway) .... 23

User Name Setting ([4]User Name) ..................... 23

Password Setting ([5]Password) .......................... 24

RS-232C Baud Rate Setting

([6]RS-232C Baud Rate) ............................ 24

Projector Name Setting ([7]Projector Name) ....... 24

DHCP Client Setting ([8]DHCP Client)................. 24

Disconnecting All Connections

([D]Disconnect All) ..................................... 25

Entering ADVANCED SETUP MENU

([A]Advanced Setup) .................................. 25

Setting Auto Logout Time

(ADVANCED[1]Auto Logout Time) ............. 25

Data Port Setting (ADVANCED[2]Data Port) ....... 25

Carrying out Network Ping Test

(ADVANCED[5]Network Ping Test) ............ 26

Setting of Accept IP Address (ADVANCED[6]Accept

IP Addr(1) – [8]Accept IP Addr(3)) ................ 26

Accepting All IP Addresses

(ADVANCED[9]Accept All IP Addr) ............ 26

Setting of Search Port

(ADVANCED[0]Search Port) ...................... 27

Return to Default Settings

(ADVANCED[!]Restore Default Setting) ............

27

Return to Main Menu

(ADVANCED[Q]Return to Main Menu) ..............

27

Troubleshooting ................................................. 28

-2

RS-232C Terminal: 9-pin mini DIN female connector

Pin No. Signal Name I/O Reference

1 Not connected

2RDReceive Data Input Connected to internal circuit

3SDSend Data Output Connected to internal circuit

4 Not connected

5SGSignal Ground Connected to internal circuit

6 Not connected

7RSRequest to Send Connected to CS in internal circuit

8CSClear to Send Connected to RS in internal circuit

9 Not connected

RS-232C Terminal: 9-pin D-sub male connector of the DIN-D-sub RS-232C adaptor

Pin No. Signal Name I/O Reference

1 Not connected

2RDReceive Data Input Connected to internal circuit

3SDSend Data Output Connected to internal circuit

4 Not connected

5SGSignal Ground Connected to internal circuit

6 Not connected

7RSRequest to Send Connected to CS in internal circuit

8CSClear to Send Connected to RS in internal circuit

9 Not connected

RS-232C Cable recommended connection: 9-pin D-sub female connector

Pin No. Signal Pin No. Signal

1CD 1 CD

2RD 2 RD

3SD 3 SD

4ER 4 ER

5SG 5 SG

6DR 6 DR

7RS 7 RS

8CS 8 CS

9CI 9 CI

Note

• Depending on the controlling device used, it may be necessary to connect Pin 4 and Pin 6 on the controlling

device (e.g. computer).

LAN Terminal : 8-pin RJ-45 modular connector

Pin No. Signal Pin No. Signal

1 TX+ 5

2 TX– 6 RX–

3 RX+ 7

48

8

9

6

5

12

4

3

7

1

6

11

5

15

10

COMPUTER-RGB/COMPONENT INPUT 1, 2 and COMPUTER-RGB/COMPONENT OUTPUT Terminals

:

15-pin mini D-sub female connector

Connecting Pin Assignments

COMPUTER-RGB Input/Output

1. Video input (red)

2. Video input (green/sync on green)

3. Video input (blue)

4. Not connected

5. Not connected

6. Earth (red)

7. Earth (green/sync on green)

8. Earth (blue)

9. Not connected

10. GND

11. Not connected

12. Bi-directional data

13. Horizontal sync signal: TTL level

14. Vertical sync signal: TTL level

15. Data clock

Component Input/Output

1. P

R

(C

R

)

2. Y

3. P

B

(C

B

)

4. Not connected

5. Not connected

6. Earth (P

R

)

7. Earth (Y)

8. Earth (P

B

)

9. Not connected

10. Not connected

11. Not connected

12. Not connected

13. Not connected

14. Not connected

15. Not connected

15

69

51

96

8... 1

Projector

Pin No.

4

5

6

Computer

Pin No.

4

5

6

-3

Computer control

A computer can be used to control the projector by connecting an RS-232C serial control cable (cross type,

commercially available) to the projector. (See page 26 of the projector’s operation manual for connection.)

Communication conditions

Set the serial port settings of the computer to match that of the table.

Signal format: Conforms to RS-232C standard. Parity bit: None

Baud rate*: 9,600 bps / 115,200 bps Stop bit: 1 bit

Data length: 8 bits Flow control: None

*Set the projector’s baud rate to the same rate as used by the computer.

Basic format

Commands from the computer are sent in the following order: command, parameter, and return code. After

the projector processes the command from the computer, it sends a response code to the computer.

Info

• When controlling the projector using RS-232C commands from a computer, wait for at least 30 seconds

after the power has been turned on, and then transmit the commands.

• When more than one code is being sent, send each command only after the response code for the previ-

ous command from the projector is verified.

• “POWR????” “TABN _ _ _ 1” “TLPS _ _ _ 1” “TPOW _ _ _ 1” “TLPN _ _ _ 1” “TLTT _ _ _ 1” “TLTL _ _ _ 1”

“TNAM _ _ _ 1” “MNRD _ _ _ 1” “PJN0 _ _ _ 1”

When the projector receives a command shown above:

* The on-screen display will not disappear.

* The “Auto Power Off” timer will not be reset.

Return code (0DH)

C1 C2 C3 C4 P1 P2 P3 P4

Response code format

Normal response

Problem response (communication error or incorrect command)

O K

E R R

Command 4-digit Parameter 4-digit

Command format

Return code (0DH)

Return code (

0DH)

RS-232C Specifications and Commands

Note

• If an underbar (_) appears in the parameter column, enter a space.

• If an asterisk (*) appears in the parameter column, enter a value in the range indicated in brackets under

Control Contents.

*1 For setting the projector name, send the commands in the order of PJN1, PJN2 and PJN3.

*2 Parameters of CLR Temp settings are as follows.

CLR Temp

5500K

6500K

7500K

Parameter

_0 5 5

_0 6 5

_0 7 5

CLR Temp

8500K

9300K

10500K

Parameter

_0 8 5

_0 9 3

_1 0 5

-4

RS-232C Specifications and Commands

Commands

Example: When turning on the projector, make the following setting.

→

←

POWR _ 1__ OK

ProjectorComputer

Power Off

Power On

Power Status

Projector Condition

Lamp Status

Lamp Power Status

Lamp Quantity

Lamp Usage Time (Hour)

Lamp Life (Percentage)

Model Name Check

Projector Name Setting 1

(First four characters) *1

Projector Name Setting 2

(Middle four characters) *1

Projector Name Setting 3

(Last four characters) *1

Projector Name Check

INPUT 1 (RGB1)

INPUT 2 (RGB2)

INPUT RGB Check

INPUT 3 (Video1)

INPUT 4 (Video2)

INPUT Video Check

INPUT Mode Check

INPUT Check

INPUT 1 Adjustment Reset

INPUT 2 Adjustment Reset

INPUT 3 Adjustment Reset

INPUT 4 Adjustment Reset

All Reset

Volume (0 – 60)

Volume up / down (ⴑ10 – ⴐ10)

Keystone

(ⴑ127 – ⴐ127)

AV Mute Off

AV Mute On

Freeze Off

Freeze On

Auto Sync Start

INPUT 1 Resize : Normal

INPUT 1 Resize : Stretch

INPUT 1 Resize : Border

INPUT 2 Resize : Normal

INPUT 2 Resize : Stretch

INPUT 2 Resize : Border

INPUT 3 Resize : Normal

INPUT 3 Resize : Stretch

INPUT 3 Resize : Border

INPUT 4 Resize : Normal

INPUT 4 Resize : Stretch

INPUT 4 Resize : Border

INPUT 1 Picture Mode : Standard

OK or ERR

OK

1

0 : Normal,

1 : Temp High,

8 : Lamp Life 5% or less,

16 : Lamp Burnt-out,

32 : Lamp Ignition Failure

0 : Off, 1 : On, 2 : Retry, 3 : Waiting, 4 : Lamp Error

1 : On, 2 : Cooling, 3 : Shutting Down

1

0 – 9999 (Integer)

0% – 100% (Integer)

XGMB67X

XG-MB67X

OK or ERR

Projector Name

OK or ERR

1 : RGB1 (INPUT1), 2 : RGB2 (INPUT2), ERR

OK or ERR

1 : Video1 (INPUT3), 2 : Video2 (INPUT4), ERR

1 : RGB, 2 : Video

1 : INPUT1, 2 : INPUT2, 3 : INPUT3, 4 : INPUT4

OK or ERR

OK

OK or ERR

0

0 : Normal,

1 : Temp High,

2 : Fan Error,

4 : Lamp Cover Open,

8 : Lamp Life 5% or less,

16 : Lamp Burnt-out,

32 : Lamp Ignition Failure,

64 : Temp Abnormally High

0 : Off, 4 : Lamp Error

0 : Standby

ERR

P

T

M

P

I

R

V

A

V

K

I

F

A

R

O

A

L

P

L

N

J

R

V

M

C

A

B

A

B

L

O

E

M

R

D

A

B

A

B

A

W

B

P

O

P

T

A

R

N

G

E

O

H

R

L

U

Y

B

E

J

S

P

R

N

S

W

N

T

L

M

D

1

2

3

0

B

D

K

E

A

D

S

K

Z

S

R

V

S

_

?

_

*

_

?

_

?

_

?

_

*

_

?

_

?

_

*

_

?

_

*

_

?

_

?

_

*

_

1

0

1

?

1

*

1

2

?

1

2

?

1

*

0

1

0

1

2

6

1

2

6

1

2

3

1

2

3

0

CONTROL CONTENTS

Power ON

Standby mode

(or 30-second startup time)

COMMAND PARAMETER

RETURN

-5

RS-232C Specifications and Commands

INPUT 1 Picture Mode : Presentation

INPUT 1 Picture Mode : Movie

INPUT 1 Picture Mode : Game

INPUT 1 Picture Mode : sRGB

INPUT 1 Contrast (ⴑ30 – ⴐ30)

INPUT 1 Bright (ⴑ30 – ⴐ30)

INPUT 1 Color (ⴑ30 – ⴐ30)

INPUT 1 Tint (ⴑ30 – ⴐ30)

INPUT 1 Red (ⴑ30 – ⴐ30)

INPUT 1 Blue (ⴑ30 – ⴐ30)

INPUT 1 Sharp (ⴑ30 – ⴐ30)

INPUT 1 CLR Temp *2

INPUT 1 Bright Boost (0 – 2)

INPUT 1 Progressive : 2D

INPUT 1 Progressive : 3D

INPUT 1 Progressive : Film Mode

INPUT 1 Signal Type : Auto

INPUT 1 Signal Type : RGB

INPUT 1 Signal Type : Component

INPUT 2 Picture Mode : Standard

INPUT 2 Picture Mode : Presentation

INPUT 2 Picture Mode : Movie

INPUT 2 Picture Mode : Game

INPUT 2 Picture Mode : sRGB

INPUT 2 Contrast (ⴑ30 – ⴐ30)

INPUT 2 Bright (ⴑ30 – ⴐ30)

INPUT 2 Color (ⴑ30 – ⴐ30)

INPUT 2 Tint (ⴑ30 – ⴐ30)

INPUT 2 Red (ⴑ30 – ⴐ30)

INPUT 2 Blue (ⴑ30 – ⴐ30)

INPUT 2 Sharp (ⴑ30 – ⴐ30)

INPUT 2 CLR Temp *2

INPUT 2 Bright Boost (0 – 2)

INPUT 2 Progressive : 2D

INPUT 2 Progressive : 3D

INPUT 2 Progressive : Film Mode

INPUT 2 Signal Type : Auto

INPUT 2 Signal Type : RGB

INPUT 2 Signal Type : Component

INPUT 3 Picture Mode : Standard

INPUT 3 Picture Mode : Presentation

INPUT 3 Picture Mode : Movie

INPUT 3 Picture Mode : Game

INPUT 3 Contrast (ⴑ30 – ⴐ30)

INPUT 3 Bright (ⴑ30 – ⴐ30)

INPUT 3 Color (ⴑ30 – ⴐ30)

INPUT 3 Tint (ⴑ30 – ⴐ30)

INPUT 3 Sharp (ⴑ30 – ⴐ30)

INPUT 3 CLR Temp *2

INPUT 3 Bright Boost (0 – 2)

INPUT 3 Progressive : 2D

INPUT 3 Progressive : 3D

INPUT 3 Progressive : Film Mode

INPUT 4 Picture Mode : Standard

INPUT 4 Picture Mode : Presentation

INPUT 4 Picture Mode : Movie

INPUT 4 Picture Mode : Game

INPUT 4 Contrast (ⴑ30 – ⴐ30)

INPUT 4 Bright (ⴑ30 – ⴐ30)

INPUT 4 Color (ⴑ30 – ⴐ30)

INPUT 4 Tint (ⴑ30 – ⴐ30)

OK or ERR

ERR

R

I

R

I

V

A

B

A

B

P

B

C

T

R

B

S

C

W

I

S

P

B

C

T

R

B

S

C

W

I

S

P

B

C

T

S

C

W

I

P

B

C

T

S

I

R

O

I

D

E

H

T

E

P

I

S

I

R

O

I

D

E

H

T

E

P

I

S

I

R

O

I

H

T

E

P

S

I

R

O

I

_

*

_

*

_

*

_

*

1

*

_

1

*

_

1

*

_

1

*

1

2

3

4

*

0

1

2

0

1

2

0

1

2

3

4

*

0

1

2

0

1

2

0

1

2

3

*

0

1

2

0

1

2

3

*

CONTROL CONTENTS

Power ON

Standby mode

(or 30-second startup time)

COMMAND PARAMETER

RETURN

-6

RS-232C Specifications and Commands

INPUT 4 Sharp (ⴑ30 – ⴐ30)

INPUT 4 CLR Temp *2

INPUT 4 Bright Boost (0 – 2)

INPUT 4 Progressive : 2D

INPUT 4 Progressive : 3D

INPUT 4 Progressive : Film Mode

Clock (ⴑ150 – ⴐ150)

Phase (ⴑ30 – ⴐ30)

H-Position (ⴑ150 – ⴐ150)

V-Position (ⴑ60 – ⴐ60)

Fine Sync Adjustment Reset

Auto Sync : Off

Auto Sync : On

Internal Speaker : Off

Internal Speaker : On

Image Shift (ⴑ96 – ⴐ96 )

OSD Display : Off

OSD Display : On

Video System Selection : AUTO

Video System Selection : PAL

Video System Selection : SECAM

Video System Selection : NTSC4.43

Video System Selection : NTSC3.58

Video System Selection : PAL_M

Video System Selection : PAL_N

Video System Selection : PAL-60

Background Selection : Logo

Background Selection : Blue

Background Selection : None

Lamp Setting : Bright

Lamp Setting : EcoⴐQuiet

Auto Search : Off

Auto Search : On

Auto Power Off : Off

Auto Power Off : On

Auto Keystone : Off

Auto Keystone : On

PRJ Mode : Reverse Off

PRJ Mode : Reverse On

PRJ Mode : Invert Off

PRJ Mode : Invert On

Language Selection : ENGLISH

Language Selection : DEUTSCH

Language Selection : ESPAÑOL

Language Selection : NEDERLANDS

Language Selection : FRANÇAIS

Language Selection : ITALIANO

Language Selection : SVENSKA

Language Selection :

Language Selection : PORTUGUÊS

Language Selection :

Setup Guide : Off

Setup Guide : On

System Sound : Off

System Sound : On

RGB Horizontal Frequency Check

RGB Vertical Frequency Check

Fan Mode : Normal

Fan Mode : High

OK or ERR

x10

-1

kHz (***.* or ERR)

Hz (***.* or ERR)

OK or ERR

ERR

V

I

A

L

I

M

I

T

I

A

I

M

S

T

H

B

N

A

S

N

M

E

M

H

N

P

T

M

E

S

F

L

S

C

W

I

C

P

H

V

R

D

P

D

S

B

M

S

O

K

R

I

L

G

N

R

M

H

T

E

P

L

H

P

E

J

K

S

I

Y

G

D

E

W

S

E

N

A

U

D

Q

D

_

*

_

*

_

*

_

*

_

*

_

*

_

*

_

*

_

1

_

*

0

1

2

*

1

0

1

0

1

*

0

1

2

3

4

5

6

7

8

1

3

4

0

1

0

1

0

1

0

1

0

1

0

1

2

3

4

5

6

7

8

9

0

1

0

1

0

1

2

0

1

CONTROL CONTENTS

Power ON

Standby mode

(or 30-second startup time)

COMMAND PARAMETER

RETURN

PJLink

TM

Compliant:

This product conforms with the PJLink standard Class 1 and all Class 1 commands are implemented.

This product confirms with the PJLink standard specification version 1.00.

-7

Page 8

1. Connecting the projector to a computer

Setting up the Projector Network Environment

This section describes the basic procedure for using the projector via the network.

If the network is already constructed, the projector’s network settings may need to be changed. Please

consult your network administrator for assistance with these settings.

You can make network settings both on the projector and on the computer. The following procedure is for

making settings on the computer.

Network settings on the computer

Connect a LAN cable (Category 5, cross-over type) between the computer and projector.

Pages 9, 10

2. Setting an IP address for the computer

Adjust the IP settings of the computer to enable one-to-one communications with the projector.

Page 11

3. Setting up a network connection for the projector

Adjust the projector network settings to conform to your network.

LAN cable

(commercially available)

Use Internet Explorer

(version 5.0 or later)

to make various

projector settings.

Temporarily change

the computer’s IP

address.

• Microsoft

®

and Windows

®

are registered trademarks of Microsoft Corporation in the United States and/or

other countries.

• All other company or product names are trademarks or registered trademarks of their respective compa-

nies.

-8

Setting up the Projector Network Environment

1. Connecting the Pro-

jector to a Computer

Establishing a one-to-one connection from the

projector to a computer. Using a LAN cable

(Category 5, cross-over type) you can config-

ure the projector via the computer.

1 Disconnect the computer’s LAN

cable from the existing network.

2 Connect a LAN cable (a UTP

cable, Category 5, cross-over

type) to the projector’s LAN ter-

minal and connect the other end

of the cable to the computer’s

LAN terminal.

3 Plug the power cord into the AC

socket of the projector.

4 Turn on the computer.

Info

Confirm that the LINK LED on the rear of the

projector illuminates. If the LINK LED does not

illuminate, check the following :

• The LAN cable is properly connected.

• The power switches of both the projector

and the computer are on.

LAN cable

(cross-over type, commercially available)

ON

A LAN cable being

connected to the network

This completes the connection. Now proceed to “2. Setting an IP Address for the

Computer”.

-9

Setting up the Projector Network Environment

2. Setting an IP Address

for the Computer

The following describes how to make settings

in Windows

®

XP (Professional or Home

Edition).

1 Log on the network using the

administrator’s account for the

computer.

2 Click “Start”, and click “Control

Panel”.

3 Click “Network and Internet Con-

nections”, and click “Network

Connections” in the new win-

dow.

• This manual uses examples to explain

the operations in Category View. If you

are using Classic View, double-click

“Network Connections”.

4 Right-click “Local Area Connec-

tion” and select “Properties”

from the menu.

1

2

1

2

1

2

-10

Setting up the Projector Network Environment

1

2

After confirming or setting, proceed to “3. Setting up Network Connection for the

Projector”.

5 Click “Internet Protocol (TCP/IP)”,

and click the “Properties” button.

6 Confirm or change an IP address

for the setup computer.

1 Confirm and note the current IP ad-

dress, Subnet mask and Default

gateway.

Make sure to note the current IP

address, Subnet mask and Default

gateway as you will be required to re-

set them later.

2 Set temporarily as follows :

IP address : 192.168.150.3

Subnet mask : 255.255.255.0

Default gateway : (Do not input any

values.)

Note

• When “DHCP Client” is set to “OFF” on the

projector:

IP address : 192.168.150.2

Subnet mask : 255.255.255.0

Default gateway : 0.0.0.0

7 After setting, click the “OK” but-

ton, and then restart the com-

puter.

-11

Setting up the Projector Network Environment

3. Setting up a Network

Connection for the

Projector

Settings for such items as the projector’s IP

address and subnet mask are compatible with

the existing network.

Set each item on the projector as follows. (See

page 50 of the projector’s operation manual

for setting.)

DHCP Client : Off

IP Address : 192.168.150.002

Subnet Mask : 255.255.255.000

1 Start Internet Explorer (version

5.0 or later) on the computer, and

enter “http://192.168.150.2/” in

“Address”, and then press the

“Enter” key.

2 If a user name and a password

have not yet been set, just click

the “OK” button.

• If a user name and a password have

been set, input the user name and the

password, and click the “OK” button.

• If the user name or password is entered

incorrectly three times, an error mes-

sage will be displayed.

3 When the screen as shown on

the right appears, click “TCP/IP”.

-12

4 The TCP/IP setting screen ap-

pears, ready for network settings

for the projector.

Note

• Confirm the existing network’s segment (IP

address group) to avoid setting an IP ad-

dress that duplicates the IP addresses of

other network equipment or computers. If

“192.168.150.2” is not used in the network

having an IP address of “192.168.150.XXX”,

you don’t have to change the projector IP

address.

• For details about each setting, consult your

network administrator.

5 Click the “Apply” button.

6 The set values appear. Confirm

that the values are set properly,

and then click the “Confirm” but-

ton.

Setting up the Projector Network Environment

• Close the browser.

• This completes the network settings.

• After setting items, wait for 10 seconds and then re-access.

• Change the IP address of the setting computer back to its original address, which you have noted down in

Step 6-1 on page 10, and then connect the computer and the projector to the network.

Setting example / Remarks

You can set the password to

protect the TCP/IP setting.

Select “ON” or “OFF” to determine

whether to use DHCP

Client

.

You can set this item when “DHCP

Client

” is set to “OFF”.

Factory default setting: 192.168.150.2

Enter an IP address appropriate

for the network.

You can set this item when “DHCP

Client

” is set to “OFF”.

Factory default setting: 255.255.255.0

Set the subnet mask to the same

as that of the computer and

equipment on the network.

You can set this item when “DHCP

Client

” is set to “OFF”.

Factory default setting: 0.0.0.0

* When not in use, set to “0.0.0.0”.

Factory default setting: 0.0.0.0

* When not in use, set to “0.0.0.0”.

Items

New

Password

DHCP

Client

IP Address

Subnet

Mask

Default

Gateway

DNS

Server

-13

Controlling the Projector via LAN

Controlling the Projector

Using Internet Explorer

(Version 5.0 or later)

Complete connections to external equipment

before starting the operation. (See pages 21-

27 of the projector’s operation manual.)

Complete the AC cord connection. (See page

27 of the projector’s operation manual.)

Note

•

When connecting the projector to the LAN, use

a LAN cable (Category 5). When connecting the

projector to a hub, use a straight-through cable.

1 Start Internet Explorer (version 5.0

or later) on the computer.

2 Enter “http://” followed by the

projector IP address set by the

procedure on page 12 followed

by “/” in “Address”, and then

press the “Enter” key.

•

When “DHCP Client” is set to “OFF” on

the projector, IP address is

192.168.150.2. If you did not change the

IP address in “3. Setting up a Network

Connection for the Projector” (pages

11-12), enter “http://192.168.150.2/”.

3 A screen for controlling the pro-

jector appears, ready for per-

forming various status condi-

tions, control, and settings.

After connecting the projector to your network, enter the projector IP address in “Address”

on Internet Explorer (version 5.0 or later) using a computer on the network to start a setup

screen that will enable control of the projector via the network.

-14

Confirming the Projector

Status (Status)

On this screen, you can confirm the projector

status. You can confirm the following items :

••

• MAC Address

••

• Power

••

• Condition

••

• Lamp Timer

••

• Lamp Life

••

• Input

••

• Signal Info

••

• Serial Number

Note

• If you click the “Refresh” button before the

screen is displayed completely, an error

message (“Server Busy Error”) will be dis-

played. Wait for a moment and then oper-

ate again.

• For details about each item, refer to the

projector’s operation manual.

Controlling the Projector via LAN

Controlling the Projector

(Control)

On this screen, you can perform projector

control. You can control the following items :

••

• Power

••

• Input Select

••

• Volume

••

• AV Mute [OFF] [ON]

Note

• If you click the “Refresh” button before the

screen is displayed completely, an error mes-

sage (“Server Busy Error”) will be displayed.

Wait for a moment and then operate again.

• You cannot operate this page while the pro-

jector is warming up.

• While the projector is in standby mode, you

can only control “Power ON”.

• For details about each item, refer to the

projector’s operation manual.

-15

Controlling the Projector via LAN

Setting and Adjusting the

Projector

(Settings & Adjustments)

Example: “Picture” screen display for INPUT 1

On these screens, you can make projector

settings or adjustments. You can set or adjust

the following items :

••

• Picture Mode

••

• CLR Temp

••

• Bright Boost

••

• Progressive (INPUT 3/4)

••

• Lamp Setting

••

• Resolution Setting

••

• Signal Type (INPUT 1/2)

••

• Video System (INPUT 3/4)

••

• Resize

••

• Auto Keystone [OFF][ON]

••

• OSD Display [OFF][ON]

••

• Background

••

• Setup Guide [OFF][ON]

••

• Projection Mode

••

• OSD Language

••

• Auto Search [OFF][ON]

••

• Auto Sync [OFF][ON]

••

• Auto Power Off [OFF][ON]

••

• System Sound [OFF][ON]

••

• Internal Speaker [OFF][ON]

••

• RS-232C Speed

••

• Fan Mode [Normal] [High]

••

• All Reset

Note

• If you click the “Refresh” button before the

screen is displayed completely, an error mes-

sage (“Server Busy Error”) will be displayed.

Wait for a moment and then operate again.

• You cannot operate this page while the pro-

jector is warming up.

• For details about each item, refer to the

projector’s operation manual.

Setting the Security

(Network – Security)

On this screen, you can make settings relat-

ing to security.

Note

• User Name and Password can be up to 8

characters.

• You can input the characters below :

a-z, A-Z, 0-9, -, _

Description

Setting of user name for

security protection.

Setting of password for

security protection.

It is possible to set up to three

IP addresses allowing connec-

tion to the projector.

No limits are set to IP addresses

connecting to the projector.

For security improvement, only an

IP address set by “Address 1-3”

can be connected to the projector.

Items

User Name

Password

Accept IP

Address

All IP

Addresses

From only

specific IP

addresses

-16

Controlling the Projector via LAN

Making General Settings

for the Network (Network -

General)

On this screen, you can make general settings

relating to the network.

After clicking the “Apply” button, the set val-

ues appear. Confirm that the values are set

properly, and then click the “Confirm” but-

ton.

Note

• After setting items, wait for 10 seconds and

then re-access.

• Projector Name can be up to 12 characters.

• You can input the characters below :

A-Z, 0-9, -, _, (,), space

(When “a-z” are input, they are converted to

“A-Z” automatically.)

Description

Setting the projector name.

Setting the time interval in

which the projector will be

automatically disconnected

from the network in units of a

minute (from 1 to 65535

minutes). If the set value is

made 0, the Auto Logout

function is disabled.

Setting the TCP port number

used when exchanging data

with the projector (from 1025 to

65535).

Setting the port number used

when searching for the

projector (from 1025 to 65535).

Items

Projector

Name

Auto

Logout

Time

Data Port

Search

Port

Setting example / Remarks

Setting an SMTP server

address for e-mail transmis-

sion.

e.g.1 : 192.168.150.253

e.g.2 : smtp123.sharp.co.jp

* When using a domain name,

make settings for the DNS

server.

Setting the projector’s e-mail

address. The e-mail address set

here becomes Originator E-mail

Address.

Setting the sender’s name.

The name set here appears in

the “Originator Name” column

of the body of the message.

Items

SMTP

Server

Originator

E-mail

Address

Originator

Name

Setting for Sending E-mail

when an Error Occurs

(Mail – Originator Settings)

On this screen, you can make settings for

sending e-mail to report when the projector

has generated an error.

Note

• SMTP Server, Originator E-mail Address and

Originator Name can be up to 64 characters.

•

You can input the characters below:

SMTP Server and Originator E-mail Address :

a-z, A-Z, 0-9, !, #, $, %, &, *, +, -, /, =, ?, ^, {,

|, },

~

, _, ’, ., @, `

(You can input “@” only one time for “Origi-

nator E-mail Address”.)

Originator Name : a-z, A-Z, 0-9, -, _, (,), space

•

If the settings of “3. Setting up a Network

Connection for the Projector” on pages 11

and 12 are incorrectly set, e-mail will not be

send.

-17

Controlling the Projector via LAN

Setting Error Items and

Destination Addresses to

which E-mail is to be Sent

when an Error Occurs

(Mail – Recipient Settings)

On this screen, you can input e-mail destina-

tions to which error notification (error items)

e-mails are sent.

Note

• E-mail Address can be up to 64 characters.

• You can input the characters below :

a-z, A-Z, 0-9, !, #, $, %, &, *, +, -, /, =, ?, ^, {, |,

},

~

, _, ’, ., @, `

(You can input “@” only one time.)

• For details about error items, refer to the

projector’s operation manual.

Description

Set addresses to which error

notification e-mail is sent. You

can set up to five addresses.

Error e-mail is sent on the error

items checked in their check

boxes.

Send test e-mail. This allows

you to confirm that the settings

for e-mail transmission are

properly set.

Items

E-mail

Address

Error Mail

(Lamp, Temp,

Fan)

Test

Setting Error Items and

the URL that are to be

Displayed when an Error

Occurs

(Service & Support –

Access URL)

On this screen, you can make settings of the

URL and error items that are to be displayed

when the projector has generated an error.

Example of the display when an error occurs

Description

Set the URL that is to be

displayed when an error

occurs. You can set up to five

addresses.

The URL is displayed when an

error checked in their check

boxes occurs.

The set URL site is test-

displayed. This allows you to

confirm that the URL site is

properly displayed.

Items

Access

URL

Condition

(Always, Lamp,

Temp, Fan)

Test

-18

Setting up the Projector Using RS-232C or Telnet

When Connecting Using

RS-232C

1 Launch general purpose terminal

emulator.

2 Input settings for the RS-232C port

of the terminal emulator as follows.

Baud Rate : 9600 bps*

Data Length : 8 bit

Parity Bit : None

Stop Bit : 1 bit

Flow Control : None

* This is the factory default setting. If the value

of Baud Rate for the projector has been

changed, set Baud Rate here according to

the changed value on the projector.

3 Input “PJS11234” and press the

“Enter” key.

4 “OK” is displayed. Input “PJS25678”

and press the “Enter” key within 10

seconds.

5 “User Name:” is displayed. Input the

user name and press the “Enter”

key.

• If a user name has not yet been set, just

press the “Enter” key.

6 “Password:” is displayed. Input the

password and press the “Enter” key.

• If a password has not yet been set, just press

the “Enter” key.

Connect the projector to a computer using RS-232C or Telnet, and open the SETUP MENU on

the computer to carry out various settings for the projector.

7 Input “setup” and press the “Enter”

key.

• SETUP MENU will be displayed.

Note

• User name and password are not set in the fac-

tory default settings.

• If the user name or password is entered incor-

rectly three times, SETUP MENU will be quit.

▼SETUP MENU

---------------------------------SETUP MENU--------------------------------

[1]IP Address [2]Subnet Mask [3]Default Gateway

[4]User Name [5]Password

[6]RS-232C Baud Rate [7]Projector Name [8]DHCP Client

[A]Advanced Setup [D]Disconnect All

[V]View All Setting [S]Save & Quit [Q]Quit Unchanged

setup>

-19

Setting up the Projector Using RS-232C or Telnet

When Connecting Using

Telnet

1 Click “Start” from the Windows

®

desk-

top and select “Run”.

2 Enter “telnet 192.168.150.2” in the text

box that opens up. (If the IP address

of the projector is 192.168.150.2.)

3 Click the “OK” button.

4 “User Name:” is displayed. Input the

user name and press the “Enter”

key.

• If a user name has not yet been set, just

press the “Enter” key.

5 “Password:” is displayed. Input the

password and press the “Enter” key.

• If a password has not yet been set, just press

the “Enter” key.

6 Input “setup” and press the “Enter”

key.

• SETUP MENU will be displayed.

Note

• If the IP address has been changed, be sure to

enter the new IP address in step 2.

• User name and password are not set in the fac-

tory default settings.

• If the user name or password is entered incor-

rectly three times in steps 4 or 5, SETUP MENU

will be quit.

---------------------------------SETUP MENU--------------------------------

[1]IP Address [2]Subnet Mask [3]Default Gateway

[4]User Name [5]Password

[6]RS-232C Baud Rate [7]Projector Name [8]DHCP Client

[A]Advanced Setup [D]Disconnect All

[V]View All Setting [S]Save & Quit [Q]Quit Unchanged

setup>

▼SETUP MENU

-20

Setting up the Projector Using RS-232C or Telnet

SETUP MENU (Main Menu)

[1]IP Address

IP address settings. (Page 23)

[2]Subnet Mask

Subnet mask settings. (Page 23)

[3]Default Gateway

Default gateway settings. (Page 23)

[4]User Name (Factory default setting : Not Re-

quired)

Setting of user name for security protection. (Page 23)

[5]Password (Factory default setting : Not Required)

Setting of password for security protection. (Page 24)

[6]RS-232C Baud Rate (Factory default setting :

9600 bps)

Baud rate settings for the RS-232C terminals. (Page

24)

[7]Projector Name (Factory default setting : XG-

MB67X)

It is possible to assign a projector name. (Page 24)

[8]DHCP Client

DHCP Client settings. (Page 24)

[A]Advanced Setup

Enters ADVANCED SETUP MENU. (Page 25)

[D]Disconnect All

Disconnect all connections. (Page 25)

[V] View All Setting

Displays all setting values. (Page 21)

Can also be used with ADVANCED SETUP MENU.

[S] Save & Quit

Save set values and quit menu. (Page 22)

[Q]Quit Unchanged

Quit menu without saving setting values. (Page 22)

Note

• When “DHCP Client” is set to “OFF” on the

projector:

IP address : 192.168.150.2

Subnet mask : 255.255.255.0

Default gateway : 0.0.0.0

ADVANCED SETUP MENU

[1]Auto Logout Time (Factory default setting : 5 min-

utes)

Setting of time until automatic disconnection of net-

work connection. (Page 25)

[2]Data Port (Factory default setting : 10002)

Setting the TCP port number used when exchang-

ing data. (Page 25)

[5]Network Ping Test

It is possible to confirm that a network connection

between the projector and a computer etc. is work-

ing normally. (Page 26)

[6]Accept IP Addr(1)

[7]Accept IP Addr(2)

[8]Accept IP Addr(3)

[9]Accept All IP Addr (Factory default setting : Ac-

cept All)

For improved security, it is possible to set up to three

IP addresses allowing connection to the projector.

Set IP addresses can be cancelled using [9] Accept

All IP Addr. (Page 26)

[0] Search Port (Factory default setting : 5006)

Setting the port number used when searching for

the projector. (Page 27)

[!] Restore Default Setting

Restores all setting values that can be set using the

menu to the default state. (Page 27)

[Q]Return to Main Menu

Return to the main SETUP MENU. (Page 27)

▼SETUP MENU ▼ADVANCED SETUP MENU

---------------------------------SETUP MENU--------------------------------

[1]IP Address [2]Subnet Mask [3]Default Gateway

[4]User Name [5]Password

[6]RS-232C Baud Rate [7]Projector Name [8]DHCP Client

[A]Advanced Setup [D]Disconnect All

[V]View All Setting [S]Save & Quit [Q]Quit Unchanged

setup>

******************** ADVANCED SETUP MENU ***********************

[1]Auto Logout Time [2]Data Port

[5]Network Ping Test

[6]Accept IP Addr(1) [7]Accept IP Addr(2) [8]Accept IP Addr(3)

[9]Accept All IP Addr [0]Search Port

[!]Restore Default Setting

[Q]Return to Main Menu

advanced>

Page is loading ...

Sharp XG-MB67X Quick start guide

Sharp XG-MB67X Quick start guide

Related papers

Other documents