Installation Instructions
Discovery
®
Gas Cooktop
Models DYCT304G, DYCT365G
Part No. 108861 Rev. A
Verifying the Package Contents ...................................8
Installing the Cooktop ................................................... 8
Connecting the Gas Line..............................................8
Assembling the Burners ...............................................9
Verifying the Correct Setup ........................................10
Installation Checklist ...................................................11
Replacement Parts List................................................... 12
Wiring Diagrams .............................................................. 14
Table of Contents
Before You Begin...
Important Safety Instructions ......................................1
Important Information About Safety Instructions ..........1
General Safety Precautions .........................................2
Electrical Requirements ...............................................3
Gas Supply Requirements ...........................................3
Installation Specifications ............................................4
Product Dimensions .....................................................4
Cabinet and Countertop Layout ...................................6
All specifications are subject to change without notice. Dacor
assumes no liability for changes to specifications.
Important
Installer: In the interest of safety and to minimize problems, read this Installation Instruction manual completely and
carefully before you begin the installation process.
• Leave this Installation Instructions with the consumer.
• Write the Product Data Label information inside the Use and Care manual for the consumer’s future reference.
Consumer: Keep these Installation Instructions for future reference and for the local electrical inspector’s use.
Note: Dacor
®
is not responsible for service required to correct a faulty installation.
© 2015 Dacor, all rights reserved.
If You Need Help...
If you have questions or problems with installation, contact
your Dacor dealer or the Dacor Customer Service Team. For
repairs to Dacor appliances under warranty call the Dacor
Distinctive Service line. Whenever you call, have the model
and serial number of the appliance ready. The model and
serial number are printed on the product data label.
Dacor Customer Service
Phone: (800) 793-0093 ex. 2813 (U.S.A. and Canada)
Monday — Friday 6:00
a.m. to 5:00 p.m. Pacific Time
Website: www.dacor.com
Dacor Distinctive Service (repairs under warranty only)
Phone: (800) 793-0093, ex. 2822 (U.S.A. and Canada)
Monday — Friday 6:00
a.m. to 5:00 p.m. Pacific Time
Customer Service Information
Product Data Label
The product data label is attached to the chassis, under-
neath the unit.
The label contains:
• the model number and serial number
• the electrical requirement and gas supply
requirements
Model Shown:
DYCT365G
Product data
label
Product Data Label Location
1
Important Information About
Safety Instructions
• The Important Safety Instructions and warnings in
these instructions are not meant to cover all possible
problems and conditions that can occur. Use common
sense and caution when installing, maintaining or oper-
ating this or any other appliance.
• Always contact the Dacor Customer Service Team
about problems and conditions that you don’t under-
stand. See Customer Service Information.
Important Safety Instructions
Safety Symbols, Labels, and Alerts
These danger and warning alerts signal the reader to the
risk of death or serious injury:
DANGER
Immediate hazards that WILL result in severe personal
injury or death.
WARNING
Hazards or unsafe practices that COULD result in severe
personal injury or death.
WARNING
TO REDUCE THE RISK OF INJURY TO PERSONS IN
THE EVENT OF A RANGE TOP GREASE FIRE:
a. SMOTHER FLAMES with a close-fitting lid, cookie
sheet or metal tray, then turn off the burner. BE
CAREFUL TO PREVENT BURNS. If the flames do
not go out immediately, EVACUATE AND CALL THE
FIRE DEPARTMENT.
b. NEVER PICK UP A FLAMING PAN - you may be
burned.
c. DO NOT USE WATER, including wet dish cloths or
towels - a violent steam explosion may result.
d. Use a fire extinguisher ONLY if:
◊ You have a Class ABC extinguisher, and you
already know how to operate it.
◊ The fire is small and contained in the area where
it started.
◊ The fire department is being called.
◊ You can fight the fire with your back to an exit.
DANGER
IMPORTANT: If you smell gas:
• Do not use or light any appliance.
• Do not touch any electrical switch or use any electri-
cal devices, including the telephone, in your building.
• From a neighbor’s phone, immediately call the gas
supplier. Follow the gas supplier’s instructions.
• If you cannot contact the gas supplier, call the fire
department.
DANGER
IMPORTANT: Do not store or use combustible, flammable
or explosive vapors and liquids (such as gasoline) on or
in the vicinity of this or any other appliance. Also keep
items that could explode, such as aerosol cans, away
from the cooktop. Do not store flammable or explosive
materials in adjacent cabinets or areas (including above
and below the cooktop).
WARNING
WARNING: NEVER use this appliance as a space heater
to heat or warm the room. Doing so may result in carbon
monoxide poisoning and overheating of the appliance.
WARNING
WARNING: NEVER cover any slots, holes, or passages
on the cooktop and cooktop chassis. Doing so blocks
air flow through the cooktop and may cause carbon
monoxide poisoning. Aluminum foil linings may also trap
heat, causing a fire hazard. Keep all slots, holes, and
passages clear of grease and grime.
CALIFORNIA PROPOSITION 65 WARNING
The burning of gas cooking fuel generates some
by-products that are on the list of substances which
are known by the State of California to cause cancer or
reproductive harm. California law requires businesses
to warn customers of potential exposure to such
substances. To minimize exposure to these substances,
always operate this unit according to the Use and Care
manual, ensuring you provide good ventilation when
cooking with gas.
READ AND SAVE THESE INSTRUCTIONS
PROLONGED POWER FAILURE
Do not attempt to use this appliance during a continuous
power failure.
2
Important Safety Instructions
• Read the accompanying use and care manual com-
pletely before operating this appliance.
• Keep packaging materials away from children.
Plastic sheets and bags can cause suffocation.
• If you receive a damaged product, immediately con-
tact your dealer or builder. Do not install or use a
damaged appliance.
• This cooktop must be properly installed and ground-
ed by a qualified installer according to these instal-
lation instructions prior to use. The installer should
show the customer the location of the gas shut off
valve and the power cord so that they know where
and how to turn off the gas supply and disconnect
power to the cooktop.
• Do not install, repair or replace any part of the
cooktop unless specifically recommended in the liter-
ature accompanying it. A qualified service technician
should perform all other service.
• Before servicing or installing this cooktop, make sure
that the gas supply is turned OFF at the gas supply
valve and that the power plug is disconnected from
the electrical outlet.
• Disconnect the power plug from the electrical outlet
before cleaning. Clean this appliance only in the
manner specified in the Use and Care Manual.
• Only use the cooktop for cooking tasks expected of
a home appliance as outlined in the literature accom-
panying it. This cooktop is not intended for commer-
cial or laboratory use.
• DO NOT TOUCH THE SURFACES OF THE
COOKTOP DURING OR IMMEDIATELY AFTER
USE.
• Do not operate this appliance if the power cord is
damaged.
• Turn the knobs to the OFF position prior to removing
them from the valve stems.
• Clean the cooktop thoroughly before operating it for
the first time. Make sure that all the cooktop parts
are dry before lighting a burner.
• To avoid a fire hazard, do not hang flammable or
heat sensitive objects over the cooktop.
• Do not climb on any part of the appliance.
WARNING
General Safety Precautions
To reduce the risk of fire, electric shock, or serious injury
or death when using your appliance, follow basic safety
precautions, including the following:
• Do not leave the cooktop unattended while in use to
avoid the possibility of a fire.
• Do not leave children alone or unattended in the
area around the cooktop. Do not allow children to
play with the controls or touch other parts of the
cooktop. Do not store items of interest to children
on top of or above the cooktop. Children could be
burned or injured while climbing on the appliance.
• Keep flammable items, such as paper, cardboard,
plastic, and cloth away from the burners and other
hot surfaces. Do not place such items on the
cooktop. Do not allow pot holders to touch hot sur-
faces or gas burners.
• Do not wear loose or hanging apparel while using
the cooktop. Do not allow clothing to come into con-
tact with the cooktop and surrounding areas during
and immediately after use.
• If the cooktop is near a window, do not use long cur-
tains as window treatment. The curtains could blow
over the cooktop and create a fire hazard.
• Do not use towels or bulky cloth as pot holders.
• Do not use the cooktop to heat sealed containers.
The container and contents may explode, causing
personal injury.
• Non-stick coatings, when heated, can be harmful
to pet birds. Relocate pet birds to a separate, well-
ventilated room when using the cooktop.
IMPORTANT - This appliance is equipped with a
three-prong grounding plug for your protection against
possible electric shock hazards. Plug it only into a
dedicated, grounded three-prong electrical outlet. It is the
responsibility of the customer to make sure the proper
type of outlet is installed.
Under any circumstances:
• DO NOT cut or remove the
third (ground) prong from
the power cord.
• DO NOT use an adapter
plug.
• DO NOT use an extension
cord.
• DO NOT use a power cord
that is frayed or damaged.
• DO NOT connect to an electrical outlet with a ground
fault interrupter (GFI).
WARNING
3-prong
plug
3-prong
outlet
3
Electrical Requirements
WARNING
To prevent an electric shock hazard, the power supply
must meet the specifications stated below. It is the own-
er’s responsibility to make sure that the electrical service
meets electrical requirements and that the electrical outlet
has been properly installed by a licensed electrician.
• The cooktop is supplied with a factory installed,
40-inch, three-prong, grounding electrical cord. It is
connected to the chassis at the bottom right rear corner
(see Chassis Bottom Diagrams below). It must be
connected to a dedicated, grounded three-prong elec-
trical outlet installed by a licensed electrician.
• The electrical installation, including minimum supply
wire size and grounding, must be done in accordance
with National Electric Code ANSI/NFPA 70* and local
codes and ordinances. A copy of this standard may be
obtained from:
National Fire Protection Association
1 Batterymarch Park
Quincy, MA 02269-9101
• The correct voltage, frequency, and amperage must be
supplied to the electrical outlet according to the product
data label located on the bottom of the chassis. See
the Gas and Electrical Requirements table on this
page for reference.
• Be certain to locate the electrical outlet so that the
power cord may be easily disconnected if the unit
needs service.
Gas Supply Requirements
• Be certain that the cooktop being installed is correct
for the gas service being provided (Natural Gas or LP
gas). Also, if using the cooktop at an altitude above
4000 ft. (1219 m) make sure it is equipped for high alti-
tude (“H”) operation.
• Units equipped for high altitude operation have an “H”
at the end of the model number listed on the product
data label.
• Units equipped for LP operation have “LP” in the
model number listed on the product data label. See the
Product Data Label section for label location.
• Check your local building codes for the proper method
of installation. In the absence of local codes, this
appliance should be installed in accordance with the
National Fuel Gas Code ANSI Z223.1/NFPA 54.
• An external manual shut-off valve must be installed
between the gas supply line and the cooktop for the
purpose of turning on or shutting off gas to the appli-
ance.
• The cooktop is shipped from the factory with a regula-
tor in the carton. Use only the regulator provided. The
regulator must be installed between the gas inlet on the
cooktop and the gas shut-off valve.
• The regulator inlet accommodates a 3/4” gas line. The
cooktop inlet itself is equipped with a 3/4” male NPT fit-
ting.
See the DYCT304G and DYCT365G images on the left.
DYCT304G/NG
DYCT365G/NG
DYCT304G/LP
DYCT365G/LP
Gas Type Natural Gas LP Gas
Manifold
Pressure
5-inch Water
column
10-inch Water
column
Min. Gas
Supply
Pressure **
6-inch Water
column
11-inch Water
column
Max. Gas
Supply
Pressure
1/2 psi 1/2 psi
Total Connected
Load
0.25 Amp.
(0.03 kW)
0.25 Amp.
(0.03 kW)
Circuit
Requirement
120 Vac,
60 Hz, 15 Amp.
120 Vac,
60 Hz, 15 Amp.
Gas and Electrical Requirements*
* The electrical and gas data on this page is for reference
only. If the above data does not agree with the product data
label, use the data on the product data label.
** The gas supply pressure for testing the regulator setting
shall be at least 1-inch water column (249 Pa) above the
specified manifold pressure.
Important Safety Instructions
DYCT304G
DYCT365G
Chassis Bottom Diagrams
4
Installation Specifications
WARNING
Observe all governing codes and ordinances during planning and installation. Contact your local building department for
further information.
Product Dimensions
Model DYCT304G
All tolerances: ±1/16” (±1.6 mm) unless otherwise noted.
13/16”
(2.1 cm)
3 3/4”
(9.5 cm)
Gas inlet
Power cord
Chassis
Front of cooktop
Top panel overhang
2 1/8”
(5.4 cm)
5/8”
(1.6 cm)
30”
(76.2 cm)
21”
(53.3 cm)
27 1/2” *
(69.9 cm)
* Including raised embosses on sides of chassis
2 1/8”
(5.4 cm)
Chassis
height
DYCT304G
Power Cord and Gas Inlet Location
top of cooking surface
Bottom of spill tray to
19 1/2” *
(49.5 cm)
4”
(10.2 cm)
5
Installation Specifications
Model DYCT365G
1”
(2.5 cm)
1”
(2.5 cm)
1 3/8”
(3.5 cm)
Gas inlet
Power cord in
Chassis
Front of cooktop
Top panel overhang
2 1/4”
(5.7 cm)
36”
(76.2 cm)
21”
(53.3 cm)
4”
(10.2 cm)
Chassis
height
19 1/2” *
(49.5 cm)
33 5/8” *
(85.4 cm)
* Including raised embosses on sides of chassis
DYCT365G
Power Cord and Gas Inlet Location
2 1/8”
(5.4 cm)
top of cooking surface
Bottom of spill tray to
6
Cabinet and Countertop Layout
WARNING
• To reduce the risk of personal injury caused by
reaching over a hot appliance, avoid locating cabinet
storage space directly above the cooktop.
• Failure to meet or exceed the maximum and mini-
mum dimensions/clearances stated in these instruc-
tions may result in a fire hazard.
• Follow the countertop manufacturer’s instructions
regarding the minimum corner radius, use of heat
reflective tape, reinforcement of corners, etc.
• Carefully check the location where the cooktop will be
installed. For best performance, the cooktop should be
placed away from drafts that may be caused by doors,
windows, and heating and air conditioning vents.
• This appliance is to be used in conjunction with a suit-
able vent hood or approved Dacor downdraft vent.
Refer to the following illustrations and notes for clearance
allowances.
Model (A) Minimum (A) Recommended
DYCT304G 30” (76.2 cm) 36” (91.4 cm)
DYCT365G 36” (91.4 cm) 42” (106.7 cm)
Installation Specifications
Model
(B) Minimum to allow for clearance of
hold-down brackets
DYCT304G 29 in (73.7 cm)
DYCT365G 35 1/4 in (89.5 cm)
• Allow a minimum 1/4” (6 mm) clearance between the
bottom of the cooktop chassis and all combustible sur-
faces, including the upper edge of a drawer inside the
countertop cabinet below the cooktop.
• The gas supply piping, gas shut-off valve, and the elec-
trical outlet must be located so they do not interfere
with the cooktop after it is installed. If installing another
appliance in the cabinet below, allow for the routing of
gas and electrical service behind it.
The installation must allow for the following:
• Access to the gas shut-off valve and regulator when
the unit is installed.
• The 40-inch (101.6 cm) power cord must be able to
reach an electrical outlet, and that electrical outlet must
be easily accessible after the cooktop is installed.
• Access to the underside of the cooktop for service and
inspection purposes.
• Clearance inside the counter to allow for correct instal-
lation of the hold-down brackets.
To allow underneath access to the utilities and cooktop
bottom, a fixed shelf should not be installed below the
cooktop. See the following pages for countertop cutout
dimensions.
Downdraft Compatibility
If installing the cooktop with a downdraft, use only the
approved Dacor downdraft model numbers below:
Cooktop Models Approved Downdraft Models
DYCT304G ERV3015, PRV30, or RV30
DYCT365G ERV3615, PRV36, or RV36
1/4” (6 mm)
min. height clearance
to combustible
surfaces
B
Underneath Cabinet Dimensions
Minimum Required Clearances
Around the Cooktop
13" max.
(33.0 cm)
3
Not required if side cabinets are 6 inches more than the left or right of both edges
of the cooktop. For DYGCT304, it is 5 1/2 inches (14.0 cm)
for DYGCT365. Allow 7 1/2” (19.1 cm) from cutout edge for RGC304,
7” (17.8 cm) for DYGCT365.
A
15" min.
1
(38.1 cm)
1 7/8" min.
(4.8 cm)
Combustible
surface to rear
Combustible overhead
cabinets
30" min.
1, 2
(76.2 cm)
See Note 3
See cutout
dimensions
2
If installing with an overhead vent hood, check the hood
installation instructions for specifications for minimum required clearances.
1
Measured from the cooking surface (top of cooktop grate).
1
Measured from the cooking surface (top of cooking grate).
2
If installing an overhead vent hood, check the hood
installation instructions for the minimum required clearance
specifications and requirements.
3
Not required if the side cabinets are at least 6 inches or
more from both sides of the cooktop.
All tolerances: +1/16” -0” unless otherwise noted.
All tolerances: +1/16” -0” unless otherwise noted.
7
4 1/4" (10.8 cm) min.
from mounting surface to
combustibles below
cooktop chassis
E
F
C
D
Min. distance to combustible side
wall above countertop (both sides)
F
Vertical
combustible
surface
Rear
wall
1 7/8" min.
(4.8 cm)
Installation Specifications
Cutout Dimensions
Stiffener
Cabinet face
Countertop
Floor
5/8” min. (1.6 cm) space
behind downdraft
to clear stiffener
5/8” min. (1.6 cm)
RV Series Downdraft:
check downdraft
specifications to
determine correct fit
23 1/8” (58.7 cm)
required for downdraft
cap clearance
DYCT Gas Cooktop
Cooktop with
Downdraft: ERV/PRV Series
Cooktop with
Downdraft: RV Series
Countertop Cutout
Dimensions
All tolerances +1/16” -0” (+1.6 mm) unless otherwise noted.
Installation Type
(C) Minimum (D) (E) (F)
DYCT304G with no downdraft 2 7/8” (7.3 cm) 19 3/4” (50.2 cm)
27 5/8”
(70.1 cm)
7 1/2”
(19.1 cm)
DYCT304G with ERV3015 or PRV30 3/8” (1.0 cm) 22 1/2” (57.2 cm)
DYCT304G with RV30 5/8” (1.6 cm) 22 1/4” (56.5 cm)
DYCT365G with no downdraft 2 7/8” (7.3 cm) 19 3/4” (50.2 cm)
33 3/4”
(85.7 cm)
7” (17.8 cm)DYCT365G with ERV3615 or PRV36 3/8” (1.0 cm) 22 1/2” (57.2 cm)
DYCT365G with RV36 5/8” (1.6 cm) 22 1/4” (56.5 cm)
Stiffener
Cabinet face
Countertop
Floor
3/8” min. (1.0 cm) space
behind downdraft
to clear stiffener
23 3/8” (59.4 cm)
3/8” min. (1.0 cm)
required for downdraft
cap clearance
ERV or PRV Series
Downdraft: check
downdraft specifications
to determine correct fit
DYCT Gas Cooktop
Countertop Cutout View
8
Verifying the Package Contents
• Hold-down brackets (2)
• Grates: DYCT304G (2), DYCT365G (3)
• Burner sets: DYCT304G (4), DYCT365G (5)
• Gas pressure regulator (1)
• Stainless steel cleaner (1)
(stainless steel models only)
If any parts are missing, see the Replacement Parts List
section on page 12 for Dacor Customer Service and
ordering information.
Installing the Cooktop
WARNING
• Verify that the power supply meets the specifications
on page 3 before proceeding.
• To prevent damage to the gas pressure regulator,
install it only after the cooktop is mounted in its per-
manent position.
IMPORTANT
• Do not over-tighten the hold-down bolts. Over tight-
ening the hold down bolts may result in improper
operation of the dual gas burners.
• Do not use a hardening compound or caulk to perma-
nently seal the cooktop into place. The cooktop must
be readily removable if service is required. Removal
of sealant to service the unit will be performed at the
customer’s expense.
1. If the cooktop will be used with a downdraft, first install
the downdraft according to the downdraft installation
instructions.
2. Lower the cooktop into the cutout and center it.
3. Secure the cooktop to the countertop using the two (2)
hold-down brackets as shown (included).
Installation Instructions
Connecting the Gas Line
WARNING
• Verify that the gas supply meets specifications before
connection. See page 3.
• Do not install or use the cooktop without the included
gas regulator installed.
• Ensure that the arrow on the regulator points in the
direction of the gas flow, toward the cooktop.
• Do not apply excessive pressure when tightening gas
connections and fittings.
• Do not use Teflon tape or plumber’s putty on flexible
gas line connections.
• Before use, test the gas lines for leaks as instructed.
Do not use a flame to check for leaks.
• The maximum gas supply pressure to the regulator
must never exceed 1/2 pounds per square inch (psi)
or 3.5 kPa.
• The cooktop and shut-off valve must be disconnected
from the gas supply piping system during any pres-
sure testing exceeding 1/2 psi (3.5 kPa).
• The cooktop must be isolated from the gas supply
piping system by closing the shut-off valve to the
cooktop during any gas supply piping system pres-
sure testing equal to or less than 1/2 psi (3.5 kPa).
• For LP gas installations, the LP gas tank must have
its own high-pressure regulator in addition to the
pressure regulator supplied with the cooktop.
Refer to the figure Underneath the Cooktop on the left
while following these gas hookup instructions.
1. Attach the gas pressure regulator (included) to the gas
inlet on the cooktop.
• When working in tight space constraints, the regulator
can be installed anywhere between the cooktop and
gas supply/shut-off valve.
• For best performance, attach the regulator as close as
possible to the cooktop. This will minimize gas pressure
loss.
2. Connect regulator to the gas supply/shut-off valve with
a minimum 1/2” flexible gas line (not included).
3. Check for gas leaks:
◊ Turn all cooktop control valves to OFF.
◊ Make a soap and water solution or use a gas leak
detector and check all lines and connections for
gas leaks.
* Make sure the gas supply/shut-off valve is ON.
◊ Turn the gas supply/shut-off valve OFF.
Hold-down bracket
mounting holes
(both sides)
Gas inlet
Power cord
Underneath the Cooktop
Model DYCT365G
9
Installation Instructions
Assembling the Burners
WARNING
• Never attempt to operate the cooktop with any of the burner parts removed.
• Do not attempt to adjust the burner air mixture settings. All adjustments are preset at the factory.
1. Remove the burner heads, burner rings, burner caps, and grates from their shipping packages.
2. Assemble the burners as shown below. When assembling the burner components, twist each piece back and forth
until it drops completely into place.
• The burners will not function properly unless all of the burner pieces are correctly seated.
3. Gently set the grates on top of the spill tray. Make sure that the rubber feet are placed in the indentations located in
the spill tray.
* The SimmerSear burner head is permanently attached to
the burner base. It cannot be removed by the user.
Burner and Grate Diagram for
DYCT304G and DYCT365G
Single Burner
Assembly
SimmerSear™
Burner Assembly
Igniter
Grate
Burner cap
Burner skirt
Burner head *
Burner head
Burner
base
Wide side down
Line up this
notch with
the igniter
Feet
(bottom view)
Cap cover
Cap cover
10
Installation Instructions
Verifying the Correct Setup
WARNING
• Make sure that power to the electrical outlet is turned
off at the circuit breaker panel or fuse box and that
the gas is turned off at the gas supply valve before
proceeding.
• The cooktop must be properly grounded at all times
when electrical power is applied.
Prior to operating the cooktop, read the accompanying Use
and Care Manual carefully.
1. Make sure all the cooktop burner controls are in the
OFF position.
2. Connect the power cord to the electrical outlet.
3. Turn on power to the electrical outlet at the circuit
breaker or fuse box.
4. Press and turn ONE burner control knob slowly left to
the HIGH position. Verify that the associated burner
igniter sparks, then return the knob to the OFF position.
Repeat for all of the remaining control knobs.
5. Turn gas supply valve ON.
6. Perform this IGNITION TEST on all burners:
• Press and turn the control knob slowly left to the
HIGH position. Only the selected burner will spark.
It may take up to four seconds for the burner to
ignite, at which time the igniter will stop sparking.
If ignition does not occur within four seconds, turn
the knob OFF, wait for at least five minutes to allow
any gas to dissipate, then repeat this step.
• Once the burner lights, rotate the control knob
from HIGH toward LOW to adjust the flame height.
SimmerSear™ burners: turn the control knob to
the simmer setting, and make sure the low-level
flame can be adjusted.
• When the unit is installed correctly, the flame will
burn steadily. It will have a sharp, blue inner cone
that will vary in length proportional to the burner
size. The flame will be reduced by the Smart
Flame™ feature under the grate fingers to increase
the life of the grate.
Single Burner
Control Knob
Correct Flame Appearance
Flame
Low
NOTE: If the cooktop does not function properly, follow
these troubleshooting steps:
• Verify that power and gas are supplied to the cooktop.
• Check to make sure that the power cord is connected
to an electrical outlet and that power is turned on at the
circuit breaker, fuse box, or light switch.
• Check to make sure that all the burners are correctly
assembled and seated.
• If the burner continues sparking after ignition, have a
licensed electrician check the electrical outlet for cor-
rect grounding or reversed polarity.
• Repeat the IGNITION TEST (Step 6).
• If the appliance still does not work, contact Dacor
Distinctive Service at (800) 793-0093, ex. 2822. Do not
attempt to repair the appliance yourself. If you need
service, be sure to have the model and serial numbers
available when you call. See inside cover for location.
Dacor is not responsible for the cost of correcting problems
caused by a faulty installation.
SimmerSear™
Control Knob
Flame
Low
High
Low
Simmer
OFF
Burner
Indicator
Burner
Light
Flame
High
On
Simmer
OFF
Burner
Indicator
Burner
Light
Flame
High
On
11
Installation Instructions
Installation Checklist
WARNING
To ensure a safe and proper installation, the following
checklist should be completed by the installer to ensure
that no part of the installation has been overlooked.
Proper installation is the responsibility of the homeowner.
The importance of proper installation of your Dacor
cooktop cannot be overemphasized.
□ Is the electrical outlet for the cooktop grounded and
located according to these instructions and in accor-
dance with all applicable electrical codes?
See page 3.
□ Is the gas service for the cooktop located and installed
according to these instructions and in accordance with
all applicable codes? See page 3.
□ Has the gas supply inlet pressure been measured to
ensure that it does not exceed the maximums stated in
these instructions? See page 3.
□ Is the cooktop secured using the provided hold-down
brackets? See page 8.
□ Is the cooktop connected to the gas supply according
to these instructions and in accordance with all appli-
cable codes? Did the installer check the gas supply for
leaks? See page 8.
□ Are the burners and grates properly assembled accord-
ing to these instructions? See page 9.
□ Has the correct setup been verified? See page 10.
□ Has the warranty been activated on-line or the warranty
card filled out completely and mailed?
12
Replacement Parts List
Replacement parts can be obtained by contacting
Dacor Customer Service.
Dacor Customer Service
Phone: (800) 793-0093 (U.S.A. and Canada)
Monday — Friday 6:00
a.m. to 5:00 p.m. Pacific Time
Model DYCT3xxG Cooktop Parts
See the Burner Parts and Cooktop Layout on right
Cooktop Part
Model
DYCT304G
Model
DYCT365G
Hold-Down Bracket
w/screws (set of 2)
PN 12269 PN 12269
Regulator (Natural Gas
models)
PN 62834 PN 62834
Regulator (LP Gas
models)
PN 72980 PN 72980
Knobs PN 109321 PN 109321
Trim Rings: Single LR
(left rear)
PN 108924-03 --
Trim Rings: Single RF,
RR (right front, right
rear)
PN 108924-02 --
Trim Rings:
SimmerSear™
LF (left front)
PN 108925-02 --
Trim Rings: Single RR,
CR, LR (right rear, cen-
ter rear, left rear)
-- PN 108924-01
Trim Rings:
SimmerSear™ LF, CF
(left front, center front)
-- PN 108925-01
Grate: large PN 108900 PN 108900
Grate: small -- PN 108901
Grate support feet (4) PN 103712 PN 103712
Stainless steel
cleaner
PN A302 PN A302
Model DYCT365G
See the Burner Parts and Cooktop Layout on right
Burner Part Dacor P/N
Cap Cover: LF (left front) 92232
Burner Cap: LF (left front) 92230
Burner Skirt: LF (left front) 92226
Cap Cover: LR, RR (left rear, right rear) 92235
Burner Head: LR, RR (left rear, right rear) 103735
Cap Cover: CF (center front) 92231
Burner Cap: CF (center front) 92460
Burner Skirt: CF (center front) 92459
Cap Cover: CR (center rear) 92236
Burner Head: CR (center rear) 103737
Model DYCT304G
See the Burner Parts and Cooktop Layout on right
Burner Part Dacor P/N
Cap Cover: LF (left front) 92231
Burner Cap: LF (left front) 92460
Burner Skirt: LF (left front) 92459
Cap Cover: LR, RF (left rear, right front) 92235
Burner Head: LR, RF (left rear, right front) 103735
Cap Cover: RR (right rear) 92236
Burner Head: RR (right rear) 103737
Replacement Parts List
Grate: Large
Grate: Small
Grate Sizes
For models For model
DYCT304G, DYCT365G DYCT365G
13
DYCT304G
Replacement Parts List
Single Burner
Assembly
* Burner head on SimmerSear
is attached to the spill tray.
Burner Parts
Cooktop Layout
Left Rear
Right Rear
Center Rear
Left Front
Right Front
Center Front
Burner Location
LR
RR
CR
LF
RF
CF
DYCT365G
& Trim ring
Spill tray
Grate
SimmerSear™ control knobs
LR
CR
RR
LF CF
Burner control knob
& Trim ring
Grate
Spill tray
LR
RR
LF
RF
& Trim ring
SimmerSear™ control knob
Burner control knob
& Trim ring
SimmerSear™
Burner Assembly
Igniter
Grate
Burner cap
Burner skirt
Burner head *
Burner head
Wide side
down
Line up this
notch with
the igniter
Feet
(bottom view)
Cap cover
Cap cover
Burner
base
14
Wiring Diagrams
AFTER SERVICING
VERIFY PROPER OPERATION
120V, 60Hz.
POWER SUPPLY
CAUSE IMPROPER AND DANGEROUS OPERATION.
WHEN SERVICING CONTROLS. WIRING ERRORS CAN
CAUTION: LABEL ALL WIRES PRIOR TO DISCONNECTION
WIRING DIAGRAM
DYCT304G
15
Wiring Diagrams
AFTER SERVICING
VERIFY PROPER OPERATION
120V, 60Hz.
L
POWER SUPPLY
CAUSE IMPROPER AND DANGEROUS OPERATION.
WHEN SERVICING CONTROLS. WIRING ERRORS CAN
CAUTION: LABEL ALL WIRES PRIOR TO DISCONNECTION
WIRING DIAGRAM
DYCT365G
N
BK
GRN
W
INDICATOR LED CF
BK
1
2
1
2
4
3
5
6
7
9
8
10
11
12
1
5
9
6
12
2
10
7
11
4
3
8
BK
INDICATOR LED LF
BK
INDICATOR LED RR
BK
INDICATOR LED CR
BK
INDICATOR LED LR
+
+
+
+
+
+
-
-
-
-
-
-
ISOLATOR
BOARD
P/N 106104
L1
IGNITOR,
LR BURNER
W
N
RE-IGNITOR
RED
NO SWITCH
S1
BK
BK
BK
W
RE-IGNITOR
IGNITOR,
CR BURNER
N
S2
BK
NO SWITCH
L1
RED
W
BK
RE-IGNITOR
IGNITOR,
RR BURNER
N
S3
BK
NO SWITCH
L1
RED
W
BK
L1
NO SWITCH
N
NEON SIMMER
INDICATOR LIGHT
BK
IGNITOR,
LF BURNER
W
IGNITOR,
CF BURNER
S5
BK
BK
RE-IGNITOR
RED
BK
BK
RE-IGNITOR
BK
S4
L1
W
S4
RESISTOR
BK
NO SWITCH
BK
S5
RESISTOR
N
RED
NEON SIMMER
INDICATOR LIGHT
W
W
W
W
W
NC SWITCH
(OPEN POSITION)
NC SWITCH
(OPEN POSITION)
W
W
W
W
W
W
Dacor ● 14425 Clark Avenue, City of Industry, CA 91745 ● Phone: (800) 793-0093 ● Fax: (626) 403-3130 ● www.dacor.com
-
1
-
2
-
3
-
4
-
5
-
6
-
7
-
8
-
9
-
10
-
11
-
12
-
13
-
14
-
15
-
16
-
17
-
18
Dacor HPCT365GSNG Installation guide
- Type
- Installation guide
- This manual is also suitable for
Ask a question and I''ll find the answer in the document
Finding information in a document is now easier with AI
Related papers
-
Dacor DCT365SLP Combined Configuration Cooktop or Range with Downdraft
-
Dacor HPCT365GSNG User guide
-
Dacor DCT365 User manual
-
-
-
-
-
-
-
Other documents
-
KitchenAid KGCS105G User manual
-
Hallman HGC2401ST User guide
-
GE UXB636BPTS Installation guide
-
Samsung DTG36P875NS Installation guide
-
Beckett CG15/CG25/CG50 Gas Burner Owner's manual
-
-
Maytag MGC7630WB - 30 in. 4 Burner Gas Cooktop User manual
-
PH7 H10 Installation guide
-
Sharper Image Personal Air Purifier Owner's manual
