John Lewis JLHDA633 User manual

Brand: John Lewis

Model: JLHDA633

Category: Cooker hoods

Type: User manual

John Lewis JLHDA633 is a built-in cooker hood designed for use above a cooking area. It can be used in the extraction (ducted to the outside) or recirculation mode. The cooker hood is more effective when installed in the extraction mode (ducted to the outside). Venting kits may be purchased through your retailer or DIY store, and must be evacuated through an outside vent of ø125 (5ins) or ø150mm (6ins). When the cooker hood is ducted to the outside the charcoal filter must be removed.

JLHDA633

Built-in cooker hood

Instruction manual

Important safety information

It is most important that this instruction manual should be retained with the appliance for future ref-

erence. Should the appliance be sold or transferred to another owner, or should you move house and

leave the appliance, always ensure that the book is supplied with the appliance in order that the new

owner can get to know the functioning of the appliance and the relevant warnings. These warnings

have been provided in the interest of safety . You MUST read them carefully before use or instal-

lation by a qualied person. If you are unsure of the meanings of these warnings contact the John

Lewis branch from which you purchased the appliance.

Installation

• Any installation work must be undertaken by a quali-

ed and competent person to the relevant National

Standards.

• This hood must be installed in accordance with the

installation instructions and all measurements must

be adhered to.

• If the cooker hood is installed for use above a gas

appliance then the provision for ventilation must be

in accordance with the Gas Safety Codes of Practice

BS.6172, BS.5440 and BS.6891 (Natural Gas) and

BS.5482 (LP Gas) 1994, the Gas Safety (Installation

& Use) Regulations, the Building Regulations issued

by the Department of the Environment, the Building

standards (Scotland) (Consolidated) Regulations is-

sued by the Scottish Development Department.

• The fan motor of this cooker hood incorporates a

cut-out device which will operate if the cooker hood

is installed below the minimum height recommended

under section ‘Clearance Height’, or if the motor be-

comes overheated. If the cut-out device is activated,

switch off the fan motor and allow the cooker hood

to cool. The cut-out device will reset itself when the

fan motor has cooled signicantly.

• It is dangerous to alter the specications or modify

this product in any way.

• When installed between adjoining wall cabinets the

wall cabinets must not overhang the hob.

• If the room where the hood is to be used contains

a fuel burning appliance such as a central heating

boiler then its ue must be of the room sealed or

balanced ue type.

• If other types of ue or appliances are tted ensure

that there is an adequate supply of air to the room.

• The ducting system for this appliance must not be

connected to any existing ventilation system which

is being used for any other purpose.

• Do not install above a cooker with a high level grill.

Child Safety

• This appliance is designed to be operated by adults.

Children should not be allowed to tamper with the

controls or play with the appliance.

• Keep all packaging materials away from children.

Use

• This product is for domestic use only.

• Never leave frying pans unattended during use as

over-heated fats and oils might catch re.

• Never do ambé cooking under this cooker hood.

• Do not leave naked ames under the hood.

• This cooker hood is designed to extract unpleasant

odours from the kitchen, it will not extract steam.

Maintenance and Cleaning

• This appliance can be a hazard if the synthetic paper

and charcoal lters are not replaced as recommended.

Service

• Under no circumstances should you attempt to repair

the appliance yourself. Repairs carried out by inex-

perienced persons may cause injury or more serious

malfunction. Refer to your local Service Force Centre.

Always insist on genuine spare parts.

Environmental Information

• After installation please dispose of the packaging with

due regard to safety and the environment.

• The symbol on the product or on its packaging

indicates that this product should not be treated as

normal household waste. Instead it should be taken

to the appropriate collection point for the recycling of

electrical and electronic equipment. By ensuring this

product is disposed of correctly, you will help prevent

potential negative consequences for the environment

and human health, which could otherwise be caused

by inappropriate waste handling of this product. For

more detailed information about recycling of this

product, please contact your local council, your

household waste disposal service or the shop where

you purchased the product.

For the User

Important Safety Information 2

Description of the Appliance 4

Using the cooker hood 9

Cooker Hood Controls 9

To Operate 9

Recirculation 9

Extraction 9

Maintenance and Cleaning 10

External Cleaning 10

Cleaning the Ducting panels 10

Metal Grease Filters 10

Charcoal Filters 11

To Remove/Replace Charcoal Filter 11

Changing the Halogen Spot Lamp 11

Something Not Working 12

Repairs and After Sales Service 12

Contents

For the Installer

Electrical Connections 8

Electrical Requirements 8

Electrical Connection 8

Installing the Cooker Hood 5

Installation Requirements 5

Unpacking 5

Fitting the Wall Brackets 6

Fitting the Canopy Hood 6

Extraction 7

Recirculation 7

Guide to use the Instruction Manual

The following symbols will be found in the text to

guide you through the instruction book

Step by step instructions

This appliance complies with the

followings E.E.C. Directives:

- 89/336 (Electromagnetic Com-

patibility Directive)

- 73/23 (Low Voltage Directive)

- 93/68 (General Directives)

and subsequent modications

Safety instructions

Environmental Information

Description of the appliance



































Please ensure that when the appliance is installed

it is easily accessible to an engineer in the event of

a breakdown.

All installations must comply with the local

authorities requirements for the discharge of

exhaust air.

Incorrect installation may affect the safety of this

cooker hood.

Installation Requirements

Before installation check the wall to which the

cooker hood is to be tted for electric cables,

water pipes or gas.

The chimney hood must be installed according

to the instructions suppliers below and by quali-

ed and competent personnel to the relevant

National Standards.

This cooker hood is designed to be xed to any vertical

surface over a cooking area, and can be used in the

extraction (ducted to the outside) or recirculation mode.

The installation work must be undertaken by a qualied

and competent person.

The manufacturer disclaims any responsibility for damage

due to incorrect installation of the cooker hood or if the

hood is not installed in compliance with relevant regula-

tions controlling this type of installation.

Installation





















 









W











 

















Unpacking

Before unpacking the cooker hood position the carton with

the arrows pointing upwards as illustrated on the carton.

The cooker hood is made up of the following components:

Ref Qty Product Components

1 1 Canopy complete with: Controls, Lighting,

Fan Assembly, Grease Filter, Charcoal

Filter.

2 1 Telescopic Chimney Comprising:

2.1 1 Upper Chimney

2.2 1 Lower Chimney

8a 1 Right-Hand Recirculation grille

8b 1 Left-Hand Recirculation grille

9 1 Flange 150-120

10 1 Flange 120-125

14 1 DuctingExtension Pipe

14.1 1 Recirculation Outlet Extension

15 1 Recirculation Outlet Adapter

Ref Qty Installation Components

7.1 1 Hood Body Fixing Brackets

7.2.1 2 Upper Chimney Section Fixing Brackets

7.3 1 Air Outlet Connection

11 6 Wall Plugs

12a 6 Screws 4,2 x 44,4

12c 6 Screws 2,9 x 6,5

12e 2 Screws 2,9 x 9,5

12t 2 Screws 3,5 x 9,5

22 2 Washers

Ref Qty Documentation

1 Instruction booklet

Fitting the wall brackets

• Draw a vertical line on the supporting wall up to the

ceiling, or as high as practical, at the centre of the

area in which the hood will be installed.

• Draw a horizontal line at 650 mm above the hob.

• Place bracket 7.2.1 on the wall as shown about

1-2 mm from the ceiling or upper limit aligning the

centre (notch) with the vertical reference line.

• Mark the wall at the centres of the holes in the

bracket.

• Place bracket 7.2.1 on the wall as shown at X mm

below the rst bracket (X = height of the upper

chimney section supplied), aligning the centre (notch)

with the vertical line.

• Mark the wall at the centres of the holes in the

bracket.

• Mark a reference point as indicated at 116 mm from

the vertical reference line and 306 mm above the

horizontal reference line.

• Repeat this operation on the other side.

• Drill ø 8 mm holes at all the centre points marked.

• Insert the wall plugs 11 in the holes.

• Fix the lower bracket 7.2.1 using the 12a screws

(4,2 x 44,4) supplied.

• Fix the upper bracket 7.2.1 using the 2 screws 12a

(4,2 x 44,4) supplied.

• Fix the Hood Body Fixing Brackets 7.1 using the 2

screws 12a (4,2 x 44,4) and Washers 22 supplied,

checking levelling.

Note: If the hood is to be installed onto a hollow

construction or plaster or partition board wall

then special xing screws will be required (not

supplied).

Fitting the canopy hood

• Hook the hood canopy onto the bracket 7.1.

• Tighten denitly the Hood with 2 screw 12t.

Hook both sides of the hood at the same

time.

Installing the cooker hood

7.1

Extraction (Ducted)

The cooker hood is more effective when installed in

the extraction mode (ducted to the outside).

Venting kits may be purchased through your retailer

or DIY store, and must be evacuated through an

outside vent of ø125 (5ins) or ø150mm (6ins).

The ducting used must be manufactured from re

retardant material conforming to the relevant British

Standard or DIN 4102-B1.

When the cooker hood is ducted to the outside

the charcoal lter must be removed.

Fitting the Ducting

• When installing the ducted version, connect the hood

to the chimney using either a exible or rigid pipe

ø 150 or 125 mm, the choice of which is left to the

installer.

• To install a ø 125 mm air exhaust connection, insert

the reducer ange 9 on the hood body air outlet and

the adapting ring ø120-125 10 on the reducer ange.

• Fix the pipe in position using sufcient pipe clamps

(not supplied).

• Remove any activated charcoal lters.

Recirculation Mode

The cooker hood is supplied specied for use in the recirculation

mode, with the charcoal lter tted.

In the recirculation mode contaminated air is passed through

the charcoal lter to be puried and recirculated into the kitchen

through the grille outlets on either side of the chimney.

• Assemble the two halves of the hood body extension

piece 14.

• Push t the assembled hood body extension piece 14

onto the air outlet.

• Push t connection 15 onto the hood body extension

piece 14.

• Insert the connection extension pieces laterally 14.1 in

connec-tion 15.

• Make sure that the outlet of the extension pieces 14.1

is hori-zontally and vertically aligned with the chimney

outlets. If this is not the case, adjust the position by either

reversing the con-nection extension pieces 14.1 or by

cutting the hood body ex-tension 14 along one of the

thinner section channels denoting the pre-xed lengths,

then reassemble as described previously.

• The air outlet directional grills 8a - 8b must be tted

after the lower outlet duct has been installed.

• Ensure that the activated charcoal lters have been

inserted.



















Fitting the Upper Chimney

• Expand the sides of the upper chimney stack item 2.1 and

place the chimney over the two brackets 7.2.1 ensuring

they are well seated.

• Secure the chimney stack to the brackets 7.2.1 using the

four self tapping screws item 12c (2.9 x 9.5mm) supplied.

Fitting the Lower Chimney

• Expand the of the lower chimney stack item 2.2 and place

the chimney over the upper chimney stack item 2.1 and

the canopy.

• Secure the chimney stack to the canopy using the two

screws item 12c (2.9 x 9.5mm) supplied.

• After the chimney has been secured into position, insert the

two plastic recirculation grilles item 8a (right-hand) and 8b

(left-hand) in the apertures on each side of the chimney.

The grilles are marked with two arrows and should be tted

with one arrow pointing upwards and the other toward the

front.

• IWhen the hood is used in the recirculation mode ensure

that the grilles are properly secured to the recirculation

extension spigot item 14.1.















Electrical connection

Electrical requirements

Any permanent electrical installation must comply with the lat-

est I.E.E. Regulations and local Electricity Board regulations.

For your own safety this should be undertaken by a qualied

electrician e.g. your local Electricity Board, or a contractor who

is on the roll of the National Inspection Council for Electrical

Installation Contracting (NICEIC).

Electrical connection

Before connecting to the mains supply ensure that the mains

voltage corresponds to the voltage on the rating plate inside

the cooker hood.

Remove the grease lters (see paragraph Maintenance)

making sure that the connector of the feeding cable is correctly

inserted in the socket placed on the side of the fan.

This appliance is tted with a 3 core mains cable and must be

permanently connected to the electricity supply via a double-

pole switch having 3mm minimum contact gap on each pole.

A Switched Fuse Connection Unit to BS1363 Part 4, tted with

a 3 Amp fuse, is a recommended mains supply connection

accessory to ensure compliance with the Safety Requirements

applicable to xed wiring instructions.

This appliance conforms to BS 800: 1988 and EEC Directive

No. 78 308 regarding suppression of radio and television

interference.

THIS APPLIANCE MUST BE EARTHED

Using the cooker hood

The cooker hood is designed to extract unpleasant

odours from the kitchen, it will not extract steam. The

appliance can be installed to recirculate or extract

contaminated air.

Cooker hood controls









Button Led Function

T1 Speed

On Turns the Motor on at Speed one.

- Turns the Motor off.

T2 Speed On

Turns the Motor on at speed two.

T3 Speed Fixed

When pressed briefly, turns the Motor on at

Speed three.

Flashing Pressed for 2 Seconds.

Activates Speed four with a timer set to 10

minutes, after which it returns to the speed

that was set previously. Suitable to deal with

maximum levels of cooking fumes.

L Light -

Turns the Lighting System on and off.

Warning: Button T1 turns the motor off, after first

passing to speed one.

To operate

Select the required fan speed and light if required.

Recirculation

In the recirculation mode the contaminated air enters

the cooker hood through the grease lters. The air is

cleaned by passing through the charcoal lters before

being passed back into the kitchen through the grilles in

either side of the chimney stack.

Extraction

In the extraction mode the contaminated air enters the

cooker hood passing through the grease lters and is

passed out through the ducting into the atmosphere.

To obtain the best performance when cooking it is ad-

visable to switch the cooker hood on for a few minutes

before you start cooking and leave it running for about

15 minutes after nishing.

When used in the ducting mode the charcoal

lters are not required.

Never do ambé cooking under this cooker

hood.

Never leave frying pans unattended during use,

as over-heated fats and oils can catch re.

Do not leave naked ames under the cooker

hood.

Ensure heating areas on your hob are covered

with pots and pans when using the hob and

cooker hood simultaneously.

Before carrying out any maintenance or

cleaning isolate the cooker hood from the

mains supply.

The cooker hood must be kept clean, as a

build up of grease or fat can be a re hazard.

External cleaning

Wipe the cooker hood frequently with warm soapy

water using a mild detergent.

Never use scouring pads or abrasive clean-

ers.

Never use excessive amounts of water when

cleaning particularly around the control

panel.

Metal grease lters

The grease lters absorb grease and dust during

cooking to help keep the cooker hood clean inside,

and should be cleaned at least every 2 months of

operation, or more frequently for particularly heavy

usage.

Cleaning the lters

It is not necessary to unhook the central duct-

ing panel from the shackle.

Remove the metal grease lters

• Remove the lters one at a time by pushing them

towards the back of the group and pulling down at

the same time.

• The metal grease lters should be washed, by hand,

in mild soapy water or in a dishwasher. Allow to dry

completely before replacing. Any kind of bending of

the lters has to be avoided when washing them.

• When tting the lters into the hood pay attention that

they are mounted in the correct position and that the

handle faces outwards.

• Reconnect the central ducting panel at the same time

with all 2 hands.

Maintenance and cleaning

Before carrying out any maintenance or

cleaning isolate the cooker hood from the

mains supply.

Charcoal lters

In the recirculation mode the charcoal lters absorb

smells and unwanted odours.

The charcoal lters cannot be cleaned, we recom-

mend they should be replaced approximately every

three months or more often if the hood is used for

more than three hours per day.

To Remove/Replace the char-

coal lters

• First remove the metal grease lters.

• Remove the saturated activated charcoal lter by

releasing the xing hooks as illustrated.

• Position the new charcoal lter in the position marked

and while holding the lter replace the xing hooks as

illustrated.

This appliance can be a possible re hazard

if the grease and charcoal lters are not

cleaned and replaced as recommended.

Changing Lighting unit

Warning: This appliance is tted with a white LED lamp

classed as 1M according to EN 60825-1: 1994 + A1:2002

+ A2:2001 standards; maximum optical power emitted

@439nm: 7µW. Do not look directly at the light through

optical devices (binoculars, magnifying glasses…).

• For replacement contact technical support. ("To pur-

chase contact technical support")

Something not working

Repairs and after sales service

If the appliance is not working correctly, please carry out the following checks, before contacting your local

Service Force agent.

IMPORTANT: If you call out an engineer to a fault listed below, or to repair a fault caused by incorrect use

or installation, a charge will be made even if the appliance is under guarantee.

Symptom

The cooker hood will not start

The cooker hood is not working effectively

The cooker hood has switched off during

operation

Solution

• Check the hood is connected to the electricity supply.

• Make sure the switch is in the ‘ON’ position.

• Check that the fan speed is set high enough for the

task

• Ensure the grease lter is clean.

• Ensure the kitchen is adequately vented to allow the

entry of fresh air.

• If set up for recirculation, check that the charcoal lter

is still effective.

• If set up for extraction, check that the ducting and

outlets are not blocked.

• The safety cut-out device has been tripped.

• Turn off the hob and then wait for the device to reset.

In the event of your appliance requiring service, or if

you wish to purchase spare parts, please contact our

extended warranty administrators by telephoning:

0870 01 07887

They will give you details for your local Service Force

Centre.

Before calling out an engineer, please ensure you

have read the details under the heading “Something

Not Working”.

Your oven is covered by a 3 year parts and labour

guarantee (see separate details given at point of

sale). Please retain your purchase receipt safely for

the service engineer to verify the purchase details.

When you contact the Service Force Centre you will

need to give the following details:

1. Your name, address and post code

2. Your telephone number

3. Clear and concise details of fault

4. The model and serial number of the appliance

(found on the rating plate - see picture)

5. The purchase date.

Please note that a valid purchase receipt is required

for in-guarantee service calls.

991.0363.333_01 - 150216

John Lewis Partnership

171 Victoria Street

London SW1E 5NN

www.johnlewis.com

John Lewis JLHDA633 User manual

Brand: John Lewis

Model: JLHDA633

Category: Cooker hoods

Type: User manual

Download PDF

report

John Lewis JLHDA633 User manual

John Lewis JLHDA633 User manual

Related papers

Other documents